EXTREMA XP-610 SINGLE SIDED PLANER24" Width capacity, 8-3/4" thickness, solid cast iron construction. -- 10 HP main drive motor -- Precision ground cast iron table w/motorized height adjustment, with digital thickness display; 1/2 HP elevation motor. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- Variable feed speed from 20 to 42 FPM; 1 HP feed drive. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit.

EXTREMA XP-615 Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- VECTOR Carbide insert helical cutterhead -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustments

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

COMPLETE FANUC 125I ROBOTIC PALLETIZING SYSTEM System Includes the following: -- FANUC M-410IB/160 Palletizing Robot with Controller and Stand -- Robot will be tested -- End of Arm Tooling to Pick, Fork Style, Picking 94 Lbs Concrete Bags -- Master System Control Panel, 480 VAC 3PH & 24VDC Controls with HMI -- Allen-Bradley Light Curtain with Safety Controller --Infeed Chain Drive Roller Conveyor 10 Feet -- Pallet Hopper. ÷ Safety Fencing COST -- 20 Feet Exit CDLR Pallet Conveyor 52" Wide -- System Integration / Programming.

FANUC 165 Complete Palletizing SystemEquipped with and includes: -- FANUC 165 Complete with R-2000iA Controller with 600mm stand -- Pick-Up Arm Gripper Arm for pillow bag type -- 5 Feet x 24" Motorized In-feed Belt Conveyor -- (1) 10' Motorized Pallet Conveyor -- Automatic Pallet Dispenser -- Price includes Loading on your Truck

FANUC - S430iW, ...RobotFANUC Robot for palletizing rectangular compressed bags.Specifications -- (6) Axes. -- Payload: 165 kG (255 Lbs). -- H-Reach: 2,643 mm (104"). -- Robot mass: 1,300 kG (2,860 Lbs). -- Complete with: Pendant control. -- Complete with: Gripper type arm and pallet gripper. -- Refurbished with (90) days Warranty. -- Buyer to install safety guards.NOTE: Machine was rebuilt is 2021.

END ARM TOOLING FOR FANUC ROBOT -- Gripper Finger Type End Arm Tooling -- Design for Fanuc Robot Model S-430iW -- Loaded on your truck

FANUC 410 Palletizing systems with Infeed and OutfeedComplete Fanuc Case Palletizing System to include: -- Fanuc 410 Palletizing robot, Refurbished/Production ready -- Tooling for palletizing boxes (mechanical gripper) -- Rates of up to (35) boxes per minute sustained rate, robot will pick multiple boxes per cycle. -- Infeed conveyor (10' length) for orienting boxes for picks -- Pallet dispenser with pallet index chain --15' of motorized pallet conveyor -- Master Control panel for complete machine control from a single HMI touchscreen for user friendly operation -- Complete system programming, (6) pallet patterns. -- Complete AGS UL guarding package with safety controller and light curtains. -- 1-Year no charge tech support and remote access to machine.Professional factory installation - will be quoted separately.

FARR GOLD GS4 DUST/FUME/MATERIAL COLLECTOR: 3,000 CFM Rated cap., 1,300 sq. ft. filter area from (4) cartridge filters, approx. 2.3:1 air: cloth ratio . -- Equipped with: 5 HP Pull thru motor; dirty air is pulled into the filter area at bottom of filter media section allowing gross dust particles to fall into collector barrels located beneath pyramidal hopper discharging to a sealed drum (not included) -- Fine dust is pulled up thru the cartridge filters; dust filter cartridges are cleaned by automatic pulse jet with minimum compressed air consumption; cleaned air continues thru blower and is returned to the building air supply thru a silencer.. -- Includes: Cyclone with slide gate discharging into a sealed barrel (not included), electrical control panel, support stand with clearance under hopper, discharge for a waste bin,. access door, some pipe as pictured. -- Note this unit is still in use. Please inquire for availability date.

FCM - RS-30: 30 HP Vertical Feed Hammer HogSpecifications -- Intake: 14" x 18". -- Drive motor: 30 HP. -- Extraction: 8" Diameter. -- Screen with: 3/4" Holes. -- Magnetic starter.

FELDER - G-330: Edgebander0.4 - 3 mm Edge thickness cap.; 40 mm panel thickness; 3" min. width; 4-3/4" min. panel length.Equipped with: -- Quickmelt TEFLON coated glue pot for granular hot-melt adhesive. -- Heavy-Duty Guillotine: Up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations -- Single motor; Double Blade End Trim with: HF Motor; 12,000 RPM. -- Top & Bottom Flush/Bevel Trim: Bevels 0° - 15°; 1/2 HP motor - 12,000 RPM each. -- Open space at outfeed. -- Single feed speed: 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations; outrigger panel support; used tooling.NOTE: Seller states that the equipment has less than (500) hours of use!

FELDER FORMAT4 - Profit H08: Flat Table Machine (w/Offloading) -- Specifications5' x 10' "MATRIX" Phenolic Flat Table design for: "Nested Base" Manufacturing. -- Working Capacity"X" Axis is 121.6" (3,090 mm); "Y" axis is 60.2" (1,530 mm);"Z" axis stroke is 11.8" (300 mm); max. material thickness is 4.3" (110 mm). -- Positioning Speed"X" & "Y" Axis at 197 FPM (60 MPM); "Z" axis is 49 FPM (15 MPM). -- WorktableWorking area is subdivided into (8) vacuum fields (H08 16.31) to: Ensure the best holding force for the most varied board sizes.The vacuum fields are controlled manually by means of: Hand levers on the front side of the machine. Prepared for (optional) elevated pods: Allows profile & horizontal machining. -- Boring Unit(1) DH 8-Spindle Vertical Drill block: On 32 mm centers. -- Machining(1) 13.4 HP (10 kW) Vertically mounted electro spindle Router with: HSK F63 Adaptor; inverter driven 1,000 - 24,000 RPM; max. torque from 12,000 RPM.(1) 15-Position ATC Tool Rack: Mounted at the end of the machine. -- Operator & Machine ControlPC Based user-friendly; icon driven control housed on the: Main machine base + "WOODFLASH" Operating System. -- Complete with:(2) 250 m³/Hr Vacuum pumps; handheld terminal with: Potentiometer & emergency stop; automatic measuring system of the tool length.Sound absorbing protective head enclosure with: Debris curtain around bottom edge. -- Options Include: Automatic unloading unit with: Electromotive offloading pusher. This addition allows finished workpieces to be automatically pushed off the table after processing: Reducing manual handling & speeding up production cycles. -- Actual model: FELDER FORMAT4 - PROFIT H08 16.31

HOMAG - OPTIMAT KDF 440C: Special RH Feed Direction Edgebander w/Premilling & Corner Rounding (aka BRANDT - KDF 440C)Specifications: Premilling & Corner Rounding; HIGHFLEX Automated package. -- Edge & Workpiece Capacity: 0.4 - 8 mm (0.016 - 5/16") Edge; 8 - 60 mm (5/16 - 2-3/8") panel thickness; 160 mm (6-3/8") min. panel length; 70 mm (2-3/4") min. panel width.Equipped with: -- Premilling Station: (2) Motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation w/pneumatic jump control for chipfree & clean panel edges. Equipped with diamond cutterheads -- Infeed Fence with: Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between: Glue roller and pressure section. -- Automatic Edge Magazine: Strip & coil stock; strips: 0.4 mm - 8 mm (0.016 - 5/16"); coils up to 3 mm PVC; "HD" guillotine "Quick Change" Glue Tank for maintenance & glue color change. -- Pressure Section: 1st Roller driven plus: (3) Idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable 8 - 14 MPM (26 - 46 FPM); 11 MPM (36 FPM) when using contour trimming. -- BRANDT "Power Touch Control"; memory: 256 MB RAM; 1 GB flash card drive; Operator control panel: 22" Color HD widescreen; soft keypad; internal modem for remote diagnostic link.Workstations -- End Trimming -- (2) Motor @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: Top/Bottom (2) motors; 0.55 kW (3/4 HP) - 12,000 RPM; auto. tilt positioning; 0° - 25° with combination flush/radius/chamfer cutterheads; horizontal & vertical tracing wheels.Equipped with: Brushless multiaxis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes: (3) Positioning options: Profile-1, Profile-2; flush trimming -- Corner Rounding Unit(1) Motor: 0.35 kW (1/2 HP) - 12,000 RPM for leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness -- Scraping, multi-profile (PVC): Top/Bottom with (2) profiles.1 mm & 2 mm or 3 mm instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels. - PVC scrape collection box. -- Scraping Glue Unit: Flush Top/Bottom on panel surface with floating insert knives. -- Buffing Unit: Top/Bottom (2) motors; 0.10 kW (0.125 HP) - 2,800 RPM. -- RIEPE anti-adhesion and RIEPE detergent.Complete with: -- Motorized, programmable holddown pressure beam; padded sound enclosure and used tooling. -- Actual Model: RH Feed HOMAG - OPTIMAT KDF 440C (aka BRANDT - KDF 440C, but branded HOMAG).

HOMAG - AMBITION 2480: Edgebander (w/Premill & Corner Rounding) -- SpecificationsWorking Capacity. Coiled stock: Min./max. edge thickness 0.3 - 3 mm (0.011. - 0.118").Strip material min./max. Edge Thickness: 0.3 - 20 mm (0.011 - 0.78").Solid Wood Material min./max. Edge Thickness: 0.6 - 20 mm (0.024 - 0.78").Panel stock min/max thickness: 8 - 60 mm (0.472" - 1.574"); panel overhang: 30 mm (1.18").Min. workpiece width 2.36" (60 mm) with workpiece thickness ≤ 22 mm; 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units Top/Bottom spraying device prior to workpiece premilling. Designed for applying a separating agent for: Easier cleaning of any residual glue on the panel. -- Infeed FencePreheated, manually adjustable infeed fence with: Digital indicators. -- Premilling Station(2) 2.2 HP (3.0 kW) - 150 Hz - 9,000 RPM: Vertical jointing spindle motors; equipped with: Panel blow off device & SIKO digital counters for adjustments. -- Preheat UnitQuartz lamp for: Heating substrate edge before glue application. -- Edge MagazineMultipurpose 2-coil magazine expands capability by: Running coiled material & strips. Max. roll diameter: 400 mm & 830 mm.Magazine height adjustment. Allows greater usage of varying panel heights by raising & lowering the magazine table; allows the Operator to center the panelon the edgebanding. -- Gluing System: HOMAG Quickmelt Premelting Unit. QA 3: Quick Melt Overhead Unit & Heated roller applicator; digitally displayed thermostat for both upper & lower unit. 34 mm Dia. Glue Roller. Allows excellent control of temperature for: Optimum bonding results with individual adjustment for leading & trailing glue gates.Lower melting unit equipped with: Automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast 5-minute heat up time. -- Pressure SectionProgrammable (Servo). Automatic pressure zone adjustment: (1) Large 150 mm dia. driven; (4) 70 mm dia. idle rollers; pneumatic pressure control depending on edgebanding material used.Workstations -- End Trimming Unit: PK 25(2) 1 HP (0.8 kW) - 200 Hz - 12,000 RPM Motor ea.: Cuts excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. - Programmable (Servo). -- Rough/Pre-Trimming Unit - BF 10(2) 0.55 kW (0.74 HP) - 12,000 RPM Motors; tilting range: +/- 1° & Counterrotating to machine feed to prevent blowout.Height adjustment synchronized with: The top pressure-beam. -- 4-Motor Corner Rounding Unit: FF 32(4) 0.54 HP (0.4 kW) - 12,000 RPM; Motors to fine trim the edge overhangs at the workpiece front & rear vertical edge.Max. feed speed: 20 MPM (66 FPM) when using "Corner Rounding Unit". -- Open Space -- Profile/Bevel Scraping Unit PN 10Top & Bottom for thick PVC/ABS; electro-pneumatic positioning & pneumatically activated. Pneumatically controlled blow off nozzles. Height adjustment synchronized with: Top pressure beam. -- Flat Glue Scraper Uni

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor.Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG OPTIMAT KAL 210/7/A20/S2 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Working Capacity: Edge thickness cap.: 0.4 - 20 mm; min. panel width: 55 mm (2-1/4"); panel thickness: 12 - 60 mm; min. edge length: 7.8". -- Infeed Section:(2) Premilling heads, each with 3 kW - 6,000 RPM motor, (1) with jump control; chip blowoff unit after last head; SIKO digitals for horizontal & turret for vertical adjustments; -- Preheating infeed fence for panel edge. -- Automatic 2-coil feed magazine for coil material up to 3 mm thickness; strip feed magazine for up to 20 mm (3/4") solid wood banding. -- "QA 34 Quick Melt" Glue system per melt hopper feeder & roller applicator (reversible); pneumatic pressure roll section with (1) large dia. driven & (6) idle rollers. -- Workstations:Double motor front & rear end trim: 0.7 HP - 12,000 RPM Motor ea.; pneumatic chamfer setting. -- Top & bottom rough trims: 2 HP - 12,000 RPM motor ea. -- Top & bottom profile trim units: For leading & trailing edge, (4) 0.6 HP - 12,000 RPM motors; up to 4 mm edge thickness: All trim station motors are: 200 Cy - HF and equipped w/electronic brakes. -- Profile tracing from: Top, bottom and side for chamfering or rounding of pretrimmed PVC edges; pneumatically controlled blowing nozzles. -- Max. edge thickness: 3 mm (1/8"); panel thickness: 12 - 60 mm (15/32" to 2-3/8"); unit laterally adjustable by max. 50 mm (1-31/32"); Collection box for PVC shavings. -- Height adjustment with top pressure beam without tools; manually adjustable with digital mechanical counters. -- Profile Edge Scraping Unit with: Electropneumatic adjustment. -- Top & Bottom buffing unit. -- Feed & Holddown System:Motorized top pressure beam with powered V-belt holddown. -- 80 mm Wide Heavy-Duty feed chain w/rubber pads, automatic chain track lubrication system. -- 5 HP Feed drive for variable feed speed of 23 - 98 FPM. -- Operator & Machine Control:HOMATIC "PC 22", 2 GHz CPU with 512 MB RAM, USB port; functions in XP Windows environment. Keypad with TFT flat screen LCD display, onscreen fault diagnostic, part & lineal feet/meter tracking, etc. Diagnostic analysis from HOMAG via Modem fault diagnostic is possible. -- Complete with:SIKO Digital adjustments on: Top & Bottom trim, fine trim, and scraper stations; 10 KVA - 200 Cy frequency converter, electronic DC brakes on all trim motors. -- Sound cabins for all trim workstations; adjustable outboard panel support with floor supports. -- Actual Model is Optimat KAL 210/7/A20.S2.NOTE: Seller states that the Edgebander was in use until recently. The Corner Rounding stations are no longer in working condition

HOMAG - OPTIMAT KDF 440C: Special RH Feed Direction Edgebander w/Premilling, Corner Rounding & Return Conveyor (aka BRANDT - KDF 440C)Specifications: Premilling & Corner Rounding; HIGHFLEX Automated package. -- Edge & Workpiece Capacity: 0.4 - 8 mm (0.016 - 5/16") Edge; 8 - 60 mm (5/16 - 2-3/8") panel thickness; 160 mm (6-3/8") min. panel length; 70 mm (2-3/4") min. panel width.Equipped with: -- Premilling Station:(2) Motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip free & clean panel edges. Equipped with diamond cutterheads -- Infeed Fence with: Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between Glue roller and pressure section. -- Automatic Edge Magazine: Strip & coil stock; strips: 0.4 mm - 8 mm (0.016 - 5/16"); coils up to 3 mm PVC; "HD" guillotine "Quick Change" Glue Tank for maintenance & glue color change. -- Pressure Section: 1st Roller driven plus: (3) Idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable 8 - 14 MPM (26 - 46 FPM); 11 MPM (36 FPM) when using contour trimming. -- BRANDT "Power Touch Control"; memory: 256 MB RAM; 1 GB flash card drive; Operator control panel: 22" Color HD widescreen; soft keypad; internal modem for remote diagnostic link.Workstations -- End Trimming:(2) Motor @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit:Top/Bottom (2) motors; 0.55 kW (3/4 HP) - 12,000 RPM; auto. tilt positioning; 0° - 25° with combination flush/radius/chamfer cutterheads; horizontal & vertical tracing wheels. Equipped with: Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover. Includes: (3) Positioning options: Profile-1, Profile-2; flush trimming -- Corner Rounding Unit:(1) Motor: 0.35 kW (1/2 HP) - 12,000 RPM for leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness -- Scraping, multi-profile (PVC): Top/Bottom with (2) profiles. 1 mm & 2 mm or 3 mm instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels. - PVC scrape collection box. -- Scraping Glue Unit:Flush Top/Bottom on panel surface with floating insert knives. -- Buffing Unit: Top/Bottom (2) motors; 0.10 kW (0.125 HP) - 2,800 RPM. -- RIEPE anti-adhesion and RIEPE detergent. -- Complete with:Motorized, programmable hold-down pressure beam; padded sound enclosure and used tooling. -- Options Include:Homag Return Conveyor as pictured. -- Actual Model: RH Feed HOMAG - OPTIMAT KDF 440C (aka BRANDT - KDF 440C, but branded HOMAG).

HOMAG S-200 (OPTIMAT KDF 130C): Edgebander (w/Premill & Corner Rounding) +"AIR TEC" EVA/PUR. -- Specifications0.3 - 3 mm (0.016 - 0.11") Edge; 8 -60 mm (0.312 - 2.375") panel thickness; 160 mm (6.375") min. panel length; 70 mm (2-3/4") min. panel width. -- Equipped with:Separating/cleaning agent spraying units. -- Premilling Station: (2) Motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. -- 100 mm Dia. diamond cutterheads. -- Integrated heated glue roller. -- AirTec Reactivation unit for: Zero edge finish. -- Automatic Edge Magazine for: Strip & coil stock; up to3 mm PVC. -- "Heavy-Duty" Guillotine. -- EVA "Quick-Change" glue pot & roller application unit. -- Pressure Section. 1st Roller driven plus: (2) Idle rollers; timed pneumatic pressure controlled. -- Feed Speed: 8 MPM. (26 FPM). -- Operator InterfaceHOMAG "easyTouch" Operator Interface with: 7" Graphic color touch display & soft keypad; intuitive, user-oriented navigation. -- (20) Storable programs guarantee flexibility when processing a wide variety of edge materials and changing customer requirements. -- Clear overview of the help & assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Workstations End Trimming: (2) Motors each @ 0.35 kW (1/2 HP) 12,000 RPM; automatic chamfer from control panel 0° - 15°. -- Flush/Bevel-Fine/Radius Trimming Unit. (2) Motors: Top/Bottom; 0.55 kW (3/4 HP) - 12,000 RPM; 0° - 25° auto-tilt positioning from control panel with combination flush/radius/chamfer cutterheads. -- Includes (3) positioning options: Profile 1, Profile 2, & Profile 3: Flush trimming. -- Corner Rounding Unit. (1) Motor 0.35 kW (1/2 HP) - 12,000 RPM with: Automatic adjustment from control panel for: 1-Mil, 2-mil & 3-mil thickness. -- For leading & trailing edges, vertical corner rounding of panels: Ether radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, multi-profile (PVC) Top/Bottom with (2) profiles: (1) 1 mm, 2 mm, or 3 mm in place of (2) 2 mm positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Buffing Unit: Top/bottom (2) motors; 0.10 kW (0.125 HP) - 2,800 RPM. -- Complete withMotorized hold-down pressure beam; padded sound enclosure, isolation transformer for multiple input voltages, used tooling, and original factory documentation. -- Actual Model is: HOMAG EDGETEQ S-200 (OPTIMAT KDF 130 C)NOTE: Owner States "Our objective is to be completely transparent with potential buyers and clearly state that the equipment is being offeredas-is, currently dismantled and stored." Buyers seriously interested can arrange an inspection at our warehouse, in FL, as they sit, in storage.

HOMAG - EDGETEQ S-240: Edgebander (w/Premill & Corner Rounding)Specifications • Solid Strip & Coil Stock; 0.3 - 3 mm (0.016 - 0.11") • Workpiece width 70 mm = thickness 8 - 22 mm• Workpiece width 120 mm = thickness 23 - 50 mm• Standard Workpiece thickness: 8 - 50 mm / 1.96" max.)• Fixed Feed of 11 MPM (36 FPM)Equipped with • Premilling Station: (2) Motors @ 2.25 kW (3.0 HP) - 12.000 RPM, LH & RH rotation. Diamond cutterheads & pneumatic jump control for chip-free and clean panel edges. • Integrated heated glue roller.• Automatic Edge Magazine for Solid Strip & Coil Stock; up to 3 mm. • "Heavy-Duty" Guillotine for Solid Strip & Coil Stock; up to 3 mm. • "Quick-Change" glue pot & roller application unit. • Pressure Section. 1st Roller driven plus: (2) Idle rollers; timed pneumatic pressure controlled. Operator Interface • HOMAG "easyTouch" Operator Interface with: 7" Graphic color touch display & soft keypad; intuitive, user-oriented navigation. (20) Storable programs guarantee flexibility when processing a wide variety of edge materials and changing customer requirements. Clear overview of the help & assistant functions, including the glue pot temperature or troubleshooting in plain text.Workstations • End Trimming: (2) Motors, each @ 0.35 kW (1/2 HP) 12,000 RPM.• Top/Bottom Flush-Fine Trimming Unit: (2) Motors, each @ 0.55 kW (3/4 HP) - 12,000 RPM.• Corner Rounding Unit. (1) Motor, 0.35 kW (1/2 HP) - 12,000 RPM. • Top/Bottom Scraping, with vertical & horizontal copy wheels & PVC scrape collection box.• Top/bottom Buffing Unit: (2) motors, each @ 0.10 kW (0.125 HP) - 2,800 RPM. Complete with • Hold-down top pressure beam; padded sound enclosure, used tooling, and original factory machine documentation. • Actual Model: HOMAG EDGETEQ S-240 (aka: KDF 230)