GRIGGIO G 1100 Wide belt Sander2-Head, 1,100 mm (43") width cap. -- 1st Head: Rubber covered steel contact roll, duro 85, 220 mm diameter . -- 2nd Head: Rubber covered contact roll duro 50 -- 25 HP motor to drive both head. -- 43" x 85" abrasive belts, electropneumatic abrasive belt tracking, -- Conveyor belt feed, two speed from control panel at 15 and 30 FPM, 0.4/0.7 HP feed drive, automatic conveyor belt tracking, -- 1/8" - 6-1/2" motorized thickness adjustment with LED readout & 0.75Hp gearmotor drive. --Automatic positioning of the working table, rubber covered spring loaded pressure rollers, double infeed and outfeed rubber covered rolls, infeed panel "over-thickness" sensor. --Two suction dust hoods dia. 6" (150mm),

GRIZZLY H2934 2-HEAD WIDE BELT SANDER2-Head Wide Belt Sander, 36-1/2" width cap. -- Head configuration: - 1st Head: Rubber covered contact drum; 2nd Head: Combination head with rubber covered contact drum and adjustable platen; Abrasive belt size 37" x 60". -- 0" to 6" Thickness cap., LED digital depth encoder; 14" min. board length and 12" infeed conveyor. -- 1st Abrasive belt surface speed of 3,543 SFPM; 2nd abrasives belt surface speed of 2,554 SFPM. -- Conveyor speed from 14 - 60 FPM. -- 20 HP - 50/25 Amp Sanding motor; 1 HP - 3.4/1.7 Amp conveyor motor; 0.25 HP - 1.2/0.6 Amp table lift motor. -- Complete with: Rubber covered holddown rolls, adjustable felt platen, Amp/load meter, and disc brake for emergency stop.

GRIZZLY GO447 37" Dual Head Wide Belt Sander.37" Width cap. Drum, combination HeadHead Configuration1st Head: Contact Drum2nd Head : Combination Head. Rubber covered drive roll and adjustable platen; sanding belt size 37"" x 75"".Specifications -- 6" Thickness cap., LED digital depth encoder; -- 14" min. board length and 12" infeed conveyor. -- Min board thickness 1/4" -- 1st Head Abrasive belt surface speed of 3,543 SFPM; -- 2nd Head abrasives belt surface speed of 2,554 SFPM. -- Conveyor speed from 14 - 60 FPM. -- 20 HP Motor driving both heads -- 1 HP - 3.4/1.7 Amp conveyor motor; 0.25 HP - 1.2/0.6 Amp table lift motor.

HALSTY 136 WIDE BELT SANDER1-Head Sander with 36" width cap. and 6" thickness cap. -- Combination sanding head with 5-1/4" dia. contact roll, 2-1/2" wide polishing platen; 20 HP 3-Ph motor. 37" x 75" Abrasive belt, electronic tracking. -- Variable feed drive for conveyor belt with speeds of 0 - 18 FPM, 2" dia. infeed & outfeed rubber covered holddown rolls. -- 0" - 6" Thickness cap. with motorized adjustment via (4) 1" Acme thread jackscrews.

NOTE: Wide Belt Sander was completely rebuilt for $68,000 in 2019. 53" 4-Head Wide Belt Sander Head Configuration: 1st Head: Spiral rubber contact roll, 45 kW, 460 V; 2nd Head: Spiral rubber contact roll, 44 kW, 420/480 V; 3rd Head: Spiral rubber contact roll, 37 kW, 460 V; 4th Head: Platen design with (2) Smooth steel rollers; Final Station: Rotating air-jet blow-off; 12" Load space, Sensing, Abrasive belt size 1,400 x 3,250 mm (55.12" x 127.95"), T.B. WOODS "E-TRAC WF-2" Sensor-less vector drive for variable sanding head speed Vacuum feed mat, Adjustable fence, VACON Variable speed drive for feed speed, 8.6 kW, 254-277/440-480 V, Electronic belt tracking & Pneumatic motorized thickness control, Approximately 2 HP, 230/460 V HEESEMANN Swivel-mounted touchscreen control Overall dimensions: 164" x 92" x 112" H, Weight: 11,000 kg (24,250 Lbs.) NOTE: Machine is currently in storage.

54" 3-Head Orbital Sander, For abrasive belt cross-grain scratch removal with (3) Orbital Platen Heads & (1) Rotary Brush Head Configuration: 1st, 2nd, & 3rd Heads: Each with 5" W Platen, Dual orbital action, High-speed orbit on sanding pad with 3 kW (4 HP) Motor, Secondary oscillation with 1-1/2 HP Motor, "Quick-change" abrasive material, Inverter drive; Rotary Brush: 6" Maximum diameter, 3-1/2 HP Motor, Brush loading, Ionization bar for final fine dust collection Vacuum conveyor bed with 10 HP Blower motor, Inverter-controlled variable speed drive with 4 HP Motor & Variable feed speeds 15 - 66 FPM, Automatic conveyor belt tracking, Automatic parts thickness, with 1/8" - 4-5/8" Thickness range & Programmable height adjustment, (4) Screw jacks PC-based control, Windows XP, Touchscreen monitor, Infeed & outfeed spring-loaded hold-down rolls, Infeed hand safety stop, outfeed emergency stop, Digital motor load meters, High-efficiency dust extraction NOTE: Machine is currently in storage.

HEESEMANN - LSM 8, ...3-Head Wide Belt Sander53" Width cap. Crossbelt, Combination , and DrumHead Configuration:1st Head: Cross Belt Sanding Unit, 2-speed motor - 19/24 kW (26/33 HP). - Abrasive belt speed: 12/24 MPS (39/78 FPS); Cross Belt (Cloth), 4,800 x 150 mm (189" x 6").2nd Head: Combination Longitudinal Sanding Unit Front retractable roller for light calibrating and segmented pad system for fine sanding; bi-directional sanding; Door-in-Door viewing; 2 speed motor - 31/37 Hp, abrasive belt speed 10/20 mps (33/65 fps3rd Head: Longitudinal Sanding Unit Internal pressure segment belt for finer sanding Inner chevron belt; Inverter driven motor: 26 kW (34 HP); abrasive belt speed: 0.5-16 MPS (1.6-52 FPS); Longitudinal Belt: 2,620 x 1,350 mm (103" x 53").Unit 4: Panel Cleaning Brush, Fiber trimming.Specifications: -- HEESEMANN's LSM-8 Sanders are designed for heavy (2 - 3) shift operations; this Sander is ideal for: Whitewood sanding of veneered panels and panels coated with various sealers. -- The crossbelt removes tape, cuts short fibers that contribute to grain rising, and sands panels with "book-matched" veneer. -- The last sanding unit is equipped with an internal pressure segment belt for an extra smooth finish.Enhanced 16 mm control roller spacing with (3) rollers per segmented pad. -- CSD® Segmented pad system is equipped on all (3) sanding units. -- Pneumatic conveyor belt cleaning. -- Infeed extension with non-driven rollers. --Electronic variable feed speed from 5 - 25 MPM (16-82 FPM). --Workpiece thickness 3 mm - 140 mm (1/8" to 5-1/2").Equipped with & Features: -- Vacuum Table: Only HEESEMANN builds it into the frame for superior holddown! -- Industrial PC controller, Windows® Operating System.Width Capacity: 53"

HEESEMANN LSM-8/3-OSR Wide Belt Finishing Sander, 52" and (3) Heads; Equipped with: (1) longitudinal segmented platen head. and (2) Orbital Platens -- 1st Head: Longitudinal segmented platen head. Segmented Polishing Platen, 20 & 27 HP dual speed motor. electronically controlled segments to conform to panel size,.2620 x 1350 mm (91.4 x 53.2") Sanding belt. - Equipped with HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 16 mm (5/8") sense part configuration; pressure for each segment, to eliminate sand through, can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. The "CSD" computer control will hold a maximum of (20) programs. -- 2nd & 3rd Heads: OSR Dual orbital action head with (1) high-speed orbit on sanding pad, powered by 3 kW (4.5 HP) motor.Secondary oscillation movement of platens powered by 1.5 HP motor. Upstream and downstream vacuum chutes on each head for dust localized dust pickup.- Platens feature "quick change" abrasive material; Both orbital heads with variable speed inverter drives. -- Outfeed Rotary Brush with cleaning brush loading with single end adjustment , 6" max. dia., 3.4 HP motor. -- Variable feed speed from 13 to 82 FPM, 6.5 HP feed drive. -- Infeed and outfeed Ssissor Lift and Control box shown are not included. -- Motorized thickness opening 1/4" to 3-5/32" max. - -- Power Consumption: 63 KW, 75 Amps. -- Separate display console for CSD control.

HEESEMANN - LSM 8-5 RRRL, ...53" Wide Belt Sander53" Width cap.: Drum, Drum, Drum, and CSD® Pad.Head Configuration:• Unit 1 - Longitudinal Sanding Unit: Steel contact roller, helically grooved. - Single-speed 48 HP motor, electronic braking.• Unit 2 - Longitudinal Sanding Unit: Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking.• Unit 3 - Longitudinal Sanding Unit:- Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking, bi-directional drive.• Unit 4 - Longitudinal Sanding Unit: CSD® Segmented pad system, 2-speed 20/26 HP motor, electronic braking.• Unit 5 - Panel Cleaning Brush: Fiber trimming, 2.3 HP Motor.Specifications: -- Working height: 880 mm (34.64"). -- Workpiece thickness: 3 mm to 150 mm (1/8" to 6"). -- Working width: 1,300 mm (51-1/8"). -- Longitudinal belt: 1,350 x 2,620 mm (53" x 103"). -- Machine voltage: U.S. Electrics 480 Volts, 3-Phase, 60 cycles.Constant Pass LineController: -- Industrial PC. -- TFT Color touchscreen. -- Windows® Operating System. -- (100) Memory addresses for: • CSD® sanding pressure. • Sanding start/stop. • Sanding belt speeds. • Grit sequence indication. • Sanding belt selection - "ON/OFF". • 1-Button sequenced starting for all motors.RS-232 Serial port.RJ-45 LAN Port.Modem with software licenses.For All additional, detailed specs, select the "View Literature" link .

HEESEMANN MFA-6 Wide Belt Sander with (3) Heads and a Cleaning Brush.Basic Working Capacity: Max. working width is 1,350 mm (53"), thickness opening min./max. is 3 mm - 150 mm (0.118" - 6.0"). - Conveyor belt speed variable from 5 - 15 MPM (16 - 49 FPM); constant pass height of 880 mm (34.65").Features: -- Head Configuration: (2) Steel contact drum heads, (2) "CSD" controlled contact platens, and (1) rotary cleaning brush. -- Belt Handling: Broken belt monitor and automatic infrared belt tracking; intermittent pneumatic belt cleaning device, belt access on the left-hand side. -- Conveyor Belt: High powered vacuum holddown by 8.6 kW (11.5 HP) fan drive motor, automatic vacuum monitoring system. Variable speed by inverter from 5 - 15 MPM (16 - 49 FPM). -- CSD-32 System: Heads #3 & #4 are equipped with HEESEMANN's Patented "Segmented Pad System", Computer Selective Pressure Control from 0 - 150%, precise surface & edge pressure control, edge pressure independent of surface; 2 mm thickness compensation - zero maintenance with sealed enclosure.Sanding Head Configuration: -- 1st Head: Steel Contact Roll, 8" dia., 25.3 kW (34 HP) motor; sanding belt size of 2,150 mm x 1,400 mm (85" x 55"); belt speed is 18 MPS (60 FPS); equipped with belt motor brake. -- 2nd Head: Steel Contact Roll, 8" dia., 17.5 kW (24 HP) motor; sanding belt size of 2,150 mm x 1,400 mm (85" x 55"); belt speed is 18 MPS (60 FPS); equipped with belt motor brake. -- 3rd Head: Sanding Platen, electronically controlled pressure segments to conform to panel size, 17.5 kW (24 HP) motor; sanding belt size is 2,150 mm x 1,400 mm (85" x 55"), belt speed of 18 MPS (60 FPS); equipped with belt motor brake.. -- Cleaning Brush: Outfeed Rotary Panel Cleaning bristle brush, 120 mm (4-3/4) dia., 0.9 kW (1.2 HP) motor, and holddown roller. -- Includes: Outfeed conveyor table, 48" width x 80" length. Large batch of sanding belts.Controls: -- LCD Operating Panel with: Touch-screen and graphical display, (20) memory addresses for sanding head selection, thickness opening, conveyor feed speed, 1-button sequenced starting of sanding motors, and tracking of sanding belt usage. -- Operating Requirements: Electrical is 151 Amps @ 460 Volt; Dust Extraction is 5,800 CFM @ 3" static pressure. Machine weight approx. 7,000 kG (15,500 Lbs). -- Complete With: Extended infeed table with (2) idle rollers, interior lights, emergency and oversize part thickness safety bar, and Manual.

---In Auction---NO RESERVE---Good Condition--- HEESSEMANN DBV 1 2,300 mm (90.55") 2-Head Cross Belt Automatic Stroke Sander Specifications: - Sanding length 2,300 mm (90.55"). - Sanding Belt size 150 x 8,500 mm (5.91" x 334.65"), Pressure belt length 6,750 mm (265.75"), V-Belt size 10 x 900 mm (0.39" x 3.43"). - Max. thickness 8". - Sanding belt speed 82 FPS. - Feed speeds 9 - 50 FPM. Equipped with: - (1) Rough sanding & (1) Fine sanding cross belt heads, with Limit switch-controlled pneumatic pressure plates with Timer, Dubbing control on fence side, Adjustable dubbing unit on right side, & 25 HP Motor. - 90” W x 5-1/2’ L Conveyorized feed table, with Multiple 5" W conveyor belts, Automatic tracking, & Motorized thickness adjustment. - Overhead hold-down rollers. Complete with: - 4" W Brush belt brush-off device. - Dimensions of Control Console: 40" x 21" x 56" H Details, Photos, Videos, Bidding: https://exfactoryauctions.com/Detail/SS-230669/event/A051324$1

HEESEMANN MFA-8 D Wide Belt Sander (4) Heads; 53" Width cap. Veneer/ Sealer Sanding Wide Belt.Great Lacquer/Sealer sander with: (2) Segmented polishing platen, (2) Orbital heads, (1) De-nibbing/Polishing brush.Head Configuration: Head 1: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 2: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 3: Orbital head with composite/dense fiber loading; 5HP motorHead 4: Orbital head with composite/dense fiber loading: 5HP motor(1) Brush Type head for de- nibbing and polishingSpecifications: -- LCD monitor with graphic display and key pad entry, 20 program capacity, -- Pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required.Equipped with & Features -- Air blast abrasive belt cleaner on heads 1 & 2. -- Variable feed speed from 10 to 49 FPM via 2 HP feed drive. -- Motorized thickness opening 1/4" to 3-5/32" max. -- Rubber covered Infeed and out feed holddown rolls.

Holytek 37DA Wide Belt Sander (2) Heads37" Width cap Drum, Combination Head1st Head: 7" Dia. spiral grooved rubber covered contact roller, 20 HP motor;2nd Head: Combination sanding head with 5" dia. spiral grooved rubber covered contact roll & 2" wide polishing platen, 15 HP motor.Specifications -- Abrasive belt size of 37" x 60" -- Pneumatic belt tensioning and electronic abrasive belt tracking -- 12" min. working length. -- 2 HP Conveyor belt motor, -- Variable feed speed from 13 - 52 FPM,Equipped with & Features -- Infeed & outfeed rubber covered holddown rolls; -- 0" - 4" motorized thickness adjustment by 0.5 HP motor. -- Safety stop bar, emergency rail stop across the front of conveyor -- Motor load meters.

HOLYTEK MHB 242 Top/Bottom Wide Belt SanderHeavy-duty and powerful double surface sander providing significant time saving and improved productivity.Smooth and quiet oscillation. Belts oscillation controlled electronically by an infrared system which resists dust.Pneumatic sanding belts tensioning ensuring fast and easy belt replacement.Independent motor for each sanding belt.Pneumatic disc brake system automatically activated if power supply is interrupted, thus preserving the sanding belts from being damaged. Top and bottom 24" wide belt sanderFeatures: -- Spiral grooved 8" (D) rollers (R) and 3-1/2" (D) rollers (K) keep the sanding belts cool. -- Sanding belts: 75" Long. -- Elevation of table with digital readout and activated by independent motor. -- Control panel with: Ammeters indicating main motors current. Specifications: -- Upper Drum motor: 15 HP; 600 V; 60 Hz - 3-Ph. -- Upper Combination head motor: 10 HP; 600 V; 60 Hz - 3-Ph. -- Lower Drum motor: 15 HP; 600 V; 60 Hz - 3-Ph. -- Lower Combination head motor: 10 HP, 600 V, 60 Hz - 3-Ph. -- Feeding motors: 2 HP (x2). -- Table elevation motor: 0.5 HP. -- Electrical intensity: 53 A. -- Drums: 8" (D) - 75 DUROS. -- Max. working width: 24". -- Min. working length: 13-3/4". -- Working thickness: 3/16" ~ 5" -- Sanding belts dimensions: 25" x 75". -- Variable feeding speed: 8 - 16 MPM. -- Dust hoods Top: 4 x 4"(D); Bottom: 3 x 4"(D). -- OAL 127" x 70" x 75" high. -- Weight: 9,460 Lbs.

HOLYTEK - KL-36PC, ...2-Head Sander 2-Head Planer Sander 36" with planer head & combination head.Description: -- Planing head (P) of a 6'' dia. made of steel with spiral design for heavy stock removal. 228 TCT Tips: 15 x 15 x 2.5 mm each disposed on (6) rows. Each knife has (4) usable cutting edges. Easy access to planing head for tips rotation or replacement. -- Precise dial indicator showing the exact positioning of the sanding pad. Quiet & smooth oscillation! Pneumatic oscillation system controlled electronically by an infrared system, which is not affected by dust. -- Combination Head (1 drum & 1 sanding pad) (C) for superior quality of finishing. A sanding belt with a grit of 120 or 150 allows a finishing sanding in a single-pass. -- Elevation table: (4) Screws. -- Infeed roller table extension 15 3/4" -- Outfeed roller table: 15-3/4" with (2) Rollers. -- Centralized Control Panel with: Electronic digital readout (Metric or Imperial) for elevation. Precise positioning at the elevation requested. -- Ammeter indicating the electrical intensity on the spiral cutterhead and the combination head motors. -- Electrical box with: CSA Approved electrical components ensuring maximum dependability and an outstanding long-lasting performance.Specifications: -- Spiral cutterhead motor: 20 HP, 600 V, 60 Hz, 3 Ph -- Combination head motor: 15 HP, 600 V, 60 Hz, 3 Ph -- Table elevation motor: 0.25 HP, 600 V, 60 Hz, 3 Ph -- Feed motor: 2 HP, 600 V, 60 Hz, 3 Ph -- Spiral cutterhead dia.: 6'' -- TCT Tips dim.: 15 x 15 x 2 mm (228), (6) rows -- Max. working width: 36" -- Min. working length: 12" -- Max. working thickness: 5" -- Sanding belt dim.: 37" x 75" -- Dust hoods dia.: 4'' x 2 & 5" x 2 -- Machine dim.: 71" L x 76" W x 77'' H -- Net weight: 1,450 kG or 3,190 Lbs.

HOUFEK BULDOG 1100-RC Wide Belt Sander, (2) Head 2-Head, 43" width capacity Wide Belt Sander with Drum & Combination Head.Head Configuration:1st Head: 6" Dia. rubber-covered contact roll with 20 HP Motor.2nd Head: Combination Head, rubber covered contact roll 6" dia. with 15 HP Motor. The HOUFEK Twin Head Wide Belt Sander is intended for users who require high-quality value and maximum performance. Ideal for calibration and sanding of solid wood, calibration of boards (MDF, hardboards, joint boards) and also sanding of veneered surfaces.Specifications: -- Max. operating width 1.100 mm (43") -- Operating height max./min. 160 mm - 3 mm (0.12" - 6.3") -- Sanding belt dimensions 1,120 mm x 1,900 mm (44" X 75") -- Sanding belt speed 18 m/Sec (3,550 FPM) -- Feed speed 4,5 or 9 m/Min (15 or 30 FPM) -- Main motor power (2 x 11 kW) -- Feed motor power 5.5 kWEquipped with & Features: -- Motorised rise and fall of table, complete with Automatic start switch. -- Oscillation of abrasive sanding belt controlled by infra-red eye. -- Digital display indicator for table opening position. -- Automatic measuring of material height. -- Dual-speed feeding of material. -- Soundproof protection. -- CE electrical and safety standards.Note from the seller: Only selling to make room for a 3-head 53" machine. In operation using daily. Available last week of July, first week of August.

HOUFEK 1100-RC Wide Belt Sander, (2) Head, 43" capacity: 2-Head 43" width capacity Wide Belt Sander with Drum & Combination Head.Head Configuration: -- 1st Head: 6" Dia. rubber covered contact roll with 25 HP Motor. -- 2nd Head: Combination Head, rubber covered contact roll 6" dia. with 20 HP Motor. The HOUFEK Twin Head Wide Belt Sander is intended for users who require high quality value and maximum performance. Ideal for calibration and sanding of solid wood, calibration of boards (MDF, hardboards, joint boards) and also sanding of veneered surfaces.Standard Features: Motorised rise and fall of table, complete with Automatic start switch. -- Oscillation of abrasive sanding belt controlled by infra-red eye. -- Digital display indicator for table opening position.Additional Features: -- Automatic measuring of material height. -- Dual-speed feeding of material. -- Sound proof protection. -- CE electrical and safety standards.Specifications: -- Max. operating width 1.100 mm (43") -- Operating height max./min. 160 mm - 3 mm (0.12" - 6.3") -- Sanding belt dimensions 1,120 mm x 1,900 mm (44" X 75") -- Sanding belt speed 18 m/Sec (3,550 FPM) -- Feed speed 4,5 or 9 m/Min (15 or 30 FPM) -- Main motor power (2 x 11 kW) -- Feed motor power 5.5 kW.

INDIANA Model 12 Edge SanderDouble Sided, Non-oscillating Edge Sander with 48" x10" platens. -- 3 HP 220/440 Volt, 3 Phase Motor -- 56" X 10-3/4" Tilting Side Tables, 27" X 18"end Table, and Hand Wheel adjustment for table height. -- 9" belt capacity.This Heavy-Duty Sander has been Cleaned and Checked, and is available for immediate delivery!

Oscillating Edge Sander: 1 1/2 HP, 6" x 89" Belt Size (In.), 4,000 SFPM Belt SFPM, CordedFor edge, face, bevel, and contour applications. Oscillating feature reduces heat build-up. Quick-release lever and control dial help track and replace belts. Cast-iron table moves up or down.Specifications: 1-1/2 HP, Hz60, Amps AC18/9, Belt Size 6" x 89", Belt SFPM 4,000, Table Work Surface 32" x 7", Dust Collection Port Size 4" Features: -- 4 in Dust Port Hooks Up to Your Dust Collection System for Efficient Dust Removal, adjustable outer drum, support table enables contour sanding. -- Cast Iron table moves up or down to provide exact work piece positioning, Graphite covered Platen runs cooler increasing machine and belt life. -- Oscillating feature reduces heat build up on sanding belt, Quick Release Lever and Tracking Control Dial are conveniently located for replacing and tracking belts, Tilting Sanding Head for sanding bevels.

JET EHVS-80 6"; x 89" Non-Oscillating Horizontal/Vertical Edge SanderSpecifications: -- Table size 12-1/2"; x 37"; x 3/4"; Thick, Table tilt 0° - 90°. -- Platen size 7" x 34". -- Belt speed 3,900 SFPM.Equipped with: -- 6" x 89" Abrasive belt. -- 1-1/2 HP 3,600 RPM Direct drive motor.Palletized Dimensions: 50" x 31" x 44" H.