D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

SCM DMC 90 RCS 135 2 Head 53 inch Wide Belt Sander 53" Width cap, Steel Drum, Combination HeadHead configuration1st Head: Steel Drum 36 HP Motor, 9" Diameter 2nd Head: Combination head 65 shore drum and solid wood platen, 30 HP Motor, 7" Dia. drumSpecifications: -- 54" x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computer controlled; set-up functions with a keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, -- Motor load meters. -- 2-Roll infeed conveyor extension; -- High-efficiency dust extraction.NOTE: Specs have to be verified

DMC UNISAND K 1100 Wide belt sander4-Head, 43" (1,100 mm) max. width cap. Head sequence: (3) Contact rolls and (1) Combi with roller and segmented platen.Heads configuration: -- 1st Head: Helical grooved steel contact roll, 10" dia., 48 HP motor. -- 2nd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. and 65-Shore covering hardness, 35 HP motor. -- 3rd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. 45-Shore covering hardness, 30 HP motor. -- 4th Head: Combi head with roller covered with rubber, 30 shore and Finishing sanding pad unit , 30 HP 2-speed motor with segmented pads pneumatically controlled -- All heads use 44" x 103" (to be confirmed) abrasive belts and are equipped with electronic tracking, automatic tensioning, automatic emergency breaking, and oscillating sanding belt cleaners.Controls: -- "HYDRA V-PAD" 10" Touch-screen computer for setup functions, color LCD Display, allows operator to setup/recall part thickness, -- Conveyor feed speed (3.5 - 18 MPM), -- Abrasive belt direction, and reversible speed setting of 4th head. -- Conveyor belt feed with inverter control, feed speeds from 11 - 60 FPM, 5.5 HP feed drive; -- Infeed & outfeed holddown pinch rolls on all heads, automatic part thickness setup with the moving feed belt, -- 2-speed motorized part thickness adjustment, 1/8" - 6" max. opening; -- Infeed & outfeed motorized conveyor extension rollers, automatic part thickness setup sensor. Complete with: -- Safety stop at infeed, -- Anti-kickback device, -- Infeed & outfeed emergency stops, -- Motor load meters, i -- Infeed & outfeed idle rollers, -- High efficiency dust extraction, and control console with monitor.Note: (spare parts not installed) New feed belt , new front pressure roller, new front pressure bar and several new small parts for approx $15,000 of value +11 boxes (approx 5 belts/ box) sanding belts 100 grit, 120 grit, 180 grit and 220 grit.

D M C EUROSAND L ERL 1350 M4 ...53" Wide Belt Sander with (4) Sanding Heads: 1,350 mm (53") Max. working width, equipped with (3) Contact Rolls, and (1) "Superfinishing" Segmented Platen Head.Head Configuration: -- 1st Head: Steel Contact Roller, spirally grooved, 250 mm (9.8") diameter; 26 kW (35 HP) motor. Pneumatically operated grit compensation. -- 2nd Head: Rubber Contact Roller, spirally grooved, approx. 85° Shore hardness, 250 mm ( 9.8") diameter; 22 kW (30 HP) motor. Pneumatically operated grit compensation. -- 3rd Head: Rubber Contact Roller, spirally grooved, approx. 45° Shore hardness, 250 mm ( 9.8") diameter. 3-speed motor 12 / 15 / 17 kW (16 / 20 / 23 HP). Pneumatically operated grit compensation. -- 4th Head: "Superfinishing" Segmented Polishing Platen with inner Chevron belt. With "PE 45 EPICS" (Electronic Pad Independent Control Stroke) - electronically controlled, segmented pressure pad with (45) pneumatically activated segments, each 30 mm (1.2") wide. The EPICS-system allows imperfections in the panel of up to 2 mm (1/16"). Driven by 2-speed motor 15 / 18 kW (20 / 25 HP) motor. -- 5th Position: (2) Oscillating Air Jet blowers for panel cleaning.All heads use abrasive belt size 2,620 x 1,370 mm (103" x 54"), and are equipped with electronic abrasive belt tracking, and pneumatic belt tensioning. Feed System with 900 mm (35-7/16") Constant pass line: -- Vacuum bed assembly to ensure flatness of parts and feeding of small & lacquered panels. -- Variable feed speed 4 - 19 m/Min (13 - 62 FPM), with 7,5 kW (10 HP) feed motor. -- Motorized thickness opening 4 to 170 mm (3/16" - 6.7") and Automatic thickness adjustment. -- Pneumatically operated conveyor belt tracking. Holddown shoes for the first three heads, rubberized rollers in the platen area.Machine Management System: -- Front-mounted control console with B&E "HYDRA V-PAD" 17" colour touch-screen monitor. NC-computer control and management of all machine functions. Storage capacity for (120) different sanding programs. -- Sanding heads with computer setup and adjustment, light indication of panel movement, thickness, and features maintenance indicator.Complete with: Roller table extensions front & back (28" each), Emergency stops front & back, Load meters, oversized parts and infeed protection. Includes dust extraction manifold. CE Compliant - Approx. weight 11,000 Lbs (5,000 kG)Actual model is D M C EUROSAND L ERL 1350 M4 ... Wide Belt Sander with (4) Sanding HeadsSander Dimensions: 160" x 80" x 90" H.Blowers Dimensions: 39" x 24" x 66" H.

DANCKAERT - 44 , ...ResawAir Strain 44"; x 5"; Bandsaw.Features & Specifications: -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to prevent spikes). -- Infeed & outfeed systems are the same. -- 24 ft. Long Camel Back chain (has air bags that are controlled by photo cell to raise & lower and index 1-board at a time). -- Max. length of lumber: 24 ft.From Seller: "The machine has a new VFDD 100 HP and a new WEG Severe Service 60 HP motor. All new hydraulic motors, caramel back chain, and roll cases."NOTE: Needs hydraulic unit.

Approximately 225 Linear feet of floor mounted monorail track (See attached layout drawing) , center link chain with 2-wheel trolleys at 32" on center, encased in 3" channel iron; outside rails with gravity rapid wheels at 8" on center, 3 1/2" channel iron legs 21" high, 54" on center. Includes: Motor drive, controls and (40) 32" X 72" metal pallets.SOME OF THESE SPEC ARE GENERIC BUT OVERALL REPRESENTATION OF THE LINE IS CORRECT.

Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. -- Specifications:3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG. -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Complete Over-all Foot Print 175’ long x 50’ wide

DEKKER VMAX 40 HP VACUUM PUMP (LIQUID RING): 40 HP Oil sealed, liquid ring, compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design, small footprint, patented, high efficiency "DX-5" separator eliminates oil carry over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant.Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation.Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct Drive and with:Low speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

DEKKER VMAX 40 HP VACUUM PUMP (LIQUID RING): 40 HP Oil sealed, liquid ring, compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design, small footprint. -- Direct Drive with:Low speed (1,750 RPM) Air cooled design &low operating noise level eliminates the use of V-belts, resulting in very low maintenance and zero downtime over the full vacuum range without overheating.

DEKKER - VMAX 40 HP: Vacuum Pump (Liquid Ring)40 HP Oil sealed; liquid ring; compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design; small footprint; patented; high efficiency "DX-5" separator eliminates oil carry over concerns; Engineered for continuous operation. -- Extended lifeSeal fluid is not used as a lubricant.Change interval is not critical, resulting in a min. of (10,000) Hrs of continuous operation.Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct Drive & with:1,750 RPM Low speed: Eliminates use of V-belts, resulting in very low maintenance & zero downtime.Over the full vacuum range without overheating.Air cooled design & low operating noise level.

DEKKER VMAX 40 HP VACUUM PUMP (LIQUID RING): 40 HP Oil sealed, liquid ring, compact motor mounted Vacuum Pump System; 550 CFM; max. 29" Hg. -- Heavy-Duty ConstructionCompact design, small footprint, patented, high efficiency "DX-5" separator eliminates oil carry over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant.Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation.Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct Drive and with:Low speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

Delta RC-63N 24" PLANER WITH SPIRAL CUTTER HEADSpecifications -- 24" x 9" Cap., 5/16" max. material removal, -- 10-1/2" min. part length. -- 15 HP Belt drive motor, -- Spiral Cutting Head -- 5,000 RPM, variable feed speed from 20 - 60 FPM.Equipped with & Features -- Powered raise and lower of 25" x 35" table, -- Sectional chipbreakers, sectional infeed roller & dual outfeed rollers. -- Push button magnetic control, -- Dust hood, & grinding attachment to sharpen helical head knives while on the machine.

DELTA RC-51 PLANER20" x 9" Cap., 7.5 HP motor, 4-knife cutterhead, power raise-and-lower adjustment and fine adjustment thru a convenient hand wheel; variable feed speed 16 - 28 FPM; equipped with sectional chipbreakers, adjustable bed & dual outfeed rollers. Actual model 22460

DELTA - UNISAW: Table SawSpecifications -- 10" Blade dia.; 3 HP - 3,450 RPM motor belt drives 5/8" dia. arbor @ 4,000 RPM; arbor tilts: 0° - 45°. -- 3-1/8" Max. depth @ 90°; 2-1/8" max. depth @ 45°; 25" max. rip cap. to right of blade & 15-1/2" max. to left of blade; 13/16" max. dado width. -- Includes: 27" x 40" Cast iron table; distance front edge of saw to blade 12-1/4"; 34" table height; DELTA Rip Fence; (1) set of dado blades.

DELTA 11-990C 12" 5-Speed Bench-Top Drill PressSpecifications: -- Table size 8-1/2" x 8-1/2" with 15-1/2"; x 40"; x 11/16"; Thick Plywood top, Table tilt 40° Left/Right. -- Base size 8-1/4" x 8-1/4". -- Quill travel 2-3/8", Chuck capacity 1/2", JT33 Spindle taper. -- Spindle speeds 620, 1,100, 1,720, 2,340, & 3,100 RPM.Equipped with: -- 1/3 HP - 1,720 RPM Motor.Complete with: -- Portable Wood Cabinet.Dimensions with cabinet: 41" x 36" x 57" H

DELTA UNISAW 10" Tilting Arbor Table SawSpecifications: -- Table size 20" LR x 27" FB x 34" H with 8" Left & Right Cast-iron table extensions, Table tilt 45° Left. -- Arbor dia. 5/8". -- Max. depth of cut: 4-1/8" at 90° & 2-1/8" at 45°. -- Max. dado width 7/8". -- Rip cap.: 52" Right & 12"; Left.Equipped with: -- 5 HP - 3,480 RPM - 230/460 V TEFC Motor.Complete with: -- Rip Fence. -- Blade guard.

DENRAY 2872 B Down Draft Sanding TableThis model is great for medium sized jobs, and can be used for plastics, woods and finishing materials. The 2872B comes with 80/20 cartridge filters which clean with a 99.95% capture rate at .5 micron. This model comes standard with Denray's "Jet Pulse" push-button cleaning, rubber coated top, along with motor access on the left end and filter access on the right end.Large work surface on this 28" x 72" table with DENRAY'S Pulse Jet Cleaning System. -- Rated at 3,000 CFM, after filters, with 2 HP motor and magnetic starter. -- Space-saving self-contained unit w/built-in dust drawer. -- High efficiency cartridge filters (180 sq. ft. of cloth area) that clean dirty air to .5-micron. -- Includes: Push Button cleaning -- Quiet operation at only 74 dBA sound level. -- Comfortable 36" working height. -- 3/4" Thick steel-reinforced MDF board worktable with "non-marring" rubberized surface. -- This machine can be used in heavy wood, finishes, solid surfaces and stone type materials. -- Available options: -- Explosion Proof Motor (3 Phase only). -- Light Bar. -- Casters. -- Auto-timer. -- Muffler (reduces sound level 10-12 dbs.). -- 100% Spunbond Polyester FiltersCarbon Filter Bank (odor only). -- HEPA Filter bank. --Three-sided Hinged Safety Shield. -- Magnehelic Gauge. -- HDPE Plastic Tabletop. -- Hydraulic Height AdjustmentAlso available in 230V, 460V and 575V 3 Ph..

DENRAY 2872 G Downdraft Sanding Table for Metal GrindingDenray grind downdraft tables are made for the general grinding of ferrous metals and come equipped with water pans built over the filters to help protect them from hot sparks. The flame-retardant 100% Spunbond polyester cartridge filters clean to .5 micron. These tables come equipped with Denray's "Jet Pulse" push-button cleaning, which can be set with an automatic timer.Includes: -- 28" x 72" Table top work area. -- 36" Work height. -- 3 HP motor w/ 3,600 CFM. -- 18" Fan. -- 76 Decibels Sound Level. -- Auto-timer. -- Magnehelic Guage Available Options: -- Explosion Proof Motor (3 Phase only). -- Light Bar. -- Casters. -- Muffler (reduces sound level 10-12 dbs.). --Carbon Filter Bank (odor only). -- HEPA Filter bank. -- Fiberglass Grate top. -- Rubber Mat for Steel Tabletop. -- Stainless Steel Tabletop. -- HDPE plastic tabletop. -- Hydraulic Height Adjustment. -- Smoke Arm. -- Larger Motor/Fan Up-grade?

DENRAY 3660B Down Draft Sanding TableConvenient 36" x 60" table with a 36" working height with DENRAY's Pulse jet Cleaning System. -- Rated at 3,400 CFM for fast, easy removal of dust. -- 2 HP 3-phase motor. -- Space-saving self-contained, double filtration unit with integrated table top surface filter and bottom filters on all (4) sides. -- No duct work, no loss of conditioned air. Sound level 74 dBA. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board with rubberized surface. -- Also available in 115 V and 220 V single phase