EXTREMA - XP-126A: Planer with Helical Head26" x 11-3/4" Cap.; 5/16" max. material removal; 10-1/2" min. part length; 20 HP WESTINGHOUSE / TIKO belt driven motor; STEALTH helical carbide insert cutterhead: 6,000 RPM; variable speed feed: 20 - 75 FPM. -- Equipped with: Powered raise-and-lower of 27" x 35-1/2" table; digital thickness controller; sectional chipbreakers; sectional infeed roller & dual outfeed rollers; (2) adjustable bed rollers.

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 Volt / 3 Phase.

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

Extrema WS-110 Single Spindle Shaper -- 3/4" & 1" Interchangeable spindles. -- 3 HP Single Phase, 3,450 RPM motor designed for operation in most smaller shops -- Belt drive for spindle speeds of 8,000 & 10,000 RPM _ 2-5/8" capacity under the nut (3/4" spindle) and 3-7/8" vertical spindle travel will accommodate a variety of cutters. -- Large Table size 28" x 30" with a 6" max. dia. table opening -- Includes Fence assembly, miter gauge, 1/2" collet adapter, and power feeder.

EXTREMA 126TV Single Sided Planer;26" Max. width capacity, 11.75" thickness, Solid cast iron construction. -- Precision ground cast iron table with motorized programmable height adjustment; 1/2 HP elevation motor. -- 20 HP Main drive motor -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- 1 HP Feed drive, variable feed speed setting from 20 to 75 FPM. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers; (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch and Emergency stop. -- Includes Operations manual, parts list & tool kit.

EXTREMA XP-124TV Single Head PlanerSpecifications: -- Solid cast iron construction. -- 15 HP Main drive motor, 1 HP feed motor 20 to 70 FPM, 1/2 HP elevation motor. -- Precision ground cast iron table w/motorized programmable adjustment. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" insert cutterhead with (4) sided inserts. -- Fixed feed speed setting for consistent stock removal. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers.Features: -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor. -- Magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit. -- Options: Single-phase power, please add ...$ 100, 460 volt add...$ 150.

EXTREMA XP-610 SINGLE SIDED PLANER24" Width capacity, 8-3/4" thickness, solid cast iron construction. -- 10 HP main drive motor -- Precision ground cast iron table w/motorized height adjustment, with digital thickness display; 1/2 HP elevation motor. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- Variable feed speed from 20 to 42 FPM; 1 HP feed drive. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

FARR GOLD - GS4, ...Dust/Fume/Material Collector: 3,000 CFM Rated cap., 1,300 sq./ft. filter area from (4) cartridge filters, approx. 2.3:1 air: cloth ratio. -- Equipped with: 5 HP Pull through motor; dirty air is pulled into the filter area at bottom of filter media section allowing gross dust particles to fall into Collector Barrels located beneath pyramidal Hopper discharging to a sealed Drum (not included). -- Fine dust is pulled up through the Cartridge Filters; dust Filter Cartridges are cleaned by automatic pulse jet with minimum compressed air consumption; cleaned air continues through Blower and is returned to the building Air Supply though a Silencer. -- Includes: Hopper with slide gate discharging into a sealed Barrel (not included), electrical control panel, support stand with clearance under hopper, discharge for a waste bin/drum.

FARR GOLD GS4 DUST/FUME/MATERIAL COLLECTOR: 3,000 CFM Rated cap., 1,300 sq. ft. filter area from (4) cartridge filters, approx. 2.3:1 air: cloth ratio . -- Equipped with: 5 HP Pull thru motor; dirty air is pulled into the filter area at bottom of filter media section allowing gross dust particles to fall into collector barrels located beneath pyramidal hopper discharging to a sealed drum (not included) -- Fine dust is pulled up thru the cartridge filters; dust filter cartridges are cleaned by automatic pulse jet with minimum compressed air consumption; cleaned air continues thru blower and is returned to the building air supply thru a silencer.. -- Includes: Cyclone with slide gate discharging into a sealed barrel (not included), electrical control panel, support stand with clearance under hopper, discharge for a waste bin,. access door, some pipe as pictured.

FELDER FORMAT KAPPA 450 Sliding Table SawSpecifications: -- 126" (3,200 mm) cutting length w/scoring, anodized 14-3/4" x 126" aluminum sliding table with tracking by roller bearings, locks for easy panel loading in any position; 450 mm dia. main saw blade. -- Motorized raise, lower, and tilting (0° - 45°) of the blade with digital readout. Equipped with: -- 7.5 HP Main motor, 1.0 HP scoring motor unit w/external adjustment; square crosscut fence with (2) stops, standard rip fence with 1,250 mm (49") rip cap. w/digital readout; extension table with miter fence, and sliding outrigger support. Includes: -- (2) 4" Dia. dust outlets; swing away overarm saw guard.Also available for an extra fee - 30 KVA, 208 to 380 Volt Three-Phase Transformer.

FELDER FORMAT4 PROFIT H08 16.31 FLAT TABLE MACHINE (W/ATC) -- Specifications5' x 10' "MATRIX" Phenolic Flat Table design for "Nested Base" Manufacturing. -- Working Capacity"X" Axis is 145" (3,683 mm); "Y" axis is 60.2" (1,530 mm);"Z" axis stroke is 11.8" (300 mm); max. material thickness is 4.3" (110 mm). -- Positioning Speed"X" & "Y" Axis at 197 FPM (60 MPM); "Z" axis is 49 FPM (15 MPM). -- WorktableThe working area is subdivided into (8) vacuum fields (H08 16.31) to ensure the best holding force for the most varied board sizes. The vacuum fields are controlled manually by means of hand levers on the front side of the machine.Prepared for (optional) elevated pods that allow profile & horizontal machining. -- Machining(1) 13.4 HP (10 kW) Vertically mounted electrospindle router with: HSK F63 Adaptor; inverter driven 1,000 - 24,000 RPM with max. torque from 12,000 RPM.(1) 11-Position ATC tool rack mounted at the end of the machine. -- Operator & Machine ControlPC Based User-Friendly, icon driven control housed on the main machine base + "WOODFLASH" Operating System. -- Complete with:(1) 250 cbm/Hr Vacuum pumps; handheld terminal with: Potentiometer & emergency stop; automatic measuring system of the tool length.Sound absorbing protective head enclosure with debris curtain around bottom edge. -- Actual model: FELDER FORMAT4 - PROFIT H08 16.31

FELDER RL-350 Dust CollectorFelder clean-air extractors filter the air so that the dust remaining is less than 0.1mg/m cu. These exceptional air quality values are achieved by the position of the impeller. In other extracting systems, the impeller works by creating pressure between the machine and filter; with the Felder systems, the impeller is located on the clean-air side creating negative pressure throughout the system so no dust can escape. Specifications: -- 15 HP blower with 13-3/4" in-let -- Max. airflow 4,705 CFM, nominal air flow capacity 4,072 CFM -- Static pressure 9.4" WG -- Compressed air connection for automatic cleaning function. -- Dust emission quality less than mg/m cu. -- Filter surface area 71 m/sq. -- Acoustic pressure 75 dB -- Chip volume 2 x 55 gal. -- Dimension / Weight: 104" L x 45" W x 89" H, 1,785 lbs.

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FESTO - DSS3: Push Feed MoulderSpecifications -- 4-Head; -- 3-1/4" x 2" max. cap.; 3/32" x 3/16" min. cap.; min. length 10". -- Equipped with: (2) Side heads; 7 HP - 9,500 RPM motor; top & bottom heads 3 HP - 8,500 RPM motor each; 3/4" dia. spindle. -- 4-Feed rollers steel & urethane. -- Top head tilts both directions.

FIN - ST 1600, ...Top/Bottom Cleaning Brush.62" Width and 3-1/8" max. thickness opening, thickness adjustment by handwheel via worm gear with dial indicator.Equipped with: -- Top & Bottom nylon brushes driven by 3 HP drive motor (only 1-brush with machine). -- Separate variable speed feed motor with magnetic controls driving 3" dia. rubberized infeed & outfeed pinch rolls. -- Full fabricated sheet metal enclosure for efficient dust collection, dust enclosure hood with central 6" dia. dust outlet connection.

FLETCHER/DELMAC - DMG-50CB, ...Contour EdgebanderSpecifications -- Overall table size: 18" x 48"; x 39-1/4"; H; 18" x 48"; Tilting section with: 0° - 15° Tilt.Equipped with: -- 20" Dia. Coil table. -- Guillotine. -- Glue Pot & Roller. -- DELMAC Thermo-Regulator Control with: (2) WATLOW "Series 965" Digital temperature controllers; LED display & touchpad for Glue pot & roller; LCD band length counter. -- Dual foot pedal controls.