BALESTRINI MINI C 2500 DOUBLE SIDED TEMPLATE PROFILE SHAPERSpecifications: -- (2) Offset shaping heads with 10 HP (7.5 kW), 230/460 volt three phase drives. (1 each side) -- Maximum reciprocating length 98" (2500 mm). -- Maximum height 7" (180 mm). -- Maximum width between spindles 8", and shaping heads are staggered for full end rounding. -- 1¼"; Diameter work arbors with 7″ under the nut capacity, and Spindle speed of 8400 RPM -- Hydraulic stroke of 9-3/4″ wide x 110″ long tee slotted work table, with feed speeds of 3 - 49 feet per minute (1-15 m/Min.) powered by 3 HP, 230/460 volt three phase hydraulic pump -- Overhead beam clamp bar with (4) adjustable clamps. -- Push button operator control station.

BALESTRINI 2 CAP Mortiser --Automatically mortises or bores round holes in chairs or case good --Specifications -- Twin tables with pneumatic holddown clamps, (1) on each side eliminating dead cycle time, 19" long tables tilt left or right 0ø to 20ø. --Equipped with & Features -- 3 HP - 9,000 RPM Spindle motor and 1 HP oscillation motor. -- Spindles are mounted on prismatic guides with adjustable bronze gibs and move by rack & pinion, -- (120) to (240) oscillations/Min; 4-23/32" max. oscillation length, -- 3-1/8" max. depth, 7/8" max. bit dia., 13 mm spindle collet dia.

BALESTRINI - 2 CAP: MortiserAutomatically mortises or bores round holes in chairs or case good.Specifications -- Twin tables with: Pneumatic holddown clamps, (1) on each side eliminating dead cycle time; 19" long tables tilt left or right 0° to 20°.Equipped with & Features: -- 3 HP - 9,000 RPM Spindle motor and 1 HP oscillation motor. -- Spindles are mounted on prismatic guides with: Adjustable bronze gibs and move by rack & pinion. -- (120 - 240) Oscillations/Min; 4-23/32" max. oscillation length. -- 3-1/8" Max. depth; 7/8" max. bit dia.; 13 mm spindle collet dia.

BARKER 600 HP BOILER, BIOMASS-FIRED: -- BARKER Boiler and Fuel System built & tested in 2011 as a pilot unit. Successful testing has been completed. This surplus equipment includes the following main features: -- Combustion Temp Capability- 2,000 deg. F.; Steam Flow 24,000 lbs/hr saturated; Steam Pressure 1,500 PSI @ 600 deg. F. -- Fuel Feed rate - 3,000 Lbs/hr at 1/4" biomass (5% moisture) -- Heat Input - 7,500 btu/Lbs HHV @ 22 mmbtu/hr. -- All equipment has less than 2,500 actual operating hours since installation.EQUIPMENT MAJOR COMPONENTS: Combustor, Cyclonic combustion technology, Refractory lined Heat Recovery. Steam Generator. Rotary Drum Dryer for Fuel drying - capable of 30% moisture reduction (at the above combustion parameters) and 1.5 tons per hour (installed as used equipment).BALANCE OF PLANT FUEL FEED SYSTEM: Live-bottom bin, Bunker, Feed conveyors, Wood hog, Vibrating screen, Drag and screw conveyors. Boiler water system - feed pump, water and steam piping Emissions Control: All required bag houses (SJVUAPCD) California permitted. -- Now REDUCED PRICE from $1.5 million !!

BECCA - 25000: 22 Liters / 6 Gallon Cap.; 2.05 kW Fully Automated Solvent Recycling SystemSpecifications -- Processes: Conventional, alternative, & waterborne solvents. -- Boiler cap.: 6 Gallons; thermic oil cap.: 3.2 Gallons. -- Heating chamber size (approx.): 14"; Dia. x 14"; dia. -- Solvent recovery rate: > 90%. -- Operating temperature: 140° - 392° F. -- Operating Pressure: -0.223 - 1 Bar Absolute; -0.776 to 0 bar relative. -- Adjustable cycle time: 3 - 5 Hrs. Equipped with: -- Dual skin AISI 304 Stainless Steel heating chamber with: AISI 304 Stainless steel pressure relief lid; replaceable solvent-resistant thermal gasket seal. -- AISI 304 Stainless steel boiler with: Indirect thermic oil bath & (2) heating elements. -- Fan cooled copper condenser system with: Aluminum non-sparking fan blade. -- Temperature/Cycle time digital touchpad control with: LED Display; self-diagnostic system; liquid & oil temperature primary electronic & backup mechanical sensors.Complete with: Installation, Start-Up & Operator's Guides.

BECKER VTLF 2.250 VACUUM PUMP (OIL-FREE VANE):Specifications -- (1) 7.5 kW (10 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System. -- Pump has: 169 CFM Total; 338 CFM max.; 25"Hg; Heavy-Duty construction; compact design; small footprint. -- 100% Oil-less Vacuum Pump is virtually maintenance-free with: Built-in carbon vanes & built-in suction filters; vacuum regulating valve; secondary suction for additional cooling; blow off valve/silencer. -- 2-1/2" BSP x 2" NPT Nipple coupled to a TFC; 1,150 RPM motor.

BECKER VTLF 2.250 VACUUM PUMP (OIL-FREE VANE):Specifications -- (1) 6.4 kW (9 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System. -- Pump has: 169 CFM Total; 338 CFM max.; 25"Hg; Heavy-Duty construction; compact design; small footprint. -- 100% Oil-less Vacuum Pump is virtually maintenance-free with: Built-in carbon vanes & built-in suction filters; vacuum regulating valve; secondary suction for additional cooling; blow off valve/silencer. -- 2-1/2" BSP x 2" NPT Nipple coupled to a TFC; 1,150 RPM motor.

BECKER KVT 2.100 3.6 Kw (5 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System, rated at 69 CFM and 100 cm/Hr with max. 27"Hg: Heavy Duty construction, compact design, small footprint. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blowoff valve/silencer. -- Complete with vacuum pump stand and double inlet vacuum air filter system.

Becker VTLF 250 Vacuum Pump: 9.3 kW (12 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System, 176 CFM, max. 25"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; 2-1/2" BSP x 2" NPT nipple coupled to a TEFC; 190-255/330/440V, 1,160 RPM motorNote (2) unit available and the price is for each

"BECKER" VTLF 2.250 Vacuum PumpSpecifications: -- (1) 6.4 kW (9 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System; -- Pump has 169 CFM total 338 CFM max. 25"Hg; Heavy Duty construction, compact design, small footprint. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blowoff valve/silencer; -- 2-1/2" BSP x 2" NPT nipple coupled to a TFC; 1,150 RPM motor.

BECKER KVT 3.100 3.6 Kw (5 HP) Vacuum pump:Oil-less (Dry) Rotary Vane Vacuum Pump System, rated at 69 CFM and 100 cm/Hr with max. 27"Hg; Heavy Duty construction, compact design, small foot print. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer. -- Complete WithInlet vacuum air filter system.

BECKER VTLF 2.250 VACUUM PUMP (OIL-FREE VANE): -- Specifications: QTY (2) 7.5 kW (10 HP) Oil-less (Dry) Rotary Vane Vacuum Pump System; -- Pump has 169 CFM total 338 CFM max. 25"Hg; Heavy Duty construction, compact design, small footprint. -- 100% Oil-less vacuum pump is virtually maintenance-free with built-in carbon vanes & built-in suction filters, vacuum regulating valve, secondary suction for additional cooling, blow off valve/silencer; -- 2-1/2" BSP x 2" NPT nipple coupled to a TFC; 1,150 RPM motor. -- Complete Becker Pump Stack, VTLF 2.250, 10HP x 2.

BELFAB RPJ26-121 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan.Specifications: -- 15,285 CFM approx. baghouse dust collector with (121) filter bags at 10-feet long with metal cages. Total of 1,884 sq. ft of cloth area. -- Filter Cleaning: Reverse Pulse Jet (RPJ) via plant compressed air that is sequenced by diaphragm valves/solenoids/manifold thru to a Venturi that injects a burst of air pressure to dislodge the dust build up on the outside of filter bags. This is a continuous process during the operation of the dust collector. (no shut down is needed). -- Main Fan: 75 HP side-mounted blower motor. with approx 26" dia. inlet. Rated at approx 15,000 CFM @ 15" SP. -- Comes with: Main starter with control panel. -- System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, safety railing, and approx. 20" Rotary Air Lock. -- Housing is about 8'-5" square by about 23' high overall. Weight with structure is about 8,600 Lbs. Note: Round cone section with storage capacity of about 246 cu ft may not be included. in above height and weight. -- Available in May 2025.

BELFAB - NBM5-20: Modular Dust CollectorPatented modular technology; 6,000 CFM with a static pressure of 10"; designed for current need that can easily be upgraded, as required. -- Exterior design; each "NBM" filter module with: (1) Service door & (1) explosion door per NFPA 68 safety regulations; unit has (5) filter modules. -- Each "NBM" filter module with: (18) 7" x 60" Poly twill filter tubes. -- Direct drive centrifugal Fan Assembly with: HUMMER 20 HP @ 1,800 RPM High Efficiency TEFC blower Motor; UL & CSA approved; AMCA Class-C anti-spark blower assembly with: Heavy Duty steel impeller; 16" inlet dia.; 825 sq. ft. filter surface area. -- Control Panel & Shaker Mechanism includes: (2) Interlock magnetic starters; (1) for the blower motor & (1) for the automatic shaker mechanism; adjustable timer; pilot lights all pre-wired. -- Includes: (10) Plastic drum.

BENCHMARK 205-HP3 Hot Melt Adhesive ApplicatorHot Melt Adhesive Applicator with: -- Bodine adjustable speed motor. -- Bead dispensing applicator. -- Also includes an extra Bodine adjustable speed motor regulator, for fine tuned glue application.

YM-800 1 YARD 4 OR 5 TINE Orange Peel GrappleSpecifications: -- Operating Weight 2,400lbs -- Opening Width 71 1/8" -- 4 or 5 Tine in stock - Ready to ship -- Rotating -- Hanger for Extra Cost

YM-1000 1.3 YARD 4 TINE Orange Peel GrappleSpecifications: -- Operating Weight 3,100lbs -- Opening Width 78 3/4" -- 4 Tine in stock - Ready to ship -- Rotating -- Hanger Included

BIESSE ROVER 20 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working field: "X" Axis 113.9" (2,893 mm); "Y" axis 37.4" (950 mm); "Z" axis stroke is 3.9" (100 mm), max. panel thickness 2-1/2" (65 mm). -- Positioning Speed:"X" Axis at 246 FPM (75 MPM); "Y" axis 147 FPM (45 MPM); "Z" axis 49 FPM (15 MPM)."X" Axis moves on high precision prismatic guides and ground helical rack; "Y" & "Z" axis via hardened ground ball screw. -- Worktable:(6) Pneumatically locked & manually positioned panel supports with (2) vacuum cups each.(2) Working zones with: (6) Pneumatic backstops; (2) pneumatic side & (2) center stops; stops raised & lowered automatically by start/stop of machining cycle. -- Boring Unit:(1) 2.3 HP - 5,135 RPM Motor; (10) vertical spindles independently operated with (6) in "X" axis & (4) in "Y" axis.(6) Horizontal spindles: (2 +2) in "X" Axis & (1 + 1) in "Y" axis; 2-1/2" (65 mm) max. boring depth.(1) "X" Axis grooving saw with: 120 mm Dia. blade - 5,200 RPM. -- Machining: Equipped with: (1) 9 HP (6.6 kW) Air-cooled "Quick Change" electro spindle with ISO 30 adaptor.Router is driven by: 10.2 HP (7.5 kW) Inverter for variable speed from 1,000 - 24,000 RPM; RH & LH rotation.(1) 3-Position automatic tool changer mounted at the back of the machine for "on the fly" ATC. -- Operator & Machine Control: Separate Control Console with: CNi "NC 410" Operating System housed in air-conditioned cabinet.8" LCD Monitor: Displays programming graphics, numerical & function keyboard; 512 KB RAM memory; (1) "UPGRADED" USB drive.RS-422 Serial port for PC and RS-425 port for inverter connection; EPROM for machine data & subroutines; machine runs production programs while programming and editing. -- Complete with:Stabilized autotransformer for voltages between 200 - 600 Volt 50/60 Hz; (1) 100 cbm/Hr Vacuum Pump; triple photocell barrier; assortment of misc. parts and tooling; Users operator/maintenance manuals & backup disks. -- Actual Model is: BIESSE - ROVER 20.

BIESSE ROVER K 1532 CNC MACHINING CENTER (W/ATC & "C" AXIS): -- Specifications:"BRIDGE GANTRY" machine with a working field in "X" axis 126" (3,200 mm), "Y" axis 61" (1,560 mm), max. material thickness 6" (165 mm). -- Positioning speed:"X" Axis 279 FPM (85 MPM), "Y" Axis 196 FPM (60 MPM), "Z" axis 65 FPM (20 MPM). -- Work Table:(8) "ATS" Panels supports with lifting rails for heavy pieces; (4) "ATS" vacuum pods with universal clamping systems on each panel support.BIESSE "Set Up Assist" & digital readouts for pod & rail placement.(2) Independent working areas with (8) pneumatic back stops, (2) pneumatic side stops & (2) pneumatic central stops. -- Boring Unit:4 HP (3 kW) motor with variable speed from 1,500 - 7,500 RPM;"BL 30" Boring head with (20) "Quick Change" independent vertical spindles, (9) spindles in "X" axis & (11) spindles in "Y" axis;(8) Horizontal boring spindles with (2+2) in "X" axis & (2+2) in "Y" axis;(1) "X" axis grooving saw with 120 mm dia. blade. -- Machining:(1) 17 HP (12.6 kW) electro-spindle router with HSK F63 adaptor, variable speed from 3,000 - 24,000 RPM.Motorized dust deflector shield & 6-position adjustable dust suction hood,(1) NC controlled "C" axis for 360° horizontal processing.(1) 16-position ATC tool plate mounted on board the "X" axis at the rear of the machine. -- Operator & Machine Control:PC Front End with Biesse "BH 660" + Biesse "bSolid" + Windows "7 WRT" operating system,15" Flat screen monitor, full standard keyboard & mouse, 1.44MB & CD ROM disk drives for data entry,RS 232 & USB ports, Ethernet connection, specific function controls & internet trouble shooting capabilities.Electronics are mounted in an air conditioning & dust free environment control cabinet. -- Biesse "bSolid" is a 2D/3D Cad/Cam software program that supports the performance of any machining operation thanks to vertical modules designed for specific manufacturing processes.Planning with "bSolid" takes just a few clicks & has endless possibilities; "Real-Time" simulation allows the operator to visualize the piece prior to processing, it provides virtual prototyping of the piece to avoid collisions & ensures optimal machine performance. -- Complete with:(1) 250 m³/Hr Vacuum pump; Hand-held "Remote Control" pendant for immediate operator control; LED bar with (5) colors that show the machine's status in "Real-Time".Safety fences, safety bumpers, safety photocells & safety mats; scrap conveyor; original documentation + user & maintenance manuals, wiring diagrams and operation of Numerical Control. -- Actual Model is BIESSE ROVER K 1532 G VS2

BIESSE - AKRON 855, ...Edgebander with Premill & Corner Rounding (Loaded!)Specifications: -- Edge & Workpiece Capacity: 0.4 - 15 mm (0.016" - 0.59") Edge thickness; 14 - 65 mm (0.55" - 2.56") edge height; 10 - 60 mm (0.39" - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3.3") min. panel width. Infeed Section: -- Premilling Unit - "FI-701"Rectifies face to be edged before applying glue; horizontal & vertical movement of (2) motors on linear guides; independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) - 12,000 RPM motors; independent copying pads on each unit, Autoset device to ensure optimum positioning of cutters according to thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit - "VC-710"With automatic edge magazine for strip & coil stock; 3 mm (0.04") PVC guillotine; "TEKNO-GLUE" System includes: Pre-Melt "QM-701"; for quick heating & tank changing with floating & bidirectional glue roller applicator & NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).WORKSTATIONS: -- End (Edge) Trimming Unit - "IN-701-V"(2) 0.35 kW (0.5 HP) - 12,000 RPM Motors; automatic 4-position programmable chamfer from Control Panel (0°, 3.6°, 11°, 15°); sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit - "RS-701"Top & bottom; (2) 0.8 kW (1 HP) - 12,000 RPM motors with superimposed motor position; 1° tilt capability; includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit - "RI-701"(2) 0.65 kW (0.87 HP) - 12,000 RPM Motors; for radius top & bottom fine trimming; unit can be tilted 0° - 45°; includes: NC axis multiple machining device. -- Corner Rounding Unit - "CR-200V"For corner rounding; top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") max. edge thickness. -- Edge Scraping Unit - "RB-701"For finishing rounded off edges in PVC or ABS up to 5 mm (0.20") thickness includes: Pneumatic Unit Lifter. -- Flat (Glue) Scraper - "RCC-700"Top & Bottom, Removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700":Top & Bottom. -- Hot Air Blower Unit - "PH-700" - (2) STEINEL "2346" 2,000 W; reactivates color of thick plastic.Complete with: -- PC-Based Control Panel with: 15" Color LCD monitor, HF (High Frequency motors on all cutting & trimming workstations. Top pressure beam programmable via positioning motor; top pressure provided by belt holddown. 36" Dia. Coil table: Padded sound enclosure. -- Manuals (as pictured).Dimensions: 280" x 42" x 72" H. - Weight: 3,500 kG (7,750 Lbs.).