SANDMAN DL9648 Downdraft Sanding TableThe DL9648 is a dedicated 96" x 48" sanding table that doubles as a workbench. The Sand Pro DL9648 is perfect for sanding large pieces such as doors or as a multi-person sanding station. Specifications: -- Table height 36", table size 96" x 48". -- (2) 1.5 HP TEFC motors with 7,400 CFM @ 1.5 SP and (2) 16" backward inclined fans. -- (6) Extended surface pleated filters each 20" x 25" x 2" deep w/ 1/2" netted polyester filter. Features: -- (4) 110 V duplex receptacles. -- Rubberized mar-proof top. -- Grid system top for jigs and fixtures. -- Hinged top with gas strut lid support for easy access to filters. -- (2) 10" x 32" Shelves. (2) 18" x 24" Storage drawers. -- Stainless steel hanger for air orbital sanders (choose 5" or 6"). Options: -- 3" Swivel casters (Adds 3/4" to machine height). -- Case of (12) replacement filters. -- Single phase available -- 18 Month Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL7236 Downdraft Sanding Table;The SANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench. -- 72" X 36" Rubberized work surface. -- 1.5 HP T.E.F.C. 220V 1-Phase motor with 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 4" wheels, (2) ridged, (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Adjustable in height from 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu. Ft. of built in storage area with 1 pull out shelf. -- 18 Months Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN M7236 Downdraft Sanding Table110V 1 HP (M7236) T.E.F.C Motor with 15’ power cord. -- 72" x 36" Rubberized work surface. -- 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 5" wheels, (2) ridged and (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Grid system top adds versatility. -- (18) Month warranty on parts.NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL7236 Downdraft Sanding TableSANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench.Specifications: -- 72" x 36" Rubberized work surface. -- 1.5 HP T.E.F.C. - 220 V - 1-Phase motor with: 10-5/8" LAU Blower with sealed ball bearings. -- Industrial casters with: 4" Wheels: (2) Ridged; (2) swivel-lock 2-ways. -- Magnetic tool holder. -- Hinged tilt up top with: Gas strut lid support for easy filter servicing. -- Adjustable in height from: 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu./ft. of built-in storage area with: 1 Pull out shelf. -- Easy filter service.

SANDVIK - QJ241: Jaw Crusher -- New in 2015. - Tier 3 Engine. -- Productivity: Highly productive; 1,000 x 650 mm; 40"; x 26"; jaw opening for maximum throughput. -- Hydraulic CSS jaw setting adjusted using control panel or handset; to avoid interruptions. -- Load sensing system for feeder drive & jaw level sensor ensures continuous crushing. -- Ideal for Recycling with: Reverse crush, overband magnet, and hydraulic raise & lower facility on main Conveyor for rebar clearance.

SANI-TECH -, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

STETON P150C Two Platen Cold Press. (Was made as a hot press but heating is not working!) -- Approx. 118" x 51" (3500 x 1300 mm) overall platen size, side loading on 118" side. Pressure from bottom. 2 HP hydraulic pump. -- Maximum daylight opening 450 mm. (17"), less thickness of middle platen. Total pressure: 150 tons. -- Number of cylinders; eight (8). Dia. of cylinders: 3.35" (85 mm) -- Platen material: aluminum. -- Parallel guidance by toothed rack: Yes -- Pressing time selectable: Yes -- Pressing force: Electro-Hydraulic -- Technical type: Upstroking press -- Boiler: Approx 30 KW but heating is not working --Weight: 6.500 KG (14,300 Lbs)

STRIEBIG - COMPACT: Vertical Panel Saw (15' Cut Cap.)Specifications -- 4 HP Motor with: Automatic STAR-DELTA starter electric brake (stops within 4 Sec). -- 181" Rip cap.; 64" crosscut; 2-3/8" (60 mm) cutting depth; 250 mm Dia. (9-7/8") blade with: 30 mm Bore - 5,400 RPM rotation. Equipped with: -- Full length center measuring rail with mid-level flip-out small parts support shelf; special long-wing crosscut measuring stop; crosscut lock-in stations in 40" increments. -- Automatic mechanically shifting support grid with: Replaceable lath tips for rip-cuts. -- Specially designed measuring flip stop for use with small parts; (6) template bar stops for setting common rip cuts; split center shelf useful for staging material; auto-engaging splitting wedge (riving knife)Complete with: -- Heavy-Duty panel support roller system (1,200 Lbs cap.) with: Integral panel stop brake. -- Dust extraction system to rear of frame (requires a bag or dust collector); 4" dust extraction connection. Includes: -- (3) Adjustable base & rear supports for free-standing installation of the one-piece fully welded frame. -- Dismantling and loading onto flatbed truck.Actual model: STRIEBIG Compact 5207.

STROUP 4' X 20' Cold PressSpecifications: -- 50" x 244" End Loading, Segmented, Bag press with motorized daylight opening. -- (2) Individually actuated, 50" x 122", segmented platens. -- Single air bag per platen with approx., 50 PSI specific pressure. -- Motorized adjustable daylight opening from 9" to 56". -- End loading with (2) rows of spring-loaded pop-up rollers in lower platen for easy loading/unloading of the press.

SULLAIR 10B-50 ACAC Rotary Screw Compressor (Open Type)Specifications: -- 50 HP - 1,770 RPM Motor, rotary screw air end, 100-110 max. PSI, approx. 180 ACFM; (2) asymmetrical lobe profile rotors only make contact on a lubricated pitchline to virtually eliminate cap. or efficiency loss. -- Equipped with: -- Tapered roller bearings on discharge and cylindrical bearings on inlet for high load carrying capacity. -- Pressurized fluid lubrication & cooling of Compressor with rigid piping & tubing; efficient 2-stage air/oil separation with replaceable element. -- Spin-on fiberglass fluid filter, Heavy Duty inlet air filter, cap. modulator stabilizes system pressure and matches output to demand (minimizes need for air receiver & reduces wear caused by start/stop). -- Includes: -- Electro-mechanical gauges & controls, air after-cooling.

SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023) Specifications: Cap. 111 ACFM. Rated pressure 60 - 125/135 PSIG. Noise level 85 dBA. Equipped with: E-Profile rotor design air end. 30 HP 3,530 RPM Motor. Air-cooled aftercooler. SULLAIR “SUPERVISOR II DELUXE” Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023)Specifications: -- Cap. 111 ACFM. -- Rated pressure 60 - 125/135 PSIG. -- Noise level 85 dBA.Equipped with: -- E-Profile rotor design air end. -- 30 HP 3,530 RPM Motor. -- Air-cooled aftercooler. -- SULLAIR “SUPERVISOR II DELUXE"; Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop.

SULLAIR LS-10, 30 HP SCREW AIR COMPRESSOR: -- Specifications:30 HP Motor, rotary screw air end, approx. 115 PSIG - 125 PSIG max; Mounted upon 150 Gal. receiver tank.Approx. Dimensions: 64" x 32" x 65"; Approx. Weight: 2,500 lbs. -- 2,630 Approx. total operating hours. Hour meter: Inoperable.