DOUCET MFE 300 Lateral chain feeder for moulders and optimizers -- 3'0" x 16'-0" working deck for material length 2'0" - 16'0"; width 2" to 9.5" and thickness 1/2" to 4". -- Feed system: Hydraulic variable speed 50-300 FPM with a 20 HP power unit. In-feed (4) roller accelerator; (2) top steel rollers and (2) bottom drive roller. Additional idler rollers along feed fence to support lumber during feeding. -- Chains: Transport length of lateral chain feeder 3'0". (8) strands of C2060 chains on pneumatic up/down device to release lateral pressure on board when feeding. -- Pedestal: Feeder controls mounted to pedestal with extended cable. Interface relay to stop feeder when moulder is stopped. -- Adjustments: Tool less adjustment handles for quick setups. Easy access to for thickness adjustments at front side of feeder. -- AVAILABLE OPTIONSOne (1) set of four (4) feeding wheels made of steel with hardenedsurface teeth $ 1 000.One (1) set of four (4) feeding flat wheels made of steel, 2" wide insteadof 1" for wide material feeding $ 500.One (1) set of four (4) feeding flat wheels made of steel 1" wide $ N/C.Guiding Tunnel between feeder and moulder,Standard Guiding Tunnel (4' long) $ 1 650.Standard Short Guiding Tunnel (32" long) $ 2 100.Complete Guiding Tunnel (4' long) $ 2 700.Complete Guiding Tunnel with adjustable fence (4' long) $ 3 800.Motorized Guiding Tunnel (4' long) on request.Additional chain transfer length capacity (up to a maximum of 6additional feet) For MFE-300-16 sold per foot $ 1 685. Note: More than 6 add. feet: price upon requestSteel plates between chainsFor MFE-300-16 $ 1 050.Platen chains recommended for softwood speciesFor MFE-300-16 $ 2 850.One (1) additional chain for shorter material down to $ 1 750.18" min. lengthPressurized lateral guide with roller bearing end $ 1 400.Powered lateral guide with roller and side guides on request.Custom working height on request.

DUBOIS Vertical Edge Fill System with Micro UV This machine is designed to fill voids and defects in edges for a smooth, quality finish. These coaters are ideal for filling porous open grain panels like oak, veneers, particleboard, and MDF. Compatible with solvent based, water based, and UV fill coating.1.1 One (1) Continuous chain transport system- Top and Bottom chain transport conveyor with speed matching attachment conveyor chain- Aluminum backed chain pads with EPDM covering1.2 Two (2) double sided vertical edge denibber/buffer- Operator side Adjustable up to 12"; wide, back side fixed edge- Post mounted vertical denibber head- 12"; dia. x silicon impregnated scuffing wheel, buffer wheel to be determined- Dust hood with 4"; connection- Vertical head oscillation for even brush wear- Inverter controlled drive provides speed control for brush and oscillation1.3 Two (2) double sided vertical edge fill stations- Operator side Adjustable up to 12"; wide, back side fixed edge- Electric motor driven Applicator and Doctor roll drives- Quick change applicator sleeve design, 1-1/2"; face- Stainless steel distribution pipe with spring tension- 9"; dia. chrome plated reverse roll- Stainless steel catch pan and drain lines- 3/8"; pail mounted pump and agitator- Spring loaded doctor bar, urethane dr. blade- Air cylinder dr. roll engagement with stroke adjuster- Inverter controlled drives provides speed control for applicator and doctorrolls1.4 Edge Cure UV Oven Banks- Each bank to consist of Two (2) double sided Fusion F600 Microwave UVovens- Space for two (2) future double sided Microwave UV Units- Individually adjustable three (3) position lamp power selector switch(300, 400 & 600 w/in.)- Irradiator cooling exhaust fan for each set of four (4)2. Control Panel System- NEMA 12 Hinged Door Enclosure, with disconnect, required fuses, door mounted buttons and cooling fans- Allen Bradley HMI, PLC items included- Top mounted panel cooling fan- Required Inverters· Edge Fill Finishing Machineo Top and Bottom Conveyor driveso Denibber/Buffer Brusheso Denibber/Buffer oscillatorso Applicator Rollso Doctor Rollso Reverse Rollso UV oven Exhaust fansDesign Parameters- Machine is located in Explosion Proof Area- Voltage= 480 V., 3 Ph., 60 Hz.- Design Speed = 70 - 200 FPM- Line height = 36";- Max./Min. Part Width: 12"; / 2";- Max./Min Part Length: 245"; / 24";- Max./Min Part Thickness: 1-1/4"; / 3/8";- Paint Color· Main Frame and Conveyor: Blue / TS White· Guards: safety yellowNotes:- ¼"; product has the potential of being processed in this machine but has less probably of being successful the wider the product.

The Dubois SP-12 Linear Spray Machine is an automated linear finishing machine that can be used for a variety of applications including priming, staining, sealing, lacquering, etc. of linear stock. This spayer comes with (3) three arms, (3) three guns and (1) one paint pump. The guns are Binks spray guns Model 363, and Binks pump.Compatible with both waterborne and solvent based coatings --Three adjustable gun arms --9’-0"; long variable speed live roll conveyor w/ electric powered drive --Pneumatic gun trigger mechanism to automatically trigger guns on/off --Infeed guide fences --Top roller hold-down on infeed table --Ability to enable/disable individual guns --Easily cleaned spray trough --Adjustable atomizing air pressure --Adjustable fluid pressureIncluded optional features: &#9679 Stain wipe station mounted to outfeed with stain wipe brush &#9679 Exhaust system with spray enclosure, exhaust fan, & exhaust filter system &#9679 Denibbing station mounted to infeed

DURAMAC - DUR52-2, ...2-Head Wide Belt Sander2-Head Wide Belt Sander with: Drum, combi-head, and brush cleaner. -- Max. working width: 52". -- Max. working thickness: 6". -- 23" Infeed load space. -- 50" Wide rubber conveyor belt size. -- 1st Head: Grooved rubber contact sanding drum; 40 HP, 230 Volt - 3-phase drive motor. -- 2nd Head: Combination contact drum & polishing platen; 30 HP, 230 Volt - 3-phase drive motor. -- Spring-loaded pinch rollers. -- Electronic belt tracking, pneumatic belt tensioning. -- (1) Rear top outfeed panel brush cleaning head, 0.5 HP, 230 Volt - 3-phase drive motor. -- Power raise & lower of worktable. -- Inverter driven feed works drive motor for variable speeds, 0 to 60 FPM. -- Front operator control station; motor ammeters. -- TOSHIBA Feedworks inverter. -- "DP-626S" electronic digital readout for setting table heightAlso Available: -- Transformer for 600 Volt operation, 112.5 KVA.

DUST TECHNOLOGY DT-250 Modular Dust Collector Free-standing self-contained internal air system, 25 HP Motor;Specifications: -- Rated for 9,800 CFM, 5-bag unit, 75 cu. ft. collection capacity. -- (5) Upper cloth filter bags with 165 sq. ft. filter area; 16" inlet dia., dust baffling system to fill bags evenly. Supplied with & Includes: -- 25 HP motor with magnetic starter, -- (5) Upper cloth filter bags and (5) lower plastic collection bags. -- (5) Double "T: Bolt straps. -- (5) Quick release metal straps. Three Year Comprehensive Warranty

DUST TECHNOLOGY DT-200 Modular Dust Collector Free-standing self-contained internal air system.Specifications: -- 20 HP Motor, rated for 7,500 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 132 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. Features & Includes; -- 20 HP motor, magnetic starter; -- (4) Upper cloth filter bags and (4) lower plastic collection bags. -- (4) Double "T: Bolt straps. -- (4) Quick release metal straps. -- Magnetic starterThree Year Comprehensive Warranty

DUST TECHNOLOGY DT-50 Modular Dust Collector5 HP BALDOR Motor, compact 2-bag free-standing & self-contained Heavy Duty Dust Collector, rated @ 2,400 CFM, 9" - 11" static pressure at fan. -- Equipped with: 10" Inlet dia., (2) Cotton Filter bags with 66 sq. ft. filter area and (2) Plastic Collection Bags w/ 30 cu. ft. collection capacity. -- (2) Double "T" Bolt Straps and (2) Quick Release Metal Straps. Includes: Magnetic Starter

DUST TECHNOLOGY DT-150 Modular Dust Collector Free-standing self-contained internal air system, 15 HP Motor, rated for 6,000 CFM, 4-bag unit, 60 cu. ft. collection capacity. -- (4) Upper cloth filter bags with 133 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. -- Includes: 15 HP motor, magnetic starter, (4) Upper cloth filter bags with 133 sq. ft. filter area and (4) lower plastic disposable collection bags

DUST TECHNOLOGY DT-75 Dust Collector7.5 HP BALDOR Motor, compact 3-bag free standing & self-contained heavy-duty dust collector, rated @ 3,450 CFM, 9" - 11" static pressure at fan. -- Equipped with: 12" Inlet dia., (3) upper filter bags with 99 sq. ft. filter area (patented BEANE bags designed to be 99% efficient to .5 microns). -- Dynamically balanced sand cast poured aluminum high quality impeller with easy access; 45 Cu. ft. collection cap., dust is collected in 6-mil thick clear plastic or canvas collection bags for easy disposal or reuse, a unique adjustable baffling system assures even filling of bags. -- Includes: Manual motor starter with thermal overloads & push button station.

DUST TECHNOLOGY DT-100 Dust Collector3-Bag free-standing & self-contained heavy-duty dust collectorSpecifications: -- 10 HP BALDOR Motor, compact 3-bag free standing & self-contained heavy-duty dust collector, rated @ 4,450 CFM, 9" - 11" static pressure at fan. Equipped with: -- 12" Inlet dia., (3) cotton needle felt upper filter bags with 99 sq. ft. filter area or patented BEANE bags designed to be 99% efficient to 0.5 microns. -- Dynamically balanced sand-cast poured high-quality aluminum impeller with easy access; 45 Cu. ft. collection capacity. -- Dust is collected in 6-mil thick clear plastic or canvas collection bags for easy disposal or reuse, a unique adjustable baffling system assures even filling of bags. -- Includes Push-button Magnetic starter control.Dimensions: 24" Deep x 136" High x 107-1/2" Length; Weighs (810) Lbs.

DUSTEX W-2500 Whispurr 5-Bag Dust Collector. -- 8,500 CFM; 25 HP ultra quiet, self-contained high efficiency internal return (5) bag dust collector; 16" Dia. inlet, dynamically balanced impeller. -- Unit includes: (5) 60" filter bags, straps, gaskets, magnetic bag holders. -- Includes: Collection hopper w/ rotary air lock,

DUST-EX AG22 Abort Gate/Valve.... Automated two-way air stream diverter valve which prevents fires and explosions in dust collection systems and reduces the risk of fire in explosive prone work environments. A "safety measure essential" when clean air is returned to a building. -- Consists of: A lever arm that automatically directs a flapper damper in two different directions. -- Normal Position: The damper stays in a horizontal position (open) allowing the air stream to be directed/returned to the building -- Abort Mode: In the event of a spark originating upstream of an outside dust collector, a Spark Detection Sensor positioned in the air stream inside the building, sends a signal to de-energize an electro-magnetically controlled latch.The flap of the valve is very quickly switched to the abort/second position (closed) thereby diverting the explosion pressure/air stream to the atmosphere. Thus the inside work environment is protected from the explosion. -- Reset Mode: A pneumatically operated system is added to reset the damper position. -- Comes With: NEMA enclosure, 10" x 10" x 6". Enclosure for Pneumatics 22" x 22" -- All (3) flanged connections are 22" x 22'" square. -- Construction: Damper assembly is fully bolted to provide solid, reliable operation. -- The power adapter for the independent power supply is extra.Overall dimensions: 60" long x 36" wide x 43" high.Improve the safety of your work environment & help comply with NFPA codes!

DUST-EX HSAG-24 Packaged Safety Solution for a 22"x22" (24" dia. round equivalent) Return Air Rated for 10,000 CFM. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap Valve (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel. One-Zone CP05 Control Panel 1 inlet, 1 outlet: UL698A Control Panel for use with NFPA 69 compliant Explosion Isolation Valves. Standard panel includes status lights, intrinsically safe circuit (1 Per Zone), monitored inputs (3 total), ability to add a secondary clean air isolation valve, output for system shut down and monitoring, drawings, installation instructions, NEMA 4 outdoor rated enclosure, UL and Canada UL listings. Allows for 120VAC or 24VDC input power. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 39" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) High Speed Abort Gate, EM-HSAG02-24, magnetic (24 VDC), 22" x 22" flanged inlet and outlet (24" round equivalent), control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 10,000 CFM / 3000 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe

DUST-EX HSAG-24 Packaged Safety Solution for a 23"x23" (24" dia. round equivalent. Suitable for up to 25" dia. ) Return Air Rated for max 12,850 CFM @ 3,500 FPM.. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Heavy Duty Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel, Intrinsically Safe, CP05 - single zone, allows for installation of (1) inlet and (1) outlet explosion isolation valve(s), (3) monitored inputs per zone (two programmable), (1) intrinsic circuit with barrier and physical separation (one per zone), outputs for system shut down and monitoring, NEMA 4 enclosure, 120 VAC or 24 VDC. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 40" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK-02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) Heavy Duty High Speed Abort Gate, RGAG-23, magnetic , 23" x 23" flanged inlet and outlet (24" round equivalent), suitable for 21" - 25" dia., control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 12,850 CFM @ 3,500 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe (broken bag detector) RS-PDP03, RS-MK02DP, etc. IP 65 encl

EARTH CARE PRODUCTS, INC. 10½ Ft. x 32 Ft. Triple-pass Rotary Drum Dryer System with Gas Burner;Complete with the following major components: -- 10.5 Ft. x 32 Ft. (despite the model DB-1030) Triple-pass Insulated drum. -- Trunnion Bases, and 30 HP Drum Drive. -- High efficiency Cyclone, Cyclone outlet Airlock. -- 100 HP Dryer Main Fan, and Ducting. -- 25 MM BTU Gas Burner complete with Refractory Lined Furnace and Gas Train. Notes: &#9679 The Trunnion Tracks and Trunnion Wheels are in good condition as is the drum interior. The system was renovated in 2015 and not used much after the work was done. &#9679 The equipment is still in-place.

EMC MERCURY 1350 3WRK Abrasive Planer / Wide Belt Sander with (3) Heads; Planer Head, Contact Roller, and Combination Head.Useful working width 1,350 mm (53"). Working thickness min./max. 3 - 170 mm (1/8" - 6-11/16"). The machines uses abrasive belts 2,620 x 1,370 mm (103" x 54") for longer life of the sanding belts.Head configuration:1st Head: Planer Head "W" -- Cutter head knives diameter 140 mm (5-1/2"). -- Shaft for helicoidal position knives with (380) Interchangeable knives with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 20 independent segments. -- Anti kickback protection made of 72 independent elements. -- On-Off pneumatic cylinder for planer. group in working position. -- Working pressure adjustment. -- Motor power: 15 kW (20 HP). -- Automatic Star-delta starter. -- Speed rotation: 32 m/Sec (115 FPS). -- Soft starter for slow starting2nd Head: Steel Roller "R", Belts dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 180 mm (7"), spirally grooved. -- Electronic motorized roller pressure adjustment "Grit-set system". -- On-Off selector switch control for roller. -- Constant control to any position with accuracy 0.02 mm. -- Rotation: Against feed (clockwise). -- Motor power: 11 kW (15 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 18 m/Sec (59 FPS). -- Timing oscillating cleaning abrasive belt blower located at the bottom 3rd Head: COMBINATION Unit "K", Belt dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 140 mm (5-1/2"). -- Roller rubber hardness 45 Shore, Constant control to any position with accuracy 0.02 mm. -- On-Off selector switch control for 3rd roller including pneumatic piston -- Pneumatic Aluminum PAD , lamina 40 mm, On-Off. -- Quick changing system, extractable blade with felt, rubber and graphite. -- Rotation: Against feed (clockwise). -- Motor power: 11 kW (15 HP) with automatic star-delta starter. Abrasive Belt cutting speed:18 m/Sec (59 FPS).Feed system: -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 18 m/Min (9.8 - 58 FPM) Inverter Controlled. -- Automatic feed belt centering device. General Machine Features: -- Large diameter screws on machined guides with columns and pistons. -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each (head) working group. Electronic programmable color TOUCH SCREEN display, 7" wide -- PLC with micro-processor of latest generation, modular and expandable. -- Connection USB, RS232, Ethernet 10/100/1000. -- Memory capacity: 100 working programs or more. -- Graphic synoptic to facilitate programming.Software facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, programming and display for thickn

EMC VENUS 1300 1K ... Finishing Sander with (1) Sanding Head: Combination Head.Useful working width 1,300 mm (51"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").Working Unit: Combination Roller & Pad. -- Roller diameter 142 mm (5-5/8"). Rubber covered hardness 85 Shore. Roller pressure adjustment control & "Grit-set system". Main Motor On Off Selector control with pneumatic piston to select roller, 22 kW (30 HP) Automatic star-delta starter Rotating cutting speed: 18 m/Sec (59 FPS). -- PNEUMATIC Controlled Flexible Sanding Pad Including On-Off Selector: Quick Change System: Removable pad with felt, rubber and graphite. Rotating cutting speed 18 m/Sec (55.8 FPS). Abrasive belts oscillation by means of electronic photocell sensor.Feed system:CONSTANT PASS LINE - fixed infeed height 900 mm (35") from floorIdle table rollers support in infeed and outfeedRubber covered presser rollers, groovedVariable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM). Inverter ControlledLarge diameter screws on machined guides with columns and pistonsAutomatic feed belt centering deviceElectronic digital display for working thicknessGeneral Machine Features: -- Analog ammeters on main control cabinet. -- Electronic motorized grit set system, control from touch screen.Electronical Panel: -- Check Control Self Diagnostics with Alarm Control. -- Analog Ammeter on the main control cabinet. -- Infeed table thickness system electrically controlled. -- Independent Overload protection.Safety: -- Infeed front emergency swinging bar for oversized panels. -- Infeed protection pressing blade to avoid pieces to go back to operator. -- Rear and front emergency push buttons. -- Automatic brake on abrasive belts motors. -- Automatic emergency stop and alarm display in case of: &#9679 Low Air Pressure. &#9679 Doors opened ("easy maintenance and inspection"). &#9679 Electric motors overloading. &#9679 Emergency detector for over thickness material cut. &#9679 No tension on abrasive belt. &#9679 Abrasive belt lateral mistracking. &#9679 Abrasive belt broken.Idle table rollers support in infeed and outfeedCentralized Control Cabinet: &#9679 IP 54 protection against dust & moisture. &#9679 Analog ammeter on main control cabinet. &#9679 Table lifting-lowering thickness system electrically controlled. &#9679 AUTOMATIC Delta - Star starter on abrasive belts motors. Centralized independent pneumatic control cabinet: &#9679 IP 54 protection against dust & moisture. &#9679 Pneumatic air filter with automatic water-drain system. &#9679 Pneumatic adjustment for "Grit set system". &#9679 Pneumatic plant working without lubrication. &#9679 Compressed air pressure 6 bar (85 PSI). Options Available: Tampico Brush natural fiber brush for cleaning of the pieces, diameter 150 mm (6"). Motor Power 1.1 kW (1.5 HP). $3,950

EMC R-evo Z 1350 Sanding & Polishing Center for multi-directional Superfinishing - Award-winning system!Superfinishing obtained by combining electronically controlled, segmented sanding pads with the continuous rotation of the entire sanding head assembly (carousel). This revolutionary system is equally effective as regular wide belt sanders with 4 heads!The carousel rotation is servo-controlled, and can also be operated at standstill in any angular position. The revolving sanding head provides a much more consistent overall finish, and better use of the entire abrasive sanding belt.Motorized doors, sliding and foldaway. Useful working width 1,350 mm (53"). Working thickness min./max. 5 - 180 mm (0.2" - 7"); Constant pass line.Part/Panel Reading unit with Electronic Segments: -- RB-75 Panel reading at infeed, (75) segments with electronic feeler pads. -- Electronic commands activated by magnetic switches. -- Panel detection by large diameter rubber wheels. -- Integrated electronic system.Machine Specifications: -- Hyper finishing abrasive belt 4,960 x 1,430 mm (195.3" x 56-5/16"). -- Chevron belt (inside) length 4,560 mm (179.5"). -- Carousel rotating speed infinitely variable 0.1 - 40 RPM. -- Two electronically controlled segmented sanding pads. Both with 75 segments, each 18 mm wide. -- APC - Automatic Programmable Control and setting of the air pressure for the electronic pads. -- Sanding pads pressure controllable from 0 - 4 bar (0 - 58 PSI). -- Main motor 11 kW (15 HP), Inverter Controlled for infinitely variable abrasive belt speeds 3 - 18 m/Sec (10 - 59 FPS). -- Double oscillating blowers for parts & feed belt cleaning. Activated by part size. -- Motorized linear sliding doors, total stroke 2,100 mm (82.7"). -- Including abrasive belt loading trolley for easy exchange of the sanding belt. -- At outfeed: TAMPICO brush roller for part cleaning, diameter 150 mm (6"), and TAMPICO brush roller for feed belt cleaning, diameter 150 mm (6").Feed System: -- Constant pass line, 900 mm (35-7/16") from floor. -- P.A. Automatic thickness caliper with radio frequency remote control. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Vacuum conveyor bed assembly, fan mounted inside the machine. Inverter controlled 4 kW (5,5 HP) motor. -- Variable feed belt speed, adjustable from 2,5 to 16 m/Min (8 - 52 FPM), Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.Machine Management System: -- Electronic programmable color TSD TOUCH SCREEN DISPLAY, 15,4" wide. -- PLC Power Logic Control for high speed data transmitting. CPU Pentium Intel Atom Z510; 1,1 GHz, DDR2 RAM 512MB expandable. -- Connection 3x USB, 1x RS232, 1x Ethernet 10/100/1000. -- Memory capacity of (200) working programs. -- Operating system Microsoft Windows 7. -- Graphic synoptic to facilitate programming. -- Software and connections prepa

EMC ROTOPLUS 1350 – LUC (1)5 + BRILL 15 Polishing & Buffing LineHeavy Duty Automatic Polishing & Buffing line for high gloss lacquered panels, consisting of: -- Infeed Conveyor -- ROTOPLUS 1350 LUC 5+1 - Polishing and Wax Application machine -- Intermediate Conveyor -- ROTOPLUS 1350 BRILL 15x - Buffing Polishing machine -- Outfeed Conveyor -- Synchronization of feed speed of all equipment in the line, the Rotoplus machines including all conveyorsFollowing are the full specifications: -- Infeed Conveyor, 1.500 x 1.350 mm (59" x 53") Constant pass line 900 mm (35") +/- 40 mm (1-9/16"). Variable feed speed inverter controlled and electronically controlled for synchronized speed and transfer with all other machines of the line.Feed speeds from 0,4 to 8 m/Min (1,3 - 26 FPM). -- ROTOPLUS 1350 LUC 5+1Polishing and Wax application machine for high gloss lacquered wood panels for Polyurethane lacquer or brilliant straight, brushes adjustable at different angles. Equipped with (1) longitudinal Brush Head plus (5) rotating brushes on carousel.1st STATION - Longitudinal Polishing Brush:Cleaning polishing cotton brush diameter 275 mm (10-13/16").Length of the brush 1,420 mm (55-5/16").Brush inclined 3° in respect to the parallel 180°.Automatic low pressure Spraying Gun.Longitudinal chain rail system for gun movement.Electric adjustment of the working pressure, operated from main touch screen control unit.Main motor power 7,5 kW (10 HP).Rotating speed adjustable from 260 to 960 RPM by means of inverter 7,5 kW (10 HP). 2nd STATION - Polishing Carousel: CAROUSEL with (5) Brushes.Max. Brush diameter: 350 mm (13-3/4").Spindle diameter 80 mm (3-1/8").Spindle length: 400 mm (15-3/4").(5) Independent motors, 5,5 kW (7,5 HP) each, with counter bearing supports.The working angle of the brushes is adjustable.Variable speed adjustable from 3 to 36 RPM by means of electronic inverter, driven by 4 kW (5,5 HP) motor.Clockwise and anti-clockwise direction of rotation.Programmable speed control operated from main electronic touch screen display. (5) Special shafts for brushes support EXTRA in addition to the standard ones.(5) Cotton rags 350 mm (13-3/4") to fit the shafts.Automatic System for Abrasive Wax application:Pressurized tank (50) liters for liquid abrasives, with automatic miscellaneous bottom exit and pressure regulator for gun.Low pressure spraying gun for liquid abrasives.Electronic valve for spray gun control.Infrared high precision photocell to detect the panels and activate the spraying gun.Adjustable support for spraying gun positioning.Software and graphic control, programmable through PLC and touch screen. Software and Plug for Telemetry. Computer remote diagnostics control: Direct computer connection between EMC and customer, for online support. -- Intermediate Conveyor, 1.500 x 1.350 mm (59" x 53"), Constant pass line 900 mm (35") +/- 40 mm (1-9/16"). Variable feed speed inve

EMC FLEXY 1350 2RP Finishing Sander with (2) Sanding Heads, Roller and Segmented Finishing PadUseful working width 1,350 mm (53"). Working thickness min./max. 3 - 180 mm (1/8" - 7-1/16"). Head configuration:1st Head: Roller "R" Belt dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 250 mm (10"). -- Roller rubber hardness 85 Shore. Constant control to any position with accuracy 0.02 mm. -- Electronic motorized roller pressure adjustment "grit-set system". -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (15 HP). Automatic star-delta starter. -- Abrasive belt cutting speed: 18 m/Sec (59 FPS). Oscillating abrasive belt blower for the roller unit.2nd Head: Segmented Finishing Pad "P" Electronic PAD segmented in (50) sections. -- Belt dimensions: 2.620 x 1.370 mm (103" x 54"). -- Width of the segmented element (section): 27.0 mm (1-1/16"). -- Rotation: Against feed (clockwise). -- Timed oscillating abrasive belt blower. -- Motor power: 11 kW (15 HP) with electronic inverter variable abrasive belt speed 3 to 18 m/Sec (9.8 - 59 FPS).Feed system:Constant pass line, 900 mm (35.4") from floor &#9679 Vacuum conveyor bed, 4 kW Vacuum unit for holddown of smaller parts, mounted inside of the machine base. &#9679 Idle table rollers support in infeed and outfeed. &#9679 Rubber covered presser rollers, grooved. &#9679 Variable feed belt speed, adjustable from 3 to 18 m/Min (9.8 - 59 FPM) Inverter Controlled. &#9679 Large diameter screws on machined guides with columns and pistons. &#9679 Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized "grit set" system; control from touch screen for each working group (head).Electronic programmable color TOUCH SCREEN display, 10" wide &#9679 PLC with micro-processor of latest generation, modular and expandable &#9679 Connection USB, RS232, Ethernet 10/100/1000 &#9679 Memory capacity: 100 working programs or more &#9679 Graphic synoptic to facilitate programmingSoftware facilities: -- Automatic motor sequence starting. -- Display report and reset of alarms (self diagnostic) with memory records. -- Command, programming and display for:&#9679 all electronic pad functions&#9679 thickness&#9679 feeding&#9679 all inverters and for selected groups (heads).&#9679 blowers, including compressed air saving function.Centralized Control Cabinet: IP 54 protection against dust & moisture. Analog ammeter on main control cabinet. Table lifting-lowering thickness system electrically controlled. AUTOMATIC Delta - Star starter on abrasive belt motors. Centralized Independent Pneumatic Control Cabinet: IP 54 protection. Pneumatic air filter with automatic water-drain system. Pneumatic adjustment for "Grit set system". Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI) Options Available: Tampico Brush natural fiber brush for cleaning of