CK POWER CKT375VM-T4 DIESEL GeneratorSpecifications: -- Engine: Volvo Penta TAD1372 Tier 4 Final EPA/ CARB Certified -- Ratings Range: 60HZ (3 phase / .8 power factor) -- Prime: 275 kW / 343 kVA Standby: 300 kW / 375 kVA -- Standard configuration: multi-voltage selector switch, 120/240V 1 Phase, 120/208V 3 Phase and 277/480V 3 Phase -- Fuel tank: 300 gallon, 17 Hour run time @ 100% load -- Hours: less than 500Equipped with: -- CK/Deep Sea custom controls -- Easy to use custom configuration -- All components are UL1446 certified -- Fork pockets and transportation tie downs -- Lockable storage -- Level 1 sound attenuation: 70 dBA @ 23 ft. -- Standard 20 amp 120 volt convenience receptacle

CML NEW FINISHING TOWER/6 Multi Level Oven System: This type of oven is very flexible thanks to the FIFO (First In / First Out) operation and the possibility to adjust the stay time using more or less belt trays.It is particularly suitable to help the evaporation of the volatile components contained in UV curable paints, or to carry out a first degree of drying of conventional paints in an 'out of dust' environment. - Its technical characteristics also make this system extremely suitable for drying or curing materialDescription of the Standard Equipment & Specifications: -- Overall dimensions: 7,650 x 3,300 mm x 3,250 mm height (25’ x 11’ x 10.67’ H). -- Weight: 4.000 kG (8,819 Lbs)Multiple Floors Dryer, mod. TOWER/6 Paint Coated parts (panels components) are transported on (6) belt conveyor trays, moving vertically up/down, having a length of 6,500 mm (256") each. This practical length makes it possible to load "two panels charges" having a length of 3,000 mm. (9.85 feet) each. -- Max. weight supported by every belt tray level: 115 kG (253.5 Lbs). -- Max. allowed thickness 50 mm (1.97 inches) -- Speed controlled by inverter at belt travel steps of 3.250 mm (127.9") or in continuous model. -- Vertical movement on (4) pre-tensioned chains controlled by motor with gearbox. -- Cabinet made of structural carbon steel profiles and pre-painted insulated panels, complete with entry door and windows. -- Ventilation by means of laminar air distribution among the floors. Average air speed 2 m/Sec (6.56 feet/Sec) - (100% of the air volume is taken from the outside and exhausted to the outside). -- Air supply unit complete with centrifugal fan taking the air from the outside of the building, complete with heat exchanger to be supplied with hot water, with temperature adjustment system and double set of pocket filters. -- Air ductworks between air supply and exhaust fans and distribution boxes (plenum) is included. -- Ready to be connected to emergency system to stop the line -- Curing Tunnel operating functions controlled by SCHNEIDER PLC via electronic keypad input. -- Separate electrical cabinet in IP 55 execution - IP 55 motors -- Manufactured according to CE Standards and covered by a (12) Months or 2,000 Operating Hours Warranty for defective parts or materialOther Dims, Operation & Utilities: -- Dimensions of the electrical switchboard: 800 x 600 x 2,000 mm (2.7’ x 1,97’ x 6,56’) -- Total power: kW 10,5 -- Compressed air:: lt/Min 20 (5.29 gal/Min) -- Exhausted air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Supply air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Thermal power: Kcal/h 125.000 (326,000 BTU/Hr), - AIR In/Out: 50°C (122°F)

CNC FACTORY PYTHON XPR FLAT TABLE MACHINE (W/ATC): -- Specifications:4' x 8' Flat Table "Bridge Gantry" machine with: "Phenolic "MATRIX" grooved flat table for "NESTED BASE MANUFACTURING". -- Working capacity:"X" Axis 97" (2,464 mm); "Y" axis 49" (1,245 mm); "Z" axis stroke is 20.2" (515 mm); max. material thickness 10" (250 mm). -- Positioning Speed:"X" & "Y" Axis 279 FPM (85 MPM); "Z" axis 115 FPM (35 MPM).All axes movement is with 5G driverless Servo System with direct helical rack & pinion & 5G no homing calibration. -- Work Area:Flat table design with: "Matrix" grid phenolic surface for "Nested Base Manufacturing".The machine has: (6) Independent working zones with dual layer high flow vacuum; 2-left origins, 2-right origins, 1-front origin & 1-rear origin.Auto-material alignment pins, auto-unloading arm, material loading wheels; rear & side material alignment pushers. Automatic on/off vacuum flow, vacuum hold-down communication, automatic parts hold down, and release.Robotic Material Sensing Dust Hood; Single and dual vacuum ports. -- Machining:(1) 12 HP (8.9 kW) Air-cooled "HSD Electro-Spindle" with: ISO 30 adaptor, RH & LH rotation; variable speed from 1,000 - 24,000 RPM.(1) Rapid Fire 12-position revolving tool changer for "on the fly "ATC". -- Operator & Machine Control:"SYNTEC" PC Front End with: CNC Factory 5G, 5th generation CNC control + At machine cabinet and cutting software. Handheld MPG remote control with individual axis & real time simulation control; CNC speed control overrides & compensation at machine virtual support, HD digital monitoring camera, Wi-Fi, and Ethernet ready.Air-Conditioned control cabinet, 21" "TOUCH SCREEN" monitor; All mounted on a mobile cart. -- Complete with:(1) 150 cbm (60 Hz) Vacuum Pump; automatic pressurized Lubrication System for linear guides, pads and recirculating ball screw. Auto tool length measurement probe. Perimeter Safety System & fencing. -- Actual Model is: CNC FACTORY PYTHON XPR CNC

COE 249D Veneer Lathe with the following: -- 27" maximum log diameter, Approx.110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling approx. 35 cubic meters per hour. -- Includes: • Linden step feeder• Small log offset x-y spindle chucks• 27"; maximum log diameter• 1484 big bar• 3 to 1 inner drive ratio• Digital ball feed carriage drive -- Note: Sold without 'charger or drive' included. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in very good condition.

COE 233 Rotary Veneer Lathe. -- 30" Swing and 44" Knife length., -- Turning motor LINCOLN 50 HP 230/460 -- Complete with: Hydraulic unit, all drive motors and controls. -- Includes: veneer knife. - Ideal for peeling short blocks.

144L X 120"D X 144"H (25) Filter Screens (4) 12" X 48", (4) 4-tube light panels(1) Exhaust Fan 1HP 120V

COMEC - LON-LS, ...Horizontal Belt SanderSpecial design for sanding of straight or curved solid wood parts such as: Chair legs, chair backs and other similar & difficult-to-sand parts.10 HP Belt driven motor; 12" dia. contact drum for 10" wide x approx. 140" long abrasive belt; air tracking & belt tensioning. -- Stock is fed over the contact drum with an overhead variable speed, pneumatically tensioned feed wheel. -- Sander belt power: 6.6 kW (9 HP approx.) - 220/440 V, 60-Cy, 3-Ph motor.

COMEC - FAS/2, ...Corner Milling MachineCOMEC FAS is a dedicated milling machine with: Inclinable heads for machining the corner of chair seats. Specifications: -- (2) Heads with: 5.5 HP motor and 40 mm spindle shaft. -- Max. cutter size: 150 mm (5.9"). -- Tilting of milling units: 20°/ +45° in horizontal plane. -- Fixed left hand column to support head unit. -- Max. working height: 200 mm (7.8").

COMEVA - CUBE 3, ...Edgebander (Single Phase)The CUBE 3 from COMEVA is designed to be a very compact "every day" Edgebander. The CUBE 3 Edgebander is operated through a PLC control system with a touchscreen. The machine handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm), The coil feed accepts Edgebanding from 0.4 mm to 2 mm thick; strip material can be hand-fed.Equipped with: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Single motor End Trimming station -- Top & Bottom Trimming -- Top and bottom Buffing. -- Feed speed is variable between 9.8 & 23 FPM (3 - 7 MPM); feed chain pads with replaceable rubberized surface inserts. -- Rubberized holddown rollers with ball bearings for low friction and long life. Work stations: -- Pneumatically operated guillotine for up to 2 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit, 0.3 HP motor. -- Top & Bottom trimming units, (2) 0.5 HP motors. -- Top & Bottom buffing station, (2) 0.16 HP motors. -- Complete with: Safety enclosure protects the operator from noise and debris. Engineered & Manufactured by COMEVA S.L, in Spain.Includes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.

DUST-EX HSAG-24 Packaged Safety Solution for a 22"x22" (24" dia. round equivalent) Return Air Rated for 10,000 CFM. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap Valve (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel. One-Zone CP05 Control Panel 1 inlet, 1 outlet: UL698A Control Panel for use with NFPA 69 compliant Explosion Isolation Valves. Standard panel includes status lights, intrinsically safe circuit (1 Per Zone), monitored inputs (3 total), ability to add a secondary clean air isolation valve, output for system shut down and monitoring, drawings, installation instructions, NEMA 4 outdoor rated enclosure, UL and Canada UL listings. Allows for 120VAC or 24VDC input power. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 39" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) High Speed Abort Gate, EM-HSAG02-24, magnetic (24 VDC), 22" x 22" flanged inlet and outlet (24" round equivalent), control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 10,000 CFM / 3000 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe

DUST-EX HSAG-24 Packaged Safety Solution for a 23"x23" (24" dia. round equivalent. Suitable for up to 25" dia. ) Return Air Rated for max 12,850 CFM @ 3,500 FPM.. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Heavy Duty Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel, Intrinsically Safe, CP05 - single zone, allows for installation of (1) inlet and (1) outlet explosion isolation valve(s), (3) monitored inputs per zone (two programmable), (1) intrinsic circuit with barrier and physical separation (one per zone), outputs for system shut down and monitoring, NEMA 4 enclosure, 120 VAC or 24 VDC. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 40" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK-02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) Heavy Duty High Speed Abort Gate, RGAG-23, magnetic , 23" x 23" flanged inlet and outlet (24" round equivalent), suitable for 21" - 25" dia., control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 12,850 CFM @ 3,500 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe (broken bag detector) RS-PDP03, RS-MK02DP, etc. IP 65 encl

DYNMA AIRKOMP CASE CLAMP (SEMI-AUTOMATIC): -- The lamellar Case Clamp solves one of the big problems with Case Clamp assembly; it eliminates setup time. If you have ever struggled or are struggling with an old Clamp, you know how time consuming cabinet assembly can be.Before clamping each different cabinet size, several adjustments have to be made; this means loosening and tightening each individual clamping pressure point.Specifications: -- Length min. cap. is 13.1" (335 mm) & max. 97.2" (2,470 mm)"; Height min. cap. is 11.8" (300 mm) & max. 54.3" (1,380 mm); Depth min. 7.9" (200 mm) & max. cap. is 27.5". (700 mm). -- This multi-purpose Case Clamp with interlocking vertical & horizontal pressure beams is specially designed to save time and labor. -- Clamping pressure is applied across the entire vertical and horizontal beams for the clamping of case goods, drawers, etc.Pressing Elements: -- Vertical platform with (6) intercrossed steel pieces 6" x 1.97" (150 x 50 mm), Horizontal/Lateral column with (5) intercrossed steel pieces 6" x 1.97" (150 x 50 mm). -- Clamping beams move to position on precision trapezoidal threaded spindles and travel at 25 mm (1") per second. -- Timer automatically opens the Clamp at the end of the cycle. -- Max. pressing pressure 1,200 kg / 2,640 lbs (horizontal/lateral), 2,000 kg / 4,400 Lbs (vertical).Operation & Features: -- Operation by selector switches for the following functions: Clamping pressure, Beams up/down, left/right, diagonal, and clamping time. -- A sturdy, stress-free, welded steel frame guarantees square cabinet assembly; -- The motor load for clamping pressure is digitally regulated to minimize the wear associated with clamps having standard clutch braking. -- Actual model is DYNMA AIRCOMP

EARTH CARE PRODUCTS, INC. "DB-1030" (10.5 Ft. x 32 Ft.) TRIPLE-PASS DRYING SYSTEM, W/GAS BURNER:Complete with the following major components: -- 10.5 Ft. x 32 Ft. (despite the model DB-1030) Triple-pass Insulated drum. -- Trunnion Bases, and 30 HP Drum Drive. -- High efficiency Cyclone, Cyclone outlet Airlock. -- 100 HP Dryer Main Fan, and Ducting. -- 25 MM BTU Gas Burner complete with Refractory Lined Furnace and Gas Train. Notes: The Trunnion Tracks and Trunnion Wheels are in good condition as is the drum interior. The system was renovated in 2015 and not used much after the work was done. The equipment is still in-place.

EKSTROM / CARLSON - 18, ...Pump Sander Pump Sander with: (2) 1" Dia. horizontal spindle; 2 HP - 1,200 RPM enclosed motor; mounted on heavy cast iron pedestal. -- Complete with: Push button magnetic controls & starter; 4" dust collection port.

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 3-1/4"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 280 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition.

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 4-1/2"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 250 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition. -- 3 extra blades

ELGI EN07-125 10 HP Rotary Screw Compressor; 38 CFM @ 125 PSIG.Equipped with: -- Efficient air filtration system where air enters through a pre-filtered enclosure. -- After cooler is standard on all models to enable high efficiency TEFC, Super E, 10 HP motor operation up to 115°F ambient temperature.Complete with: -- "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Includes service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely.Includes: -- 3-Stage efficient air-oil separation (less than 2 PPM). -- Single door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: F10104 / MICRO 50 Clean Resources F10104 / Micro 50 Clean Resources F10104 Oil/Water Condensate Separator - add;...$ 500

ELGI EG30-125 Rotary Screw Air Compressor; 40 HP - 170 CFM @ 125 PSIG40 HP Rotary Screw Compressor (Direct Drive); Air-End equipped with "eta-V" profile rotors. Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty

ELGI EN07-125 10 HP ENCAP Rotary Screw Compressor w/Tank & Dryer; 38 CFM @ 125 PSIG.ELGI's 10 HP Rotary Screw Air Compressor w/20 CFM Refrigerated Dryer mounted on a 120 gal. receiver tank. -- Equipped with: 10 HP motor operation up to 115°F ambient temperature; "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely. -- Includes: 120 Gal. receiver tank, 40 CFM Refrigerated Air Dryer; single-door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: -- [F10104 / MICRO 50] Clean Resources F10104 / Micro 50, Clean Resources F10104 Oil/Water Condensate Separator - Add $ 305Designed for smaller compressed air systems. This system was designed as an economical solution for small compressed air systems, up to 125 psi. Theproduct offerings also include a factory-installed and plumbed wall bracket, reducing installation time. Replacement cartridges provide easy, no messmaintenance and offer the lowest life cycle cost in the industry.

ELGI EG75-125 Rotary Screw Air Compressor; 100 HP - 453 CFM @ 125 PSIG100 HP Rotary Screw Compressor, 450 CFM @ 125 PSIG(Direct Drive); Air-End equipped with "eta-V" profile rotors. -- Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty: Lifetime warranty subject to adherence to conditions outlined below. The scope of lifetime warranty will cover replacement of parts and free of cost labor for 120 months from date of start-up or 126 months from date of shipment from an ELGi warehouse, whichever occurs first. Parts only thereafter.Optional: [F10501 / CRP-500] Clean Resources F10501 / CRP-500 CRP-500 CFM Oil/Water Separator System (Includes DC Plus Manifold Installed) Order Number: 553-12-0047 The Next Generation Molecular Filtration System Compression-fit manifold for precise filtration control Timer drain for improved flow of condensate through the media bed Antimicrobial sanitation of discharge hose to prevent algae growth Twelve available inlets (increased from six) No maintenance or messy bag change-outs Cradle-to-grave warranty System monitoring services - Add ...$ 2,650