BIESSE SPARK 3.3 Edgebander (Compact)0.4 mm to 3 mm Material thickness. Min. panel thickness 10 mm, max. panel thickness 40 mm. Min. panel width 90 mm, min. panel length 140 mm.Equipped with: -- 2 Liter Glue Teflon coated tank with quick heating system. -- Top pressure beam with manual adjustment through numerical read-out equipped with rubberized holddown wheels. -- Pneumatic Guillotine knife for automatic edge cutting with a max thickness of 3 mm with automatic “kickback"; of the edge. -- Adjustable edge pressure unit with (2) rollers: 1st roller motorized with separate adjustable pressure system; 2nd idle roller with separate adjustable pressure system. Workstations: -- Double Motor End Trimming Unit - 2 tilting motors HF 0.5 HP each. -- Top and bottom Trim with (2) HF motors, 0.75 HP (0.55 kW) each and micrometric adjustment with numerical read-out. Cutters with 3 mm radius with (4) knives. -- Top and bottom Buffing station. -- Material feed speed 12 MPM (39 FPM).

BIESSE AKRON 1440 SINGLE SIDE EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + with "AIR FORCE" PUR & EVA TECHNOLOGY: -- Specifications: Latest Technology combines productivity, efficiency, and flexibility for all types of edgebanding material."AirForce" emits high temperature compressed air through a slot nozzle directly onto the reactive layer of laser banding. That layer is activated and bonds the banding to the panel fibers. This technology allows changes based on banding colors without any setup.Environmentally friendly providing a “clean - green"; technology that eliminates glue and fumes, which becomes timely & important. In addition, it features a conventional EVA (Hot Melt) Gluing System to cover the full range of edgebanding processes in use today!Working Capacity: -- Min. panel height: 10 mm; Max. panel height: 60 mm; Height of edgebanding material: 14 - 64 mm; Thickness of edgebanding material in rolls: 0.4 - 3 mm; Thickness of edgebanding in strips: 0.4 - 10 mm.Min. panel protrusion from the track: 25 mm; Panel length: 140 - 3200 mm; Min. panel width (with length 140 mm): 85 mm; Min. panel width (with length 250 mm): 50 mm.Multi-Feed speed 8-12-15 &18 MPM.Glue & Pressure Section: -- Infrared lamp IRL 700; Gluing unit Quickmelt QM 703 EVA melting glue. Special glue container for PU glue; Additional glue container for EVA gluing unit with melting device.Additionally equipped with the AirForce "VC-710", High pressure, hot air system to reactivate special pre-coated edge material (commonly referred to as laser edge.Automatic edge feed; Cutter knife; Pressure zone with 1-Drive & 2 pressure rollers.Working Units: -- Pre-milling unit with 2 x 0,8 kW, 12000 RPM motors, front/rear inclination 0° -15°. -- RT 02; Gluing, edge feeding, and pressing unit VC-511. -- End trimming unit with 2 x 0,8 kW, 12000 RPM, front/rear, inclination 0° -15°. -- Fine trimming unit 2 × 0,6 kW, 12000 RPM top/bottom. -- (2) Multifunction Corner Rounding unit, 0,65 kW each, for Corner Rounding, Straight Work pieces, Post and Soft-Forming 90° -180° degrees. -- Edge scraper unit; -- Glue scraper unit; -- Buffing unit 2 × 0,37 kW motors. Machine Features: -- Belt pressure beam. The top presser comprises a rubber belt with a stain-proof coating. The thrust exercised on the panel is provided by springs housed on techno polymer connecting rods. -- Auto adjustment of in feed fence. -- Automatic track lubrication system with dynamic track absorption. -- Manual infeed system for narrow pieces. -- One coil automatic edge feeding. -- Hybrid gluing head for granulated EVA and Polyurethane glue. -- Pre-Melter TM10 for Polyurethane glue in cartridges. On-demand top-loading pre-melter for PUR glues. -- Adaptive infra-red lamp to heat up the panel side before the glue application, in order to optimize the adhesion process. -- Independent pneumatic exclusion of the top/bottom fine trimming unit. Operator & Machine Control: -- Biesse, Windows-based "

BIESSE ROXYL 5.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edgebanding Capacity: Edge thickness for strips min./max. 0.4 - 22 mm (0.02" - 0.87"), coiled material from 0.4 - 3 mm (0.02 - 0.12"); panel thickness from 10 - 60 mm (0.39 - 2.36"), workpiece width min. of 85 mm (3.34"); workpiece length min. 140 mm (5.51"); feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM). --Machine Interface:"Roxyl-Matic" Automated machine setup, MS/Windows XP Operating System, floppy drive, and 4 GB HD; USB port, keyboard, and mouse interface. -- Flat Screen (17") with color graphics interface: Programs can be easily created and recalled at will; Graphic interface makes programming easy, icon of each unit may be brought up on the screen to show the operator the status of the unit and the parameters, which can be programmed; Edgebander may be operated manually when required, without necessity to write a program.Machine In-Feed Configuration:Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. -- Anti-Adhesive "ADZ-700" Automatic Spray Unit with: Glue release agent preventing glue to adhere to work piece surfaces. -- Infrared Heating Lamp: Preheating workpiece edge to ensure best possible surface adhesion quality of edgebanding material. -- Edge Magazine: Automatic for processing coiled and strip edgebanding material. -- Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers.Gluing System:EVA (Hot Melt) "QM-705": Quick premelting granulate with glue roller applicator to cover conventional edgebanding material. -- AirForce "VC-710": High pressure, hot air system to reactivate special pre coated edge material (commonly referred to as laser edge).Workstations:End Trimming Unit "IN-801": Front & rear trimming motors, uni-point swivel 0° - 15° bevel, programmable pneumatic change-over from flush to bevel. -- Rough/Flush Trimming Unit "RS-701": Top/Bottom pre- or flush trimming motors. -- Flush/Bevel/Radius Combination Trimming Unit "RF-400": Servo controlled, (2) Servo motors (one for horizontal tool position, one for tool up/down position); using combination bevel/radius/flush insert knives; pre-positioning of motors by pneumatic air cylinders. -- Corner Rounding Unit "CR-202": (2) Motors for front/back corner and upper & lower edge profiling. -- Profile Scraping Unit "RBK-503": Top/Bottom 2-axis NC programmable knife positioning (i.e. 2 - 3 mm radius) for PVC edges. -- Glue Scraping Unit "RCC-701": Flat, top/bottom, digital positioning indicators, pneumatic controlled for in/out position. -- Buffing Station "SP-501": Top & Bottom buffing motors with 150 mm ( 6") cloth buffing wheel diameter; adjusts in multiple directions. -- Edge Reactivation Unit "PH-700": Top/Bottom hot air blowers to restore original color to profile scraped PVC edge material.Complete with: -- Top Pressure Beam with driven flat belt and program

BIESSE AKRON - 435: Edgebander with Corner Rounding0.4 - 3 mm Banding cap., 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3-1/4") min. panel width.Equipped with: -- Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machined. -- Quick-change glue pot system. -- (1) Large 150 mm dia. driven & (5) idle pressure rollers; Edge Feeding & Pressing Unit VC-511: Automatic loading of tape in rolls and strips. -- Feed Speeds: 33 - 46 - 65 FPM.Workstations -- Double motor End Trim; tiltable from 0° - 15°; each motor: 0.8 kW (1 HP) - 12,000 RPM. -- Top & Bottom Trimming Unit with: (2) Motors, 0.65 kW (0.87 HP) each. - "Pro-nesting" copiers; cutters R-2 mm. -- Corner Rounding Unit with: (2) Motors; each 0.65 kW (0.87 HP) - 12,000 RPM. -- Top & Bottom radius scraping. -- Top & Bottom Flat Glue Scrapper. -- Top & Bottom Oscillating Buffing Station: (2) Motors; each 0.5 HP - 2,800 RPM.Operator & Machine Control: -- Operator control panel; High-Definition touchscreen control; Windows XP based; user-friendly graphic user interface with: Diagnostic and assisted maintenance. -- USB End Ethernet port; Controller (max. of 320 programs); soft touch keypad; 6" color LCD screen; displays in millimeter or inch units; automatic or manual startup.Complete with: -- All cutting & trimming workstations: HF (high frequency motors; 200 Hz) and enclosed by padded sound enclosure. -- Top pressure is provided by staggered double row holddown wheels mounted on ball bearings.NOTE: Return Conveyor not included.

BIESSE ROVER B EDGE 1667 CNC MACHINING CENTER (W/EDGEBANDING) -- Specifications:This "Bridge Gantry" machine is "IDEAL" for window, stair, door & component parts manufacturing:Working Field considering "all" units when Routing, "X" Axis is 265" (6,735 mm), "Y" axis is 62.9" (1,600 mm), "Z" axis stroke 13.6" (345 mm), max. material thickness when machining 9.6" (245 mm)When "Edge Banding" "X" Axis is 227" (5,780 mm), "Y" axis is 62.9" (1,600 mm), the max. material thickness is 2.3" (60 mm); the minimum internal radius is 30 mm & minimum external radius is 8 mm (depending on flexibility of the banding material). -- Positioning Speed: "X" & "Y" axis is 279 FPM (85 MPM), "Z" axis is 98 FPM (30 MPM); AC Brushless Servo motors with digital drive and linear guides ensure high speeds with a smooth acceleration-and-deceleration. -- Worktable: (8) Vacuum bar support rails with pneumatic lifting blades, (4) "ATS" vacuum pods per rail; set up assistance according to the program to process.(8) Pneumatic pop-up back stops, (8) pneumatic pop-up front stops, (4) pop-up side stops, (2) pop-up central stops create (2) independent work zones.Edge Banding unit:The edgebanding is automatically applied to square or irregularly shaped parts as the CNC head rotates along the "X" "Y" & "Z" axis and simultaneously rotates the tooling up to 360° on a high precision "C" axis.Floating "hot melt" glue pot & application roller with separate thermostats apply glue on the panel edge.Pneumatically controlled pressure roller with manually adjustable guides for coil & strip feeding; numerically controlled with encoder that measures strip feeding process.(1) 4-Coil tape magazine with warning sensor when the end of the spool is near; edge banding unit precisely applies 0.4 - 3 mm ABS & PVC with 60 mm (2.3") max. edge height.Pneumatically activated saw blade performs the end trimming at a 35° angle for precise fitting of overlapping joints on adjoining edges. -- Boring Unit: BH17 Boring Head with 4 HP (3 kW) motor, variable speed from 1,500 - 7,500 RPM; (10) Independent "Quick Change" vertical spindles with (6) spindles in "X" axis & (4) spindles in "Y" axis.(6) Horizontal boring spindles with (2+2) in "X" axis & (1+1) in "Y" axis; (1) "X" axis grooving for up to 120 mm dia blade. -- Machining: (2) 18 HP (13.2 kW) liquid cooled electro-spindle router with HSK F63 adaptor; 1,500 - 24,000 RPM.(1) NC controlled "C" axis for 360° horizontal processing; (1) 22-position ATC tool Plate mounted at the back of the machine. -- Operator & Machine Control: PC Front End with Biesse "BH 660" + "BiesseWORKS Advanced" + "bSOLID" + "bEDGE" + WINDOWS "XP" operating system.15" CRT monitor, full keyboard, mouse, 1.44MB & CD ROM disk drives, RS 232 & USB ports, Ethernet connection.Multitask operating system with specific function controls & and internet trouble shooting capabilities; input/output modules, axes override, 4-axes interpolation, diagnostic graphics aid for programming, machine data & to

BRANDT OPTIMAT KDN 650 C Edgebander, with Corner Rounding, Pre-Melt, & 8,654 Hrs. (As of 6/2/22) Specifications: -- Edgebanding thickness 0.4 - 8 mm (0.02" - 0.31"). -- Panel thickness 8 - 55 mm (0.31" - 2.17"), Min. panel width 65 mm (2.56"), Min. panel length 160 mm (6.30"). -- Feed speeds 11/14 FPM (36/46 FPM). -- Working height 950 mm (37.40").Equipped with: -- 32-1/2" Dia. Coil table. -- Automatic magazine. -- 3 mm (0.12") Guillotine. -- "Quick-Melt" Hot melt glue unit, with Heat-up time: Approx. 12 min., Pre-melt hopper feed, Quick-change hopper & tank for color changes, Reversible glue applicator roller rotation, & Retractable glue roller. -- Pressure section, with (1) Large driven & (3) Small pneumatically-controlled idler rolls. -- "POWER CONTROL PC 20+" Control, with 600 MHz, 256 MB RAM, USB Port, 1 GB Flash card, Internal modem for remote diagnostic access link, & 12" TFT Flat screen monitor. -- Line control (no limit switches) for workstation functions. -- Feed chain, with 2.2 kW (3 HP) Feed motor & Automatic chain track lubrication. -- Digital height indicator. -- Sound enclosure.Workstations: -- Front & rear end trimming unit, with (2) 0.35 kW (1/2 HP) - 12,000 RPM High frequency motors, 0° - 15° Chamfer, & Programmable pneumatic control for straight or chamfer trimming. -- Top & bottom flush trimming unit, with (2) 0.55 kW (3/4 HP) - 11,300 RPM High frequency motors, 0° - 25° Swivel, & Combination straight/radius cutters. -- Corner rounding unit, with (2) 0.35 kW (1/2 HP) - 10,940 RPM High frequency motors & 3 mm (0.12") Radius insert cutters. -- Top & Bottom Profile scraping unit, with Vertical & Horizontal tracing. -- Top & bottom buffing unit, with (2) 1/4 HP - 1,400 RPM Motors and Vertical & Horizontal tilt.

--This machine is in Auction @ https://exfactoryauctions.com/Detail/PM-231011/event/A122024$1. --NO RESERVE! BRIANZOLA SIMCOR 10" W Rotary Embossing Press Specifications: Max. thickness 4" (Depending on head diameter). Equipped with: Slotted table, with 11-1/2” x 3/4” Adjustable left & right material guides. Fixed arbor, with 1 HP - 1,700 RPM - 260/440 V Motor & Adjustable arbor support. 19-1/4” L x Approx. 10” Dia. Motorized smooth steel feed roller synchronized with arbor, Electronically-controlled feed speeds. Complete with: 8” Dia. x 1” W Embossing Head.

BRYAN CL 240-W-GI BOILER, HOT WATER TUBEThis Boiler was taken out of an Office Furniture Factory where it was used to heat drying tunnels to a temp of 120 F.Disconnected and in storage for 1-1/2 years.Details & Specifications:Model: CL240-W-GIInput MBH: 2,160/1,080Output MBH: 1,728BRYAN #: 971292Relief Valve Setting: 50 PSIGHeating Surface: 287 sq/ftMAWP Water: 60 PSIGNational Bond #: 41033Canadian Reg #: E6190.25Gas Data:Natural GasMax Input CFH: 2,160Min. Input CFH: 1,080Min. supply Pressure: 7 In. WCMax supply pressure: 14 In. WCManifold pressure in WC: 3.5Orifice size: DMS 29

BUILDERS AUTOMATION (BAM) 2220 Stair Wedge Cutter. Automatically cuts wood wedges used to lock stair treads and risers into slots in stair stringers.. -- Equipped with: 10" Dia. saw blade with 1.5 HP direct drive motor, hopper feeds material automatically, air operated with 6 CFM compressed air requirement, 1.8 Sec/stroke. -- Features: Auto-shutoff feature and capability to cut glue blocks. -- Upright guide expandable to hold up to 40 pieces of wood at one time -- Rapid changeover to cut glue blocks for more efficient operation -- Once cycle started, hands-free use for labor-saving utilization -- Enables you to easily change size or angle without tools saving time and improving productivity -- Utilizes a 1.5 HP saw that automatically cuts pieces up to 9-1/2" W x 11-1/2" L -- Operator panel includes key start and e-stop controls for the saw motor and start/stop control for the pneumatic system that coordinates all machine motions -- Capable of producing wedges of varying thickness on alternate strokes of the saw -- Scrap material is ejected under the machine, and the wedges are discharged into user-supplied hoppers -- An included discharge chute diverter separates automatically and directs wedges of different thicknesses (produced on alternate saw strokes) into separate hoppers (user-supplied) -- Sawdust carried away from the saw guard pick-up through a 3" diameter hose -- Comes with manufacturer's standard 1-year warranty -- Complete with: Self-diagnostics, built-in starter, automatic shutoff feature, air filter & lubricator.

BUILDERS AUTOMATION MFSR CNC 5-Axis Multi-Function Stair Routing Machine, fully programmable.Specifications: -- Axis Configuration: 1.) X axis; 2.) Y axis; 3.) Top Z (top router depth control); 4.) Bottom Z (bottom router depth control); 5.) Axis A (advancing of board) -- Features: Programmable Touch Screen for simpler stair characteristic input by operator; Touch Screen for landing cut both top & bottom for open box & contemporary; Two (2) high frequency routers with 7.5 HP @ 24,000 RPM fan-cooled spindles that can accommodate shanks of ½" or 3/8" diameter.Accepts one or two stringers at a time -¾", 1", 1½" thick for a total of 3" maximum thickness and 7¾" to 15¾" wide; Extra wide ¾" guide rails for more bearing surface with a 3¼" high fence. -- Includes: (5) Cylinder clamps - 3 fixed and 2 adjustable for up to 2,950 Lbs of vertical stringer clamping force. Additional 1,180 Lbs horizontal clamp force for a total of 4,130 Lbs.; Self-centering feed system on linear bearings for better support and elimination of wear on the brass parts; Accommodates staircase angles from 20° to 45° and riser kickback from 5° to 11° with landing cut; Cuts up to ½" deep in yellow pine at the maximum rate of 20" per second and an open stringer in a single cut;Programmable to cut any combination of box, contemporary, or open stairs with landing cut; Completes the top and bottom landing cut without additional handling or manual sawing. Adjustable setting for wedge fit or material variances. -- Production rate: Approx. cycle time 10 Seconds per 7/11 tread in 1 or 2 stringers. -- Comes with: Dust collection cups on each router for clean efficient operation.Manufacturer's standard 1 year. -- Overall Dimensions/Weight: Measures approx. 8′ x 6′ 5″ x 7′ high; Gross weight approx. 3,500 pounds. -- Services required: Air requirements 15 CFM @ 110 psi, (minimum ¾" diameter unrestricted line);Electrical requirement 230 V, 3-phase at 70 Amps. -- Available Option: Extra wide, custom version that cuts down the middle of up to a 24" wide stringer, yielding two sets with no waste (except sawdust).

BURKLE - VBM 1688, ...Stain Wiping MachineSingle sided machine, 1,600 mm wide; 2-Brush Panel Cleaner (TAMPICO brushes). Features: &#9679 Heads can be positioned as needed spacing between the brushes by sliding brackets. &#9679 Brush raising & lowering accomplished by means of handwheel adjustment. &#9679 Brushes are removed at side of machine by sliding out of shroud/channel support rail. &#9679 Safety bar checks part thickness for overthickness parts. &#9679 SIEMENS Control to set rotation speeds & feed belt speed. &#9679 Rigid Aluminum bolted base construction. &#9679 Solid feed belt (NO vacuum holddown)

BURKLE - Roll Coat, ...Lacquering Line with: UV Curing & HEESEMAN Sander. General Line Data:Working width: 1,300 mm (51")Working height: 900 mm +/- 20 mm (35 - 36")Production speed: 10 MPMPassing height 3 - 80 mm (3/16" - 3-1/4")Shortest length of boards 350 mm (14")Operating side: Right-hand side Electric:Operating voltage: 480 Volt, AC, 60 Cycles, 3-PhaseControl voltage 24 Volt, DC LINE CONFIGURATION:STATION #1 - 2-Roll Coating Machine - "SAS 1300" (Filling Machine) For single-sided application of base coating materials suitable for circulation. The machine is suited for base coating veneered, boardlike workpieces or solid components simultaneously filling fine grain or hairline cracks in the veneer by means of the Reversing Smoothing Roller. Application Unit:- Separate, infinitely adjustable frequency-controlled direct drive for the application roll. Rubber-covered application roll of double thickness of the rubber covering, with corrosion-resisting roller ends.- Quickchange coupling for the application roll with hinged bearings and an OLDHAM coupling. Oscillating scraper blade for the application and doctor rolls with an ergonomically designed scraper blade support is quickly removable for cleaning, and can easily be placed back by a self-locking worm gear.- Separate, infinitely adjustable frequency-controlled direct drive for the reversing Doctor Roller. - Change of rotation of the Forward Doctor Roll by an electric reversing switch in the Control Panel.- Hard chromium-plated doctor roll with a fine adjustment by a worm gear gap adjustment via a mechanical digital indicator in the handwheel.- Hood, which can easily be opened, features integrated radiation protection. Smoothing Unit: - Hard chromium plated smoothing roll with an infinitely adjustable, frequency-controlled direct drive. - Scraper blade for the smoothing roll with an exchangeable plastic blade. - Distance from the smoothing roll to the application roll approx. 0.5 mm, for the automatic return of the material, readjustable when regrinding the application roll. Material Circulation System:- Pneumatic double diaphragm pump (R 1“) with pressure reducing valve & stop for careful lacquer feed, particularly suited for very viscous and solvent-free lacquer systems.- Material supply by means of a chemical resistant hose and special steel pipe, ergonomically designed and fitted underneath the hood, with discharge hose and stop.- Large-dimensioned lateral collecting troughs and return gutter made of special steel.- Spring-loaded end plates with exchangeable screwed-on plastic coverings.- Suitable for one way containers of 30 liters contents (max. height 400 mm). Motorized Height Adjustment:- (2) Separate, motorized precision lifting gears wit

BUSCH MINK MM 1322 A VV8 VACUUM PUMP, ROTARY (DRY CLAW): -- Specifications:360 m³/Hr., Dry Rotary Claw Vacuum Pump, Model: MM 1322 A VV8. Nominal pumping speed displacement 212 ACFM; Ultimate pressure 112.5 TORR; Nominal motor rating 10.9 HP; Nominal motor speed 3,600 RPM;Noise level (ISO 2151) 82 dB(A); Weight approx. 655 Lbs.; Dimensions (L x W x H) 46.9 x 21.5 x 17.9 inches; Gas inlet/outlet, 2" / 1¼" NPT. -- Industry Uses:Woodworking Handling devices, Drying, Handling robots, Clamping on CNC routers, Pneumatic conveying.

BUSCH MINK MM 1322 A VV8 VACUUM PUMP, ROTARY (DRY CLAW): -- Specifications:360 m³/Hr., Dry Rotary Claw Vacuum Pump, Model: MM 1322 A VV8. Nominal pumping speed displacement 212 ACFM; Ultimate pressure 112.5 TORR; Nominal motor rating 10.9 HP; Nominal motor speed 3,600 RPM;Noise level (ISO 2151) 82 dB(A); Weight approx. 655 Lbs.; Dimensions (L x W x H) 46.9 x 21.5 x 17.9 inches; Gas inlet/outlet, 2" / 1¼" NPT. -- Industry Uses:Woodworking Handling devices, Drying, Handling robots, Clamping on CNC routers, Pneumatic conveying.

BUSELLATO B1CNC CNC MACHINING CENTER (UNIVERSAL): -- Specifications: Design Type: Cantilever Style, 49" x 120" universal phenolic machine table, multizone "Universal" vacuum table for use with pods. -- Equipped with:(1) 10 HP ISO 30 Type ATC spindle; variable speed from 3,000 - 18,000 RPM; (7) position side tool magazine; (1) Multispindle boring block (7-vertical, 4-horizontal) with an X-axis grooving Saw. -- PC-Based ControlWith "Windows 2000 Professional", GENESIS EVOLUTION programming software, Rail plan for pod location software, Autolink DXF conversion software, Autobar labeling software, Gencode barcode reading software. -- Complete with:(1) 80 Cubic meter rotary vane Vacuum Pump; assorted tooling; documentation; manuals and applicable software media.NOTE: This machine has very low usage and was used more like a Hobby/R+D CNC Machining Center by the owner.INCLUDES: -- CORAL - CA/3C Dust Collector; (3) canvas filter Bags; (3) HD plastic Collection Bags; 10" dia. intake flange; 3,105 CFM; 5.5 HP motor, 3/220/440 Volt; complete with on/off starter.

BUSELLATO JET 4002 XL CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working Field "X" Axis of 168.1" (4,270 mm); "Y" axis of 47.2" (1,200 mm); "Z" axis stroke 9.8" (250 mm); 6.8" (175 mm) max. material thickness. -- Positioning Speed:"X" Axis at 230 FPM (70 MPM); "Y" axis at 197 FPM (60 MPM); "Z" axis 49 FPM (15 MPM). -- Worktable:(8) Pneumatic locking panel supports, (3) vacuum pods per support.(8) Pneumatic backstops, (2) pneumatic side stops & (2) pneumatic central stops.(4) Independent working zones; jig locking device on (2) work areas. -- Boring Head:(1) 4 HP (3 kW) Motor - 4,000 RPM; (20) vertical spindles with: (12) Spindles in "X" axis & (8) spindles in "Y" axis. -- Machining:(1) Vertically mounted 10 HP (7.5 kW) electro spindle with: ISO-30 Adaptor (0 - 18,000 RPM) with RH or LH rotation; (1) 6-position automatic tool changer.(1) Additional 5 HP (3.8 kW) vertical router; routers are driven by an 11 kW Digital Inverter -- Operator & Machine Control:PC Front-End with: "GENESIS EVOLUTION" 2.2.1 + Windows "NT" Operating System; 15" color monitor; 1.44 MB floppy & 32X CD ROM drives; 8.4 GB hard disk; 64 MB RAM; (2) RS 232 serial ports; integrated modem; Ethernet card, all built into a protective cabinet enclosure.GENESIS Software is continuously online providing real-time information on tool position & error messages, visualization of RPM, current load meter, and more; positioning of panel supports and vacuum cups.Software features: Automatic generation of G & M code, stop & restart, machine diagnostics, automatic optimization, and full graphic display with the possibility to associate up to (11) parameters and programming of up to (2,000) work lines per single program. -- Complete with:Front safety mats that will instantly place machine in "Pause Cycle" when operator steps onto the mats. Safety Perimeter Fencing. Transformer for 480 V. -- Actual Model is: Busellato Jet 4002 XL.

BUSELLATO JET 100 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications:Working field: "X" Axis 120" (3,048 mm); "Y" axis 49" (1,244 mm); "Z" axis 3.9" (100 mm). -- Positioning Speed:"X & Y" Axes 328 FPM (100 MPM) each; "Z" axis 98 FPM (30 MPM); sll units ride on precision guides & ways."X" Axis uses a helical rack-and-pinion system; "Y & Z" axes use ball screws; all axes are driven by digital, brushless AC Servo motors. -- Worktable:(6) Panel supports with: (4) Lifting bars & digital readouts for manual rail & pod locations according to the program. (4) Vacuum pods per support rail; (2) independent working areas. -- Boring Unit:TF 20 Boring head with (14) vertical spindles: (8) Spindles in "X" axis & (6) spindles in "Y" axis.(4) Horizontal spindles with: (1 + 1) in "X" & (1 + 1) in "Y"; (1) "X" axis grooving saw for max 120 mm blade. -- Machining:(1) ISO-30 Spindle(1) 15-Position ATC tool changer mounted at the rear of the machine. -- Operator & Machine Control:PC-Based control with "GENESIS" + Windows "2000" Operating System.Includes Color CRT monitor, full keyboard & mouse; 256 MB RAM, 10 GB hard disk, CD ROM (52X), 1.44 MB floppy drive; (4) serial ports, (1) parallel port, (2) USB ports. "GENESIS" Operating System with: Large onboard program storage, ethernet connection, specific function controls, and internet troubleshooting capabilities. -- Complete with:(1) 100 m³/Hr Vacuum Pump, Bar Code Scanner, Belt Conveyor for scrap removal. -- Actual Model is BUSELLATO JET 100

BUSELLATO JET 4002 XL CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working Field "X" Axis of 168.1" (4,270 mm); "Y" axis of 47.2" (1,200 mm); "Z" axis stroke 9.8" (250 mm); 6.8" (175 mm) max. material thickness. -- Positioning Speed:"X" Axis at 230 FPM (70 MPM); "Y" axis at 197 FPM (60 MPM); "Z" axis 49 FPM (15 MPM). -- Worktable:(8) Pneumatic locking panel supports, (3) vacuum pods per support.(8) Pneumatic backstops, (2) pneumatic side stops & (2) pneumatic central stops.(4) Independent working zones; jig locking device on (2) work areas. -- Boring Head:(1) 4 HP (3 kW) Motor - 4,000 RPM; (20) vertical spindles with: (12) Spindles in "X" axis & (8) spindles in "Y" axis. -- Machining:(1) Vertically mounted 10 HP (7.5 kW) electro spindle with: ISO-30 Adaptor (0 - 18,000 RPM) with RH or LH rotation; (1) 6-position automatic tool changer.(1) Additional 5 HP (3.8 kW) vertical router; routers are driven by an 11 kW Digital Inverter -- Operator & Machine Control:PC Front-End with: "GENESIS EVOLUTION" 2.2.1 + Windows "NT" Operating System; 15" color monitor; 1.44 MB floppy & 32X CD ROM drives; 8.4 GB hard disk; 64 MB RAM; (2) RS 232 serial ports; integrated modem; Ethernet card, all built into a protective cabinet enclosure.GENESIS Software is continuously online providing real-time information on tool position & error messages, visualization of RPM, current load meter, and more; positioning of panel supports and vacuum cups.Software features: Automatic generation of G & M code, stop & restart, machine diagnostics, automatic optimization, and full graphic display with the possibility to associate up to (11) parameters and programming of up to (2,000) work lines per single program. -- Complete with:Front safety mats that will instantly place machine in "Pause Cycle" when operator steps onto the mats. Safety Perimeter Fencing. Transformer for 480 V. -- Actual Model is: Busellato Jet 4002 XL.

BUSELLATO - Junior 60 4-Y, ...CNC Machining CenterControls & Router Head Drive Systems upgraded in 2015Specifications: Max. operating field strokes: X-Axis is 3,200 mm (125.98"); Y-axis is 1,220 mm (48"); Z-axis is 60 mm (2.4"); max. positioning speed on the X-axis is 196 FPM, Y-axis is 164 FPM, and Z-axis is 33 FPM.Equipped with: Boring head with: (27) Independently selectable vertical spindles for face boring; driven by a 4 HP motor; (11) of the spindles are in the Y-axis and (16) spindles are in the X-axis (one shared spindle in X-/Y-axis).Additionally equipped with: (2) 2-Spindle horizontal boring heads: (2) Opposing in X-axis; 64 mm pitch for boring right & left sides. -- (1) 10 HP RH/LH Router and (1) 9.5 HP Router (0 - 18,000 RPM) by solid-state inverter; 5 HP grooving saw. Automatic Tool Changer with: 5-Position tool holder and ISO-30 adapters.Worktable with: (8) Panel supports; ea. with: (3) Vacuum cups, (2) independent work zones, (4) adj. lateral reference stops, (4) center reference stops. -- BUSELLATO CNC Controls.Includes: 14" Color monitor, (2) RS-232 ports, (1) RS-242 serial port, keyboard, floppy & hard drive systems for data management; all built into a protective cabinet enclosure; front & rear photo eyes for operator safety; (2) TRAVAINI EO Vacuum Pumps.NOTE: Seller can help coordinate logistics and loading of machine.

BUSELLATO JET 3006 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications:4' x 10' "Matrix" grid phenolic surface table for "Nested Based Manufacturing". -- Working cap.:"X" Axis is 121.2" (3,080 mm), "Y" axis is 49.2" (1,250 mm), "Z" axis stroke is 8.1" (205 mm); max. panel thickness is 5.9" (140 mm); -- Positioning Speed:Max. programmable speed: "X" & "Y" axis is 328 FPM (100 MPM), "Z" axis is 111 FPM (34 MPM). -- Work Table:(2) independent working areas with locating stop pins on the front & rear - LH & RH sides for positioning of parts on the worktable; prepared for (optional) elevated pods that allow profile & horizontal machining. -- Boring Unit:(16) Independent vertical boring spindles with (8) spindles in "X" axis & (8) spindles in "Y" axis, (4) horizontal spindles with (1+1) spindle in "X" axis & (1+1) in "Y" axis; 120 mm "X" axis grooving saw; inverter controlled variable spindle speed up to 4,000 RPM. -- Machining:(1) 14 HP (10 kW) Vertical electro-spindle router with HSK-F63 adaptor, inverter driven 1,000 - 24,000 RPM with max. torque from 12,000 - 24,000 RPM;(1) 10-position "Ride Along" automatic rotary tool changer for "on-the-fly" ATC. -- Operator & Machine Control:"PC" Front-End with "GENESIS" + Windows '95, '98 & NT operating system; 32-bit Pentium - 400 MHz processor; 4 GB hard drive,15" Color monitor, international keyboard, soft touch keypad & industrial mouse, RS-232 serial port and (1) 1.44 MB floppy disk drive.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible;built-in 1,500 W air conditioner for constant temperature & dust-free environment. -- GENESIS Operating system for real-time multitask processing; programs can be transferred via diskette or downloaded by wire; -- Complete with:(1) 25 HP Dekker V-max vacuum pump, automatic "forced" lubrication system for guides & ball screw; emergency stop rope & pressure sensitive safety mats that will instantly place machine in "pause cycle" when stepped on; sound absorbing protective head enclosure with debris curtain around bottom edge. built-in 1,500 W air conditioner for constant temperature & dust-free environment - Complies with CE norm specifications. -- Actual Model is BUSELLATO JET 3006 RT