STAR V MACHINERY - SLG-2000 36: Linear V-Groover -- SpecificationsWorking table dimensions: 120" Long x 36" wide; working width: 6" - infinite" (152 mm - infinite); working length: 20" - infinite (508 mm - infinite); working thickness: 0.25" - 1.15" (6 - 29 mm).Max. throat clearance for linear & crosscuts: 14-1/2"/24-1/2" (355/622 mm). -- Equipped with: (2) Independent 10 HP - 3,600 RPM saw motors with: "Servo" control adjustment in "Y" axis & manual "Z" axis adjustment.30 mm Dia. arbor x 76 mm (3") clamping length to accommodate wider cove backsplash, triple fold profiles, or using it for hogging and finish cut; 9-1/4" (235 mm) max. cutterhead dia.(1) Saw motor mounted on the front & (1) Saw motor mounted on the back of the 8" x 12" x 1/2" heat treated steel Heavy-Duty overhead support beam.Side-to-side head travels via linear rails & bearings; manual head height adjustment via linear rails & bearings. -- Feeding System(1) 3 HP Variable speed drive belt system with: "Servo" height adjustment; feed rate: 0 - 45 FPM (12 MPM); belt feeder moves workpiece on a precision "aluminum" roller table. -- Tape Applicator (2) Automatic Tape Applicators with: "Servo" adjustment according to the Saw motor position in "Y" axis. -- Operator Interface10" HDMI Touchscreen display for: Start/Stop, On/Off, Feed Speed & Axis Position. -- Complete with:Safety guards and cutter guards; Anti-Kickback Device; Emergency Shutoff line.Dust Collection requirements: 4,200 CFM; Collector outlets on cutter guards: 5" in dia. -- Actual model #: STAR V MACHINERY SLG-2000

STAR V MACHINERY - SCG-1600: Automatic Cross Groover -- Specifications(1) Spindle with: 12 HP - 3,600 RPM Motor; 60" max. crosscut cap.; material thickness: 0.25" - 1.125".(1) Internal 60" stroke Tape Applicator Station. -- 96" Stroke Servo motor driven Rear Pusher Fence (full 60" rear table width); 96" long x 20" front table with: (5) Digital manual stops. -- Rear Fence Movement, Cutter forward Speed Cut/Tape Stroke and All Controls for Start/Stop, On/Off, Axis position Displays on 10" Touch Screen Panel HMI. -- Grooving head up & down movement via pneumatic cylinder with: Linear rail & linear bearings; depth fine adjustment with special threaded adjustable unit. -- Carriage cross travel powered by: 3 HP Hydraulic motor (4 GPM); driven ball screw with: Linear rail & linear bearings; feed rate: 0 - 40 FPM; Heavy-Duty welded frame construction. -- Complete with:Safety guards & cutter guards; pneumatic support fence; (1) Heavy-Duty infeed/outfeed roller tables. Available options at additional cost below:Accessories, Tooling & Tape: Choose and add to machine base price. Cove Corner Plug Jig: ...$ 575 ea. Brazed carbide 90° cutter for up to 1/2" solid surface: ...$ 745. Please specify the material. Brazed carbide cove backsplash cutter for 1/2" solid surface: ...$1,265 ea. Please specify 3/8" or 1/2" radius. Brazed carbide 90° cutter for up to 3/4" wood materials: ...$ 940.00. 90° Insert cutter for up to 1/2" thick material (body only): ...$1,265.00. Requires below inserts.......90° V-Insert for up to 1/2" thick material: ...$32 ea. min. of (12) inserts required: ...$ 384.......Carbide insert cove backsplash cutter head for 1/2" material (body only): ...$1,590 ea. Please specify 3/8 or 1/2 Radius.Requires Below Inserts:......3/8" Cove radius insert for 1/2" thick material: $42 ea. Min. of (12) inserts required. ...$ 504. ......3/8" Double 45° insert for 1/2" thick material: $42 ea. Min. of (12) Inserts required. ...$ 504.......PCD Diamond 90° cutter for up to 1/2" thick material $3,485 ea.......PCD Diamond cove cutter with 1/2" radius for 1/2" thick material: $ 5,645.00 ea. Roll of VAC2MG: 2" (50 mm) wide; 1,025 y (937 m) long roll V-Groove tape: $ 245. ea.& Minimum of (3) rolls per order = $735. -- Actual Model: STAR V MACHINERY - SCG-1600: Automatic Cross Groover

STATE B-4 OSCILLATING SPINDLE SANDER 1.5 HP Motor with manual switch, (9) spindles from 1/4" DIA to 4" DIA., 1,725 RPM spindle rotation, 20" x 24" table tilts 15° up and 45° down, table height 40". Also includes work light

STATE - B-4, ...Oscillating Spindle SanderSpecificationsTilting table design with pedestal floor mount.Table size: 20" x 24".Table height: 40".Table tilt: 15° Up; 45° down.Spindle speed: 1,725 RPM.Vertical oscillation: 1-5/8".Oscillations/Min: 90.Lubrication: Oil bath splash. -- Heavy-Duty 1/2 HP motor; maintenance free; 1,725 RPM; TENV totally enclosed non-vented motor; rated for continuous operation; assuring long term dependable service. -- Safe operator controls; magnetic motor starter with overload protection for save installation.All controls mounted for operator convenience. -- Operator friendly handwheel tilting Engineered worm gear design allows table to be tilted 15° up & 45° down relative to spindle.Easy-to-read scale allows for accurate tilt determination before engaging locking device. A tapered pin locks the table during horizontal sanding operations. -- Safety features: Magnetic motor starter with overload protection; safety labels; well-placed ergonomic controls; 3-throat rings to minimize table-to-spindle clearance; POSITIV-LOK spindles provide safe & quick means of changing spindles. -- Recently cleaned, checked; electrical contacts cleaned; machine partially disassembled cleaned; reassembled & tightened; oil sight glass replaced.Weight: 280 Lbs.

STATE D-30 DISC SANDERDynamically balanced 30" steel disc.Commercial duty direct drive 5 HP motor.Heavy cast iron 14" x 38" table w/miter gauge slot.Easy precise rack and pinion tilting of the work table with 45° down and 30° up.Motorized Rack and pinion adjustment of the table rise & fall. Sanding station is mounted to (2) 3-1/2" heavy columns.Heavy bolt-down cast iron base.

STEEL FAB 400 Gallon Vertical Air Receiving TankSpecifications: -- Tank size 36" Dia. x 6' H.

STEFANI ONE TOUCH HEAVY DUTY PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + PUR/EVA Gluing Technology: -- Basic Specifications: Minimum Panel Spacing 24.625" (630 mm) between panels; Edge Thickness capacity 0.015" - 0.875 (0.4 - 22 mm); Panels thickness (min/max) 0.375" - 2,36" (10 - 60 mm);Minimum Panel Length 5.5" (140 mm), or 8.625" (220 mm) when "Corner Rounding; Processing Track Speed min/max 40 - 82 FPM (12 - 25 MPM) variable feed speed.FRONT-END EQUIPPED WITH: -- 2-Roll/Station Vertical Coil Magazine with "Automatic" change-over. Infeed Panel Heating Lamps. Spraying unit (Anti-sticking liquid). -- Pre-Milling: 4 kW (5.3 HP) - 12,000 RPM x 2 motors, with Diamond Tooling; -- Gluing System: "No-tool" "Quick-Change", Teflon coated Glue Pot; Electronic Controlled "Quick Melt" system with auto Kick-down."PU-BOX L" Gluing Unit Pre-Melting system with "Melt on Demand" for managing both EVA & PUR glue. all managed form the PC control.This unit "INCLUDES" the SPG Glue pot for PUR + the standard glue pot for EVA. "SPG" Glue Pot for managing both EVA & PUR Glue, capable of emptying the glue pot in 8-minutes, through the PC controller & can be disassembled in less then 10-minutes for cleaning & maintenance. -- Pressure Section: PC Servo Controlled with (1) large dia. clutch controlled drive roller and (5) pneumatic pressure idle rollers with opposite tilt traveling on THK guides, all rollers have "JUMP" capacity.Heavy-Duty Guillotine. 35 mm dia. Reversible glue roller for solid wood application, with clamping device to eliminate any glue transfer on the trailing edge.WORKSTATIONS: -- Top Mounted End Trimming:0.8 kW - 12,000 RPM Motors x 2; Motors Automatic Blade tilt from 0° - 22° on horiz. plane. -- Flush Trimming "R-E": "UPGRADED" 1.84 kW - 12,000 RPM motors x 2, Top & Bottom flush trimming station. -- Multi-Edge Finish Trimming: 1.1 kW - 12,000 RPM motors x 2; Top & Bottom bevel/radius trimming station with up to 30° tilt; NC controlled "Multi-Edge" kit for (3) automatic position, straight, 1mm radius & 2mm radius, preset through controller. -- Corner Rounding: (4) Motors (0.35 kW - 12,000 RPM each); 2-postition (1 & 2 mm radius) preset trimming through controller. -- Profile Scraping: NC Controlled, Top & Bottom profile scrapping units with 2-postition (1 & 2 mm radius) adjustment through the controller; PVC shavings collection box; air pressure nozzle to support removal of scrap. -- Glue Scrapers:Top & Bottom pneumatic controlled, flat scraping knives with bearing guide-wheels. -- Hot Air Edge Brightener:To re-embellish the color & help eliminate scrapper marks -- Oscillating Buffing Unit: 0.3 kW - 1,500 RPM motors x 2; Top & Bottom oscillating buffing wheels for cleaning/finishing material edges; units tilt 0° - 10° to prevent wear grooves in the buffing wheels.Operator Interface: -- Stefani "StarTouch" + Windows "XP" operator interface, with NC controlled adjustment for all working units.17' TFT screen; ETHRENET Network c

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6p STEGHERR KSF Closed Halving Joint Cutter (Cross Joint Milling Machine) Specifications: Max. width 53 mm (2.09"), Max. depth 72 mm (2.83"). Table size 9-3/4” x 26” x 34” H. Tool dia. (2) 150 mm (5.91") & (1) 180 mm (7.09"). Spindle speeds 6,300 RPM. Equipped with: (2) 2.2 kW (3 HP) - 3.470 RPM Motors. Hydro-Pneumatic table feed. Pneumatic clamping. Fence. Foot pedal control. Complete with 1740 mm (68.50") Length stop gauge.

STEGHERR - BOF, ...Through Feed Arch MoulderAutomatically feeds arched or curved parts for profiling or sanding. Feeds & contours parts with a radius of 6" or more and a max. material height of 3-1/4". Specifications: -- Feeds & contours parts with a radius of 6" or more and a max. material height of 3-1/4". -- (1) 1-1/4" Horizontal spindle at 5.5 HP - 7,500 or 1,500 RPM for sanding. -- 5" - 6-1/4" Tool dia., 4" spindle length capacity. -- 0.33 HP Feed motor, forward & reverse variable feed speed from 3 - 26 FPM. -- Flexible mounted 5-roller system guides and feeds workpiece. -- Simple setup allows for rapid changeover of different widths, no changeover required when machining same profile onto variety of arch radii. -- Complete with: Overhead hood assembly and dust outlet.Machine is currently wired for 220 Volt / 3 Phase power.

STEGHERR KPP Vertical Edge Gluing Bander; 2,600 mm (102") Working length, 53 mm (2.08") max. workpiece thickness, solid edge material up to 25 mm (1") thick, edge pressure 6 kg/cm (13 Lbs) pressure for the length of 2,500 mm and thickness of 20 mm at 3.5 bar.Specifications: -- Panel and wood strip are positioned into press chamber, maximum edge strip 2" X 1-1/2". -- Foot switch activates the air tube pressing system, and continuous bottom and side pressure evenly distributed over the entire workpiece allows tight glue joints (panel clamping pressure 80 PSI, edge strip clamping pressure 55 PSI). -- Panel heating unit - 850 watts (220 V, 1 Ph) temperature control from 40° - 150° C (104° - 300° F). A moveable clamp gauge positions the edge strip for drop edges or overhangs.Features: -- Special stop gauge allows for the positioning of mitered corners. Average PVAC glue cure time 40 - 70 Seconds.

STEINEMANN OSUS NOVA 160/6 K-FS/NS-OPTIMAT Top and Bottom Calibrating Sander(6) heads consisting in 2 machines, first machine top/bottom opposed head. Secoind machine (4) head with Combi and finishing platenFeatured: -- 2-Head K, (1) top & (1) bottom; both heads directly opposed. for calibrating -- (4) head FS/NS top/bottom first Combi head, second finishing platenSpecifications:First machine Calibrating Sander: -- Top/bottom opposed single head -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on K head 34 M/sec. (6,667 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- 100 HP motor each head. -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine only Second Machine Finishing Sander: -- Top/bottom (2) head each as Combination drum/platen and finishing platen -- Working width 1,600 mm (63") both heads 11" dia. steel contact roll -- Thickness capacity 3 - 150 mm ( 1/8" - 5.9") -- Working height (passline) 1400 mm (55") -- Cutting speed on FS head 22 M/sec. (4,330 SFM) -- Cutting speed on NS head 22M/sec. (4,330 SFM) -- Tolerance within the board +/- 0,075 mm (+/- 0,003") -- No motor installed -- 63" x 103" Abrasive belt size. (to be confirmed) -- Air jet abrasive belt tracking. -- Variable feed speed 7 - 43 M/min. (24' -138"/min.), 20 HP feed motor,. -- Control panel for this machine Not included: -- infeed and outfeed conveyor -- Conveyor between the machine -- “all the control wiring goes into a cabinet that is separate on each machine. That is just the wiring for the sensors and solenoids for braking and belt tracking stuff. There are no motor controls with these so there are no starters included. The 2 head comes with (2) 150 HP motors and the 4 head has no motors on it. In order to make these operational you would need a PLC and HMI to run the controls and motor starters and would need to buy motor controls

2023 Stema "Alphard" CNC Machine for Drilling, Routing & Tenoning on Doors & Frames Description: CNC haunch/mortise/Tenon/dowel machine for cabinet doors, beaded face frames, full size door mortice/tenon, French miters, dowel insertion. X-Axis w/ 3200mm of Stroke 70 m/min Y-Axis w/ Ballscrew Movement 25 m/min Z-Axis, 25 m/min Ten-Position Automatic Tool Changer/Revolver Tool Changer Allows for Tenoning, Profiling, Mortising, Drilling Haunching Unit (for French Miter Product), 5.5 HP Motor Dowel Insertion Unit (8mm) Vibrating Dowel Hopper Glue Inserting Unit PC User-Interface w/ Windows 10, USB, & 19"; LCD Screen Pegasus Software Total Working Length 3200mm (120") Manually Adjustable Pneumatic Clamps Heavy Steel Frame

STETON P150C Two Platen Cold Press. (Was made as a hot press but heating is not working!) -- Approx. 118" x 51" (3500 x 1300 mm) overall platen size, side loading on 118" side. Pressure from bottom. 2 HP hydraulic pump. -- Maximum daylight opening 450 mm. (17"), less thickness of middle platen. Total pressure: 150 tons. -- Number of cylinders; eight (8). Dia. of cylinders: 3.35" (85 mm) -- Platen material: aluminum. -- Parallel guidance by toothed rack: Yes -- Pressing time selectable: Yes -- Pressing force: Electro-Hydraulic -- Technical type: Upstroking press -- Boiler: Approx 30 KW but heating is not working --Weight: 6.500 KG (14,300 Lbs)

STETON P85 Hydraulic Cold PressDual platen hydraulic cold press -- Platen size 1,300 mm X 2,500 mm (51" X 98") Overall platen size -- Side loading on 98" side. -- 420 mm (16.5") Max. daylight opening. -- Pressure from bottom (4) 3.34" diameter upstroke hydraulic pistons. 2 HP hydraulic pump. 90 PSI.

STRIEBIG COMPACT Vertical Panel Saw (15' Cut Cap.)Specifications: -- 4 HP motor with automatic STAR-DELTA starter electric brake (stops within 4 Sec). -- 181" Rip cap., 64" crosscut; 2-3/8" (60 mm) cutting depth; 250 MM dia. (9-7/8") blade with 30 mm bore - 5,400 RPM rotation. Equipped with: -- Full length center measuring rail with mid level flip-out small parts support shelf; special long-wing crosscut measuring stop, crosscut lock-in stations in 40" increments. -- Automatic mechanically shifting support grid with replaceable lath tips for rip-cuts. -- Specially designed measuring flip stop for use with small parts; (6) Template bar stops for setting common rip cuts; split center shelf useful for staging material; auto-engaging splitting wedge (riving knife)Complete with: -- Heavy Duty panel support roller system (1,200 Lbs cap.) with integral panel stop brake; -- Dust extraction system to rear of frame (requires a bag or dust collector); 4" dust extraction connection. Includes: -- (3) Adjustable base & rear supports for free-standing installation of the one-piece fully welded frame. -- Dismantling and loading onto flat bed truck.Actual model is STRIEBIG Compact 5207.

STRIEBIG COMPACT Vertical Panel Saw (15' Cut Cap.)Specifications: -- 4 HP motor with automatic STAR-DELTA starter electric brake (stops within 4 Sec). -- 181" Rip cap., 64" crosscut; 2-3/8" (60 mm) cutting depth; 250 MM dia. (9-7/8") blade with 30 mm bore - 5,400 RPM rotation. Equipped with: -- Full length center measuring rail with mid level flip-out small parts support shelf; special long-wing crosscut measuring stop, crosscut lock-in stations in 40" increments. -- Automatic mechanically shifting support grid with replaceable lath tips for rip-cuts. -- Specially designed measuring flip stop for use with small parts; (6) Template bar stops for setting common rip cuts; split center shelf useful for staging material; auto-engaging splitting wedge (riving knife)Complete with: -- Heavy Duty panel support roller system (1,200 Lbs cap.) with integral panel stop brake; -- Dust extraction system to rear of frame (requires a bag or dust collector); 4" dust extraction connection. Includes: -- (3) Adjustable base & rear supports for free-standing installation of the one-piece fully welded frame. -- Dismantling and loading onto flat bed truck.Actual model is STRIEBIG Compact 5207.

VITAP ALFA - 27: Construction/Line Borer27-Spindle boring head on 32 mm centers; drills vertically from bottom-up and head rotates to horizontal position for edge boring; head rotation is pneumatic with switch control. -- 2-3/4" Max. drilling depth; 2-1/2 HP - 2,800 RPM motor; pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size; max. workpiece width 31-1/2". -- Equipped with: Left- & right-side fences for construction boring; (2) pneumatic holddown clamps; 118" line boring fence w/flip stops; pneumatic foot pedal control; magnetic starter; overload protection.

VALPATO LBK-150-ST 1 Feed Through Profile SanderTECHNICAL FEATURES: An added small needle type drum sander can be fitted with drum sanding aggregates of 25, ­30, ­35,­40, ­45 ­50 mm diameters which can be used for tighter curves and smaller radius sanding requirements. Storage compartments (2 in total) are located on each machine extremities, these are easily accessible and can be used for sanding belts and various tooling storage. Sanding belt motor power: 3 Kw Abrasive head motor power: 1.5 Kw Oscillation motor power: 0.38 Kw Feed motor power: 0.75 Kw Motor power for electrical adjustment of sanding group: 0.19 Kw Machine voltage: 480/3/60 Full Load Amps @ 480V: 15A Compressed air: Not required Dust collection requirement one (1) only 6" (150mm) port: 950 CFM Sanding belt speed: 14 Mt/sec Variable speed of the belt: from 5 to 25 m/min Sanding belt dimensions: 150 x 2640 mm Height of working table: 930 mm Dimensions of front working table: 1980 x 250 mm Machine dimensions: 2500 x 900 x 1600 mm Net weight: 1000 KMAIN FEATURES: User friendly PLC touch screen control panel is accessible from 360° by the operator, the control panel is centrally located on the infeed end of the machine. Factory installed variable feed drive (VFD), enables machine to run from 5 M/Min to 25M/min (+/­ 80 ft/Min). The entire sanding plenum rise and fall is motorized, it can be adjusted vertically in height to utilise the full height/width of the sanding belt. An oiling unit ensure long life of sanding plenum rise and fall master cylinder.

VOORWOOD M 15A CNC Round End Tenoner & Mortiser for 45° Door --The "M15A" Miter Machine is designed to rapidly make mortise and tenon cuts at 0°, 45° Only, . Parts can be up to 1.5"; thick and up to 4"; wide, and of ANY length. --A primary application for this machine is for miter cabinet door frames. Parts can be quickly transferred from left to right. They are mortised on the left side of the machine and tenoned on the right. The machine can also mill the slots. --Specifications & Equipped with: -- The mortise station has (3) servo-controlled axes (X, Y, and Z) that are coordinated by the machine controller to achieve complex CNC motion. It is equipped with a collet-style router spindle for cutting. The tenon station uses the same X- and Y-servo-controlled axes as the mortise station and is configured for pneumatically actuated in-and-out movement along the Z-axis. The tenon station is equipped with a direct drive shaper spindle for cutting. -- -- Pneumatic clamping assemblies with non-marring urethane pads are mounted to the hold-down assembly to secure the parts during cutting and these can be adjusted to various locations over the cutting surface. -- -- M15 Miter Machine operator interface consists of a colored touch screen. For simplicity, the entire calibration, setup, and monitoring of the machine are accomplished using only four touchscreen displays. The program designs the depth and location of both the mortise and the tenon. When the design is complete, it is saved in a recipe format. Once this recipe is opened, the operation is as simple and boils down to feeding the substrate into the machine. -- -- The full-color touchscreen panel is located on the front of the machine to provide easy access for setting up or operating the machine. Clamping and shaping operations are controlled by operating lighted pushbutton switches.

VOORWOOD A212 FEED THROUGH SINGLED SIDED SHAPE AND SAND. FEEDS FROM RIGHT TO LEFTEquipped with: (4) workstations: (2) 5 HP - 6,000 RPM Shaping stations with 1-1/4" dia. x 2-3/8" long spindles, max. cutterhead dia. 6"; (2) 1 HP - 1,500 RPM sanding stations with 1-1/4" dia. x 4" long spindles. -- All spindles are 5-3/4" horizontally and 2-1/2" vertically, preset 20ø angle on all units; 1 HP feed motor with 0 - 35 FPM variable feed speed. -- Capacity: 5" x 5" Min. part size, 1/8" to 1-1/2" max. thickness, 1-3/4" max. profile face.Also included: Equipment is in good working order and is still under power as noted in the video. There is a variety of cutters included with the sale of machine, and also the return conveyor is included. Cutter heads are as seen in the photos and replacement knives. Also included are TURBO SAND Heads and sanding strips as well as the owners manual. The return conveyor has a single phase 110V roller at the top of the transfer and a 230V 3PH non-marking belt. a Formica top stand to catch doors returned included too. Machine A212: 40"W x 102"L x 69"HConveyor: 44"W x 87"L x 25 1/2"HTransfer Table: 37"W x 41"L x 36 1/2"HCatch Stand: 33 1/2"W x 27"L x 24 1/4 " HAssembled Footprint: 87"W x 144"L