Precision Disc Scalping Screen Model PDS648 48” wide x approx 8’ long 6 shafts and the discs are stitch welded on

Precision 8x16 Screen

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper dissc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though... The photo's show the optional extended shaft and hydraulic starting motor which is a special feature....

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

Precision 58" Chipper - Model 58-60-16 6 Knife 150 HP Motor

System includes: - Infeed System: Volumetric Feed Hopper, adjustable front gate, flow regulator, 43' Infeed Conveyor Belt System, flow regulator and transition chute. - Bagging System: Feeder with scraper, stand alone Volumetric hopper, manual feed system, chute for small bags, additional chute for bulk bags (supported by forklift), rolling system to fill either small or bulk bags, hot air sealer system (14"-28" wide bags) - Palletizing System: In-line turner conveyor, horizontal bag flattener, 8' gravity roller conveyor - System is set up for 575 V service

Premier Tech Form, Fill & Seal Bagger: Model FFS-200 Robotic Palletizing system model AP-425 Dismantled and ready to ship!

D 100 Diesel

CTR Delimber

Prentice 2190 Track Harvester CAT 6.6 Alert Engine 11,000 hours repairs: New motor, final drives, ECM, wiring harness 16,000 hours repairs: New injectors, injection pump, water pump, measuring system, fuel filter housing, top rollers (All work done by CAT)

This saw is no longer required at the current facility. Available for immediate removal! - Prescott Vertical Resaw - 10" Silver Tooth blades; 37'7" Long - 72" Bandwheels - 250 HP Motor - no starter

Pressley 5- blade Trim Saw

Prime Conveyor Pallet Unstacker/Stacker - (2) Available Conveyors

PRS Dual Max Trim Saw with Conveyors

SPECIFICATIONS: - Chip Capacity: 50 LBS/HR - Puck Size: 2? - Chamber Size: 16? X 6? - Puck Exit Conveyor: 6' X 6? - Approximate Floor Space: 5’8? LR X 4' FB X 6’2? H - Electrics: 480 Volt, 3 Ph, 60 Cyc Allen Bradley Panelview 300 Controller

Quick Clamp Carrier Model: SA-CCFP-10.5-14 10.5' Wide 14 Section Clamp: 2.5" high jaw, 38" opening Pneumatic clamp tightener Pneumatic Panel Flattener Electric Drive

Quick Clamp Rack 12' Wide Clamp: 3.5" wide, 40" opening

Quickwood Pro 1100 Sander

Quickwood RO 1300 Sander

Quickwood Pro 1600 Sander