Equipment For Sale

WARATAH 616 HEAD CAME OFF A JOHN DEERE 703J UPGRADED TO A 6222 HEAD RECENT 2 NRE ROLLER MOTORS RECENT COUNTER WIRE SOME NEW PINS

WEB MECAHNICAL JET 10M Jet Air Oven Supply Side complete with the following: -- 400,000 BTUH rating, 3,200 CFM forward curved blower, 5 HP motor 575 V /3 Ph /60 Cy. -- Inlet filter section HEPA 99% DOP rated, Magnehelic gauge across the filter section. -- Thermometer to show outlet temperature, Thermostat to set and control temperature design from 60° -70° C, -- Jets designed to control flow across the belts. Exhaust Side complete with the following: -- Vane axial fan set to exhaust 600 CFM,1/2 HP motor. -- Direct drive fan with motor out of air stream, external grease fittings for lubrication.Heating Module: -- Air makeup sized for 3,200 CFM, 2 HP motor, rated for 400,000 BTUH. --Fan to exhaust through 2"; pleated filter and 12"; HEPA filter, Down discharge,3 HP motor, 3,200 CFM @ 2.0"; E.S.P. -- Engineered for 90° F temperature rise, 0.4 MBTU/hr hydronic coil, features FUJI temperature selector. Conveyor: -- Robust 10-gage steel frame, Novo 40 grey belt designed for up to 90° C and with Auto tracking mechanism. -- Large size 6"; driver and idler pulleys, Support pulleys 3"; as required. -- Heavy duty NORD gear box and a 2 HP direct coupled motor. OPTIONAL (Not included in Price):IR Adder (Lamps): -- Three (3) MW IR lamps in the center of the oven, Three (3) MW IR lamps at the end of the oven, -- Heated length of lamps 54";, dual gold plated element, 3,200 watts per bulb. -- Lamps are designed to sit between the jets on the oven with lamps 8"; (200 mm) above belt and 8"; apart. - Please add ...$ 7,700Control Panel for the above (600 V - Electric) complete with: -- Line interlock, E-stop, fuses, disconnect switch, DC power supply. -- Phase angle controller to control two (2) banks of three (3) lamps. CSA approved panel. - Please add ...$ 12,100BOILER: -- One (1) RBI dominator boiler "DB 600" to supply up to 600,000 BTUH. - Please add ...$ 18,900

WEB MECHANICAL HYDRONIC OVEN - Low Velocity Flash Off - STAGE # 1 and High Velocity Bake Oven - STAGE # 2 STAGE # 1, Low Velocity Flash Off Oven. -- The oven consist of one (1) only hot water oven, 14' wide x 9' high x 30' long with Air flow requirement of 30 FPM/ 9,000 CFM.Supply side complete with the following: -- 400 000 BTUH heat exchanger -- Motor/blower, 2 HP 575 V / 3 Ph / 60 Hz -- Thermometer to show outlet temperature -- Thermostat to set and control temperature to design temperature -- RTD's (1) for accurate oven dispersion temperature -- Eighteen gage galvanized steel panels -- Perforated metal side walls for even air distribution -- Design temperature of 30 -40°C -- Adjustable inlet mixing damper with intake filter (70% recycle) -- Exhaust fan for combustible gasesExhaust will be complete with the following: -- Size 14 direct drive aluminum fan wheelset to exhaust 30% of the contaminated airflow (2,500 CFM) -- Direct drive with the motor out of air stream -- External grease fittings -- Fan module c/w aluminum extrusions and galvanized panels, and will be complete with HEPA style filter, -- DWDI fan, space for hot water heat exchanger STAGE 2 HIGH-VELOCITY OVEN BAKEThe oven consist of one (1) only hot water oven, 14' wide x 9' high x 20' long with Air flow requirement of 50 FPM/ 9,000 CFM Supply side will be complete with the following: -- 1,500,000 BTUH heat exchanger -- 10,000 CFM -- Motor/ blower 5 HP 575v / 3 Ph / 60 Hz -- Thermometer to show outlet temperature -- Thermostat to set and control temperature to design temperature -- Eighteen gage galvanized steel panels c/w 3" insulation -- Perforated metal side walls for even air distribution -- Design temperature of 40 - 60C 104 - 140 F -- Adjustable inlet mixing damper with intake filter (85% recycle) -- Exhaust fan for combustible gases Exhaust will be complete with the following: -- -- -- Size 12 direct drive aluminum fan wheelset to exhaust 15% of the contaminated airflow (1,500) CFM) -- Direct drive with motor out of air stream -- External grease fittings There will be two (2) air knives one at start of the oven and one art the exit to control heat and fume exhaust Air knives will be complete with Multivee filters for inlet air Fan module c/w aluminum extrusions and galvanized panels will be complete with HEPA style filters, DWDI fan, space for hot water heat exchanger.

Webb Dryer System

10x40 Triple Pass Drum Dryer Webb Dust Burner All piping and controls Cyclone Additional blower Airlock

Webster vibrating conveyor, 18" wide pan x 20' long, electric drive, good working condition

Webster Vibrating Conveyor 50' long x 18" wide Includes Chipper Transition

Webster Vibrating Conveyor 18” Bottom, 57’ Length

Webster 24" wide pan x 35' long, 10" sides, electric drive, good condition

(2) Webster 18’ x 30’ Vibration Conveyor

Webster 30" x 25' Vibrating Conveyor

Weeke ABD 050

--MAKE AN OFFER!--VERY GOOD CONDITION AND LOW HOURS!-- WEEKE ABD 050/12/NA CNC BORE, GLUE & DOWEL INSERTER, with 350 Hrs. Only!: Specifications: (1) Horizontal drilling aggregate with (1) individual spindle with 0.55 kW (3/4 HP) - 2,750 RPM Motor; (1) glue & dowel injector with glue flow control; (1) MAFU “MRA 250” vibrating hopper dowel feeder, with Bowl size 14-1/2” Dia. x 4-1/2” D. Working Capacity: Part size: Length 20 mm - 1,250 mm (.75" - 49") Width 50 mm - 800 mm (2" - 31.5") Thickness 10 mm - 60 mm (.4" - 2.4") thick. Machine is set up for 8 mm Dia. x 30 or 35 mm long dowels Work Area (2) Separate working fields with (4) 3-1/8” x 4-5/8” pneumatic top clamps can process up to (4) parts independently on the left-hand, right-hand or center-stops; work can be loaded in (1) field while being machined in the other to allow fast production of varying parts. Operator & Machine Control: PC Front-end with Homag Power Control PC 85T, WoodWOP 5.0 operating system with graphic programming & error messaging; 17" TFT flat screen monitor; Software allows program design with automatic mirror-image by use of an active center stop located 600 mm (23.6") from zero. Complete with: HONEYWELL “HYPERION 1300G-2” Bar code control reader. All manuals, documentation & program disk provided with machine. Actual Model is WEEKE ABD 050/12/NA CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars

Weeke ABD 060 Bore & Dowel Machine This machine will be available in December 2023. - CNC DOWEL INSERTER FOR HORIZONTAL DRILLING AND DOWEL INSERTING - ENGINEERED TO SPRAY GLUE OR WATER - FEATURES A SORBTECH MAIN BEAM TO MINIMIZE VIBRATION - PNEUMATIC CONTROL OF CEBTER STOP AND RIGHT AND LEFT FENCES - OPEN END TABLE FOR MACHINING PARTS LONGER THAN 48” - VIBRATING HOPPER FOR AUTOMATIC FEEDING OF DOWELS - LARGER 17” DISPLAY AND WOODWOP PROGRAMMING - SERVO CONTROL OF DRILL HEIGHT AND DRILL DEPTH VIA PROGRAM - 3 INDEPENDENT SPINDLES ON 32MM CENTERS - BAR CODE READER

WEEKE BHC 350 4/10 CNC MACHINING CENTER: Specifications: -- Working cap.:"X" axis: 3,750 mm (147.6"), "Y" axis: 1,250 mm (49.2"), 80 mm (3.1") max. material thickness. -- Positioning Speed: "X" axis is 196 FPM (60 MPM), "Y" axis 164 FPM (50 MPM) & "Z" axis 66 FPM (20 MPM). The heads travels on THK linear motion guides on all axes. -- Worktable: (6) Moveable support rails, raise-and-lower panel feeding rails, (3) matrix style vacuum pods per rail.(6) Pneumatic backstops, (6) Pneumatic front stops, (2) movable pneumatic side stops, and the dual central zero-stop creates (2) working zones. -- Boring Unit:(1) 3.5 HP, 1,500 - 7,000 RPM Motor; equipped with (24) independent vertical spindles with (16) spindles in "X" axis & (8) spindles in "Y" axis.(4) Horizontal spindles with (1+1) in the "X" axis & (1+1) in "Y" axis;(1) "X" axis grooving saw for max. 100 mm dia. blade, 2,000 - 7,000 RPM. -- Machining:(1) 8 HP HSK F63 Liquid cooled electro-spindle powered by KEB frequency inverter, programmable from 1,200 - 18,000 RPM (constant torque from 9,000 - 18,000 RPM), RH or LH rotation. -- Operator & Machine Control:IPC control with "WEEKE MCC" + Windows "XP" + WoodWOP 5.0 operating system; 15" high resolution color graphic monitor, standard keyboard & mouse for data entry, 1.44MB floppy disk drive, CD ROM drive.EtherNET interface for possible LAN connection to office PC, RS-232 serial interface for simple PC connection; all mounted in separate free-standing control cabinet.WoodWOP allows for the machine to be programmed off-line with the same intuitive icon driven software that the operator has on the machine controller."BECKHOFF" programmable logic control (PLC) operating system for (3) axes; linear, circular & helical interpolation. -- Complete with:(1) 100 m³/Hr Vacuum pump, man-height safety enclosure around rear & sides of machine, 2-zone safety mats (will stop machine if operator enters work area). Actual Model is WEEKE BHC 350 4/10 .

Weeke BHC 550 CNC Router S/N 0-250-13-0781 Out and ready to Load.

X-Axis Travel: 100? Y-Axis Travel: 68? Z-Axis Travel: 9? Max Workpiece Thickness: 4? Spindle Speed: 1,250 – 24,000 rpm Equipped With: Powerful HSK Router Spindle- Up to 9 kW 6 Pneumatically Fixed Work Piece Supports Safety Positioning of Work Piece Consoles and Vacuum Cups

WEEKE BHP 200 FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications:5' x 12' Bridge style gantry machine with User-Friendly "S/C Tech" "MATRIX" grooved phenolic vacuum table. -- Working Area:'X" Axis 145.6" (3,700 mm), "Y" axis 61" (1,550 mm), "Z" axis stroke is 12.8" (325 mm), max. material thickness of 4" (100 mm). -- Positioning Speed:"X" Axis is 164 FPM (50 MPM), "Y" axis is 131 FPM (40 MPM), "Z" axis 66 FPM (20 MPM);The head travels via AC brushless drives & THK linear motion guides on all axes. -- Worktable: User-Friendly "S/C Tech "MATRIX" grooved phenolic vacuum table for easy vacuum pod placement, divided into (2) work zones.(4) Front pneumatic pop-up positioning stops, (2) side pneumatic pop-up positioning stops & (4) back pneumatic pop-up positioning stops. -- Boring Unit:(1) 4 HP (3 kW) motor, variable speed for 1,500 - 7,500 RPM;(10) Independent vertical spindle with (5) in "X" axis & (5) in "Y" axis. -- Machining:(1) 12 HP (9 kW) High speed constant duty Router with HSK F63 adaptor,1,250 - 24,000 RPM, constant torque achieved at 9,000 RPM, RH or LH rotation(1) 8-Position tool changer magazine located at the back side of the spindle carriage.Router is powered by an 14 kW programmable frequency inverter. -- Machine & Operator Control:PC Front-End with WEEKE "PC 85T" + Windows "XP" + WoodWOP 5.0 operating system.17" TFT Color graphic monitor, keyboard for data entry, PC 85T hand control pendant; CD R/W & floppy drives, EtherNET interface for LAN connection to office PC, RS-232 serial interface, USB ports. -- Complete with:(1) 500 m³/Hr Vacuum pump, safety mats & safety fencing. -- Actual model is WEEKE BHP 200

Weeke Vantech 480 CNC Router 4x8 Table

Weeke Profi BHP 007/510 CNC Router