Biomass Equipment For Sale

New remote All outriggers intact and work. Two lower green wear plates worn but being replaced New radiator screen (pictured) will be installed.

Remote control

Monitor shows 5853 hours, serviced, ready to work

This machine is 100% redone. Completly rebuilt motor, new pumps, hoses, wiring harness. New knives and infeed chain

2017 Peterson Pacific 4300 Whole Tree Chipper, Micro Chipper, New Rebuilt Cat C-18 Engine, 785 HP, Under 50 Hours, Frame Hours 10,500 Hours, Air Compressor on the machine, Ready to Chip Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2011 Peterson Pacific Horizontal Grinder Power Source: Diesel Engine Mfr: Cat Engine Model: C27 Horsepower: 1000 Has approximate 9050 hours

JUST REBUILT - CALL FOR DETAILS CAT C27 ORIGINAL HOURS - 1050 HP - TIER 3 NO DEF TOO MANY NEW PARTS TO NAME REBUILT TROUGH, NEW PT CLUTCH, NEW PUMPS (ALL), NEW WIRING HARNESS, NEW DRAG CHAIN, FEED BED, ALL HOSES, GRATES, COMPRESSOR AND MORE.

Machine recently had a New Crate Engine installed prior to fire and during the install the mill was completely reworked, rods,hammers, new wear plate, chains, chain head pulley This has sustained an engine fire which was contained in the engine compartment. Engine is not recoverable. This machine would be a great candidate for a Rebuild or an ideal Electric Conversation. A last resort would be to part out the machine.

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

Portage & Main Outdoor Wood Stove W/ Wood Chip Feeder

2021 Powerscreen Chieftain 1400 -1900 hours -2 deck vibratory box -Up to 400 tph -54,895lbs whole system -Tier 4 engine (110H.P) -3 Conveyors Main,Tail(fine),Side(midsize/oversize) -Belts in good shape -Clean ready to work unit

2001 Powerscreen 725 Trommel Screen, Equipped with Remaned Deutz 100 HP Turbo Diesel, 1000 Hours, Used 1/2" Screen Cloth, New Sticky Belts, All New Brushes, New Tires, All New Radial Stacker Motor, Ready for Work. Weight 55,116 lb Transport length 638" Transport width 108" Transport height 158" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2005 Powerscreen 1800 Track Unit, Engine is a Caterpillar, 5000 Hours, Grizely Bars on Top Deck, Scalping Screener, Brand New Tailings Conveyor, New Bearing Housing for Shaker, Complete Engine Service done Recently, Ready to Work. Weight 66,139 lbs Transport width 9'6? Transport length 50'11” Transport Height 11'2" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2006 POWERSCREEN CHIEFTAIN 1400 -8785 hours -Hydraulic folding conveyors for quick setup -Screen walkways and access ladders for easy maintenance -Drop-down tail conveyor for screen media changes -Radio-controlled tipping grid -Integrated high-capacity variable-speed belt feeder -Grease-filled 4-bearing,2-deck screenbox -Impressive 400 TPH capacity -Applications Sand & gravel, Blasted rock, River rock, Topsoil, Composted materials, Wood by-products and more!

Precision 58" Chipper - Model 58-60-16 6 Knife 150 HP Motor

2001 PRECISION HUSKY PROGRIND 1000 TUB GRINDER REDUCED 275 HP New Fixed Teeth New Auger Motors Good Tires Runs Well

Precision Husky 23 Chipper Needs engine Has Cummins KT19 650HP

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

1996 Precision Whole Tree Chipper 21" Capacity 700 HP Cummins KTA Twin Turbo Needs Clutch AC Heat Good Feed Rollers Disc Wheel Completely Rebuilt New Anvil New Wire Plate Husky 235 Loader 52" Rotobec Grapple PRICE REDUCED

MLS Number 10237206 Precision Husky ProGrind 4000 Tub Grinder 4092 Hours 500 HP Cat 3406B engine Loader with cab