BioMass Equipment For Sale

2005 Peterson 5410 Grinder -5800 hours -CAT 3412 Engine 1000H.P -Needs a discharge belt -New feed chains -New tip protectors

1999 Peterson Pacific 5000G Chipper -1000 h.p. 3412e engine -8000 hrs since major overhaul -3 flail -Spare flail pump -Load adapters replaced within last 1000 hours -Fan pump replaced 1500 hrs ago,Also has had swing and boom pump replaced -New Ecm has less than 750 hrs -New muffler -New feed roll teeth -New heater and a/c -Spare clutch, Spare belts, Spare pins and Seal kits -Babbit or key knife system -Fleet maintained

2019 Peterson Pacific 2710D Track Horizontal Grinder, Caterpillar C-18 765 HP, Frame Hours 4,500.00, Caterpillar put in a new engine around 3,500 Hours, Dropped a Ring in the Engine, Has Platinum Engine Rebuilt, Undercarriage is 95%, Wireless Remote Control, Air Compressor, Ready for Work. Machine Weight: Approx. 68,100 lbs Width: 8' 2" Length: 40' 8" Height:11' 1" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2008 Peterson 5900 Tree Chipper -10560 hours -4000 on complete rebuild -Works as it should -Tires good -Two boxes of key knives

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

2003 Peterson HC5400 Grinder -7700 hours -New set of bananas, grates, and teeth -Has a wireless remote -Rotor recently balanced and serviced -New tires ands wheel bearings on axle -Comes with 25K worth of parts MACHINE RUNS AND WORKS BUT NEEDS A FEW MINOR REPAIRS -Has a hole in the metal plate that covers the rotor -Has a small leak in the fuel tank we currently use an auxiliary tank -Intermittent issue of conveyor not feeding. Believe it is a broken wire

The 2710D is Peterson’s most portable and efficient grinder. 3-Stage Grinding Process Provides Faster Reduction Peterson’s powerful up-turn 3-stage grinding process provides better fracturing of material and a more consistent product, giving you just the product your buyers are looking for The Impact Release System Protects Your Investment Peterson’s patented Impact Release System’s air bags provides uniform grinding and protection from contaminated feedstock, a feature unique to Peterson grinders. The 2710D is designed for operations requiring high production and frequent moves between jobs. At 68,100 pounds (30,900 kg), it is amongst the lightest of our grinder series. The 2710D is powerful, with your choice of a Caterpillar C15 Tier IV, 580 horsepower (433 kW) engine, or an optional C18 Tier II, 765 horse-power (570 kW) engine. Heavy duty and mobile, the 2710D can readily reduce a wide range of materials. The 2710D's large feed opening can reduce a wide range of materials. Measuring 60¾ x 32 inches (153 x 81 cm), when boosted by Peterson’s high lift feed roll, the feed opening’s maximum lift of 44 inches (112 cm), is amongst the largest in its class. The 2710D features a large grate area that enables it to produce materials to exact specifications. Our quick-change multiple grate system makes it easy to customize grate configurations to produce a wide variety of finished materials. Grates are removed through an easy-access door on the side wall. Machine Weight: Approx. 68,100 lbs Width: 8' 2" Length: 40' 8" Height:11' 1" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1998 PETERSON PACIFIC 2400A WOOD GRINDER CAT 3406C ENGINE GOOD MILL GOOD FEED CHAINS LOTS OF NEW PARTS RUNS VERY WELL WORK READY FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTH DEFERRED PAYMENTS WITH GOOD CREDIT IN-HOUSE FINANCING FOR MOST CREDIT TYPES GRANITEHE.COM

2002 Peterson 7400a Horizontal Grinder -End of summer 2022 we installed NEW -Cylinder packs and bearings -Both turbos -High pressure oil pump -Ecm -Injectors -All gaskets and orings -Oil pump -Twin disk clutch -Had the heads completely rebuilt -Radiator completely gone through -Rebuilt feed floor -Rebuilt mill -Mill bearings checked for clearance and passed -All belts and chains in good shape -Alot of extra screens and parts come with it. Some are brand new

Peterson 4800 Flail Debarker Wireless remote controlled Reman engine Runs and operates good

2019 Peterson 2710D Grinder -4550 hours -C18 CAT Engine764 HP -Motor replaced at 3500 Hours by CAT with Papers -Clean machine ready to work

Cat 3306 with recent engine work  (new head, liners etc) Remote control No stabilizers

New remote All outriggers intact and work. Two lower green wear plates worn but being replaced New radiator screen (pictured) will be installed.

Remote control

Monitor shows 5853 hours, serviced, ready to work

2020 Peterson 5710D -6,680 hours -C-27 CAT -Fresh service -New teeth -Undercarriage at 80% -Drag chains and discharge belt still like new PRICE HAS BEEN REDUCED to 437,000 USD !!!!!!! get it while it lasts!!!!!

2017 Peterson Pacific 4300 Whole Tree Chipper, Micro Chipper, New Rebuilt Cat C-18 Engine, 785 HP, Under 50 Hours, Frame Hours 10,500 Hours, Air Compressor on the machine, Ready to Chip Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2011 Peterson Pacific Horizontal Grinder Power Source: Diesel Engine Mfr: Cat Engine Model: C27 Horsepower: 1000 Has approximate 9050 hours

JUST REBUILT - CALL FOR DETAILS CAT C27 ORIGINAL HOURS - 1050 HP - TIER 3 NO DEF TOO MANY NEW PARTS TO NAME REBUILT TROUGH, NEW PT CLUTCH, NEW PUMPS (ALL), NEW WIRING HARNESS, NEW DRAG CHAIN, FEED BED, ALL HOSES, GRATES, COMPRESSOR AND MORE.

Machine recently had a New Crate Engine installed prior to fire and during the install the mill was completely reworked, rods,hammers, new wear plate, chains, chain head pulley This has sustained an engine fire which was contained in the engine compartment. Engine is not recoverable. This machine would be a great candidate for a Rebuild or an ideal Electric Conversation. A last resort would be to part out the machine.