Equipment For Sale

CANTEK - PCM 120, ...Hollow Chisel MortiserFeatures: -- Power stroke of head permits easy, fast, and accurate successive cuts. -- Separate fan blower to keep work clean and free from dust & chips. -- Manual adjustable table height and lateral position. -- Heavy-Duty cast iron construction. -- Convenient centralized control panel. -- Foot pedal actuated cycle. -- Pneumatic workpiece clamping by lever.Specifications: -- Chisel range: 1/4" - 3/4"; Motor; 2 HP; Spindle speed: 3,400 RPM. -- Table: 16-3/4" x 21-1/4; Table tilts 30°. -- Air pressure: 8kG Clamping; Cylinder: 2-1/2"; (63 mm). -- Head traveling cylinder: 3.15"; (80 mm); Table cross travel: 5";. -- Table longitudinal travel: 18";; Table vertical travel: 12";. -- Max. stock width: 12";; Max. mortising depth: 4";. -- Machine weight: 572 Lbs. -- Shipping weight: 726 Lbs; Shipping dimension: 35"; x 38"; x 70"; (880 x 960 x 1,780 mm).

CANTEK MX-370P EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): --Specifications:0.4 - 3 mm Edge thickness, panel thickness 0.315" - 1.77". Minimum panel length 6.7", minimum panel width 3-¾". Heated infeed fence for better glue adhesion. Fixed feed speed 29 FPM.Equipped with: -- Pre-mill (2) 1.5 kW each (12,000 RPM) counter-rotating cutter-heads for removing up to 3mm of the panel edge. -- Quick change 1.2 kg Teflon-coated glue pot is designed for EVA hot-melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than 1 minute. -- Guillotine shear: The guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consist of one large driven roller, followed by a smaller one. Workstations: -- End Trim: The end trim system is a single motor with (2) saw blades. The unit is mounted on high-precision linear guide rails. -- Top & bottom trimmers with (2) high-frequency motors for top & bottom trimming of the panel. Each motor has an inset knife cutter-head which can be adjusted from flush to beveled finish for thin edges, and radius trimming (2 mm radius). Single motor Corner Rounding Unit Can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm). The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Radius scraping unit fine-tunes the edge radius while removing knife marks during the milling process on radius edging. Insert knives have a 2 mm radius. -- Buffing unit leaves a super finish on ABS and PVC edging and removes any discoloration on the edges.

CANTEK TA-14 Tilting Arbor Table Saw. -- Heavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 7.5 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK SRS330 Straight Line Rip Saw;Features: -- Very Rigid machine body with a welded steel frame with an integral cast & machined table, which is fitted with a sturdy cast column & saw unit. -- Excellent precision work accuracy and durability. -- Absolute straight line feeding up to 13 ft. of ripping. -- Precision caterpillar chain and double "VEE" extra long (47.2";) guide rails are made of special cast iron the chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Holddown rolls (6 rows).Specifications: -- Max. work piece thickness 4.33". -- Min.work piece length 8". -- Distance between saw and column 18.1". -- Saw arbor dia. 1" and Saw blade dia. 10"; - 14". -- Saw arbor speed 4,300 RPM. -- Useable Chain Length 47";. -- Glue line guarantee 13’ (+/- 0.0098"; or 0.25 mm). -- Feed speeds variable 30 to 130 FPM. -- Arbor motor 20 HP -- Feed motor 2 HP -- Table size 36.6" x 64.6, Table height 31-7/8". Utilities: -- 230 V = 60.8 Full Load Amps. -- Electrics 460/3/60 = 30.4 Full Load Amps. -- Dust Collection Outlet 4"; -- Net weight 3,190 Lbs.Available Options: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03) -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)

CANTEK RAPIDEDGE PRO EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Pre-mill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counter rotating cutter-heads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot is designed for EVA hot melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with (2) pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consists of : (1) Large driven roller followed by a smaller one. Workstations: -- End Trim: (1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with (2) saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:The RAPID adjustment system uses a pneumatic 3-position adjustment to quickly change from 0.5 mm to 1 mm, to 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM high frequency motors for Top & Bottom trimming of the panel; each motor has an inset knife cutter head that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding:(1) 0.5 HP (0.37 kW) - 12,000 RPM, high frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm to 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile Scrappers:Multi-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat Scrappers:Flat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units:(2) 0.2 HP (0.12 kW) - 3,000 RPM motors, Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. -- Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Pre-milling Station so any overspray which gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface

Non-Oscillating Edge Sander with end sanding kit. -- 6" Wide x 108" long belt. -- 6" x 40" Graphite covered platen. -- 1 HP -1.5 HP, or 3 HP -2 HP, 3-Phase motor w/magnetic switch. -- 7" Diameter drive pulley. -- 7-3/4" x 37" Front table with a 6" vertical adjustment. -- End table for radius work with a 6" vertical adjustment. -- Heavy laminated tables, fabricated steel base and swing-away dust hood.

Cantek Double Surface Helical Planer

CANTEK JF-330A Profile Knife Grinder Clamping length of 12" (300mm) for both straight and profile grind; dia. of knife swing 12" (300mm). Grinding arbor: 3 HP grinding motor with VFD (LED Readout) drive from 1500 to 4200 RPM. Quick change removable (140mm) wheel adapter. Machine set for axial constant grinding and template set up on right hand side. Over the wheel precision diamond dresser assembly for dressing and dimensioning of wheel. Manual positioning: of grinding wheel to tool; positioning of back clearance angle and side clearance angle 5°/10°/15°. Quick change stylus turret for applications. (6) included with machine. Carriage: SCHNEEBERGER lineal bearing table movement. Table movement 12" x 6". Coolant system: 1/8 HP motor from coolant pump located in tank below. (3) coolant nozzles for smooth flow of coolant to knife rest during grinding. Additional hose with nozzle for cleanup. Stainless steel splash guards throughout!Option included: Motorized Side Clearance – including set left and set right Motorized Wheel Back Clearance Angle Motorized Grinding Wheel In/Out

CANTEK JF-330A Profile Knife Grinder Clamping length of 12" (300 mm) for both straight and profile grind; dia. of knife swing 12" (300 mm). -- Grinding Arbor: 3 HP grinding motor with VFD (LED Readout) drive from 1.500 to 4.200 RPM. Quick change removable (140 mm) wheel adapter. Machine set for axial constant grinding and template set up on right-hand side.Over the wheel precision diamond dresser assembly for dressing and dimensioning of wheel. Manual positioning: of grinding wheel to tool; positioning of back clearance angle and side clearance angle 5°/10° and 15°. Quick change stylus turret for applications; (6) included with machine. -- Carriage: SCHNEEBERGER linear bearing table movement. Table movement 12" x 6". -- Coolant system: 1/8 HP motor from coolant pump located in the tank below; (3) coolant nozzles for smooth flow of coolant to knife rest during grinding. Additional hose with nozzle for cleanup. Stainless steel splash guards throughout! -- Includes: Set up tools, coolant, HD worklight, grinding wheels and (1) arbor of choice - (1.25", 1.5", 40mm, 1-13/16", 2.125" or 50 mm).

CANTEK LBS300-5S 3-Sided Moulding Sander5-Head Brush Sander, 11" width and 4" height cap., for 3-sided sanding of linear profiled material. Head Configuration: -- (2) Sets of Top abrasive brushing heads with variable speed adjustment by inverter, 0.75 HP (0.55 kW) motor each. -- (1) Left side head, adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- (1) Right side sanding head which can be adjusted up/down and in/out, 0.5 HP (0.37 kW) motor. -- (1) Left side sanding head is adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- Brush head spindle speed adjustable from 200 - 1,200 RPM. -- Variable feed speed of 6.5 - 27 FPM, adjustment by frequency inverter.Features & Specifications: -- Min. workpiece length 26", min. workpiece thickness 3/8". -- 0.25 HP (0.18 kW) Conveyor motor, 0.33 HP (0.25 kW) moving brush head motor. -- Depending on the application, brushing heads can be cleaning brushes or abrasive cloth brushes. The dovetail pocket design allows for easy abrasive/brush replacement. -- Centralized control panel for operator convenience integrated into machine base.Also available in 460V, 3-Ph, 60 Cy (factory order only – app 10-12 weeks)

CANTEK - GT635ARD-16 25″ Double Surface Planer25″ Wide x 16″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external handwheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 16″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK - GT635ARD-8 25″ Double Surface Planer25″ Wide x 8″ thickness capacity Add on $2,500 for increase HP of top head to 30 HPFeatures: -- Cutterheads are spiral insert types with six (6) rows of carbide inserts. -- (2) Driven and (1) idle bedroll for superior feeding of even difficult material. -- Swiveling control panel for more ergonomic access to machine controls. -- Inverter variable speed control with feed speeds from 26 to 80 FPM. -- Easy to access external hand wheel adjustment of infeed bed. -- Hard chromed worktable for high wear resistance. -- Auto lubrication to conveyor chain, central lubrication for dovetail elevation guideways. -- Sectional chip breaker and sectional feed roller before top cutterhead.. -- Rubber outfeed top roller to prevent chip marking. -- Over thickness safety shut-off bar across infeed. -- Ammeter for each motor on the control panel to monitor motor load.Specifications: Maximum working width 25″Maximum working thickness 8″; Minimum thickness 0.394"; Min. workpiece length 12.2″Bottom head motor 20 HP, Top planing head motor 25 HP - Feed motor 5 HPTable elevation motor 1/2 HP.Cutterhead diameter 4", Knife dimensions 30 mm x 12 mm x 1.5 mm w/bevels (96 pcs per head)Cutterhead speed 5400 RPM;Feed speed (variable) 26 - 80 FPMDust ports 2 @ 6";; Table dimensions 27" x 103" (41.85" from the floor);Machine voltage 460/3/60 = 70 amps.Dims & Weight (LxWxH) 105″ x 45.1″ x 92.9″; (max.) Net weight 6700 Lbs,Packaging dimensions 109″ x 49″ x 89″; Gross weight 7800 Lbs

CANTEK MX340 EDGEBANDER (COMPACT): (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications: -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations: -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK GT610HI CARDAN SHAFT DRIVE DOUBLE SURFACE PLANERSpecifications: -- Max. working width 24" (610 mm). -- Max. working thickness 8" (200 mm). -- Min. working thickness 5/16″ (8 mm). -- Min. working length 12" (300 mm). -- Cutterhead RPM 5000 RPMCutterhead diameter 5.3" (135 mm). -- Feed speed 30-98 FPM 10 – 30 m/min. -- Top cutterhead motor 40 HP. -- Bottom cutterhead motor 30 HP. -- Feed motor 5 HP. -- Table Rolls 7 (3) driven. -- Opening hoist motor 1 HP. Machine dimensions: (LxWxH) 112"; x 67"; x 67"; 2830x1700x1700mm . Machine weight 8800 Lbs 4000 kgsShipping weight 9240 lbs 4200 kgs. -- Shipping dimensions (LxWxH) 115"; x 75"; x 75"; 2900 x 1900 x 1900mmMachine electrics (Standard) 460/3/60 = 110 amps (Other voltages on request, factory order)Key Advantages• Cast iron machine frame for superior vibration damping resulting in a long machine & bearing life.• Chrome-plated tables and top and bottom for maximum wear resistance.• Cutterheads are mounted in precision ABEC 7 RHP bearings.• The feed system uses a spring-loaded pin arrangement to pass material over the bottom jointing head.• Sectional serrated infeed roll before the top cutterhead.• Variable feed speed by frequency inverter (VFD) with digital display for the feed speed.• Digital thickness control for quickly and precisely setting the desired thickness.• The upper assembly is adjusted for desired thickness by four large-diameter cylindrical posts.• Adjustable infeed bed by easily accessible handwheel to set desired stock removal on the bottom head.• Easy to access swivel control panel with individual ammeters for load monitoring and hour meter to aid in maintenance planning.• Cutterhead starters are Y-Delta providing a soft start to the heads for reduced power consumption on startup.• Automatic lubrication to the conveyor feed system.• High-quality Schneider electrical components to CSA/UL standard.

CANTEK D405A 10' Sliding Table SawSpecifications: -- Max. cutting length 126". -- Max. depth of cut: 4.13" at 90° (355 mm), 5.12" at 90° (400 mm), 2.75" at 45° (355 mm). -- Main saw: 7-1/2 HP Motor, Blade dia. 16", Arbor dia. 30 mm (1.18"), Arbor tilt 0° - 45°, & Blade speeds 3,000, 4,000, & 5,000 RPM. -- Scoring saw: 1 HP - 8,000 RPM Motor, Blade dia. 120 mm (4.72"), & Arbor dia. 20 mm (0.79").Equipped with: -- 15-1/2"; x 126"; x 35-1/4"; H Precision anodized aluminum sliding table with Prismatic rollers running on precsion ground steel guides, 21.6"; x 35"; x 35.3"; H Cast-iron fixed table, 12.6"; x 32.7"; x 35.3"; H Auxiliary table. -- Main saw blade motorized height & tilt adjustment. -- 39-1/2"; L x 3-1/2"; H Aluminum rip fence, with 130 mm (51.18";) Cutting cap. -- Aluminum extruded crosscut fence, with (2) Flip stops with miter angle adjustment, & Sliding outrigger support. -- Eye-Level touchpad control, with LED Displays for main saw blade height & tilt. -- Overhead blade guard.

CANTEK D405A SLIDING TABLE SAWThe Cantek D405A Sliding Table Saw is the ideal sliding panel saw for high accuracy cutting of sheet materials to produce kitchen cabinetry, furniture, millwork operations, and more. This is our most industrial saw with a manual setting rip fence. The 10' sliding table is made from a precision aluminum extrusion and runs on precision linear guide rails. It has motorized rise/fall and tilt of the blades. Features: -- 126" Cutting length w/scoring; 126" x 15.5" Anodized sliding table that locks in any position for easy loading. -- Motorized Saw blade up or down movement by 1/4 HP electric servo motor; tilting by manual handle wheel. -- Scoring unit for clean, accurate chip-free cutting, ready for edge banding. Specifications: -- 7.5 HP Main saw motor; 45° tilting (30 mm) main saw arbor; 14" Main blade dia.; 3,000/4,000 & 5,000 RPM arbor speed. -- 5.3" Max. material thickness at 90°; 3.1" at 45°. -- 1 HP Scoring saw motor, 5" dia. scoring blade; 8,000 RPM. -- Equipped with: 49" Max. ripping cap.; micro-adjustable rip fence and extendable crosscut fence to 10' with (2) flip stops. -- Articulating overarm protection guard; outboard and rear extension tables. -- Includes: -- Saw Blade(s), Maintenance Tools, Operators' & Parts Manual and covered by (1) Year Warranty.

CANTEK - C14RS, ...Straight Line Rip SawSpecifications: --Overcutting Rip Saw. -- 4.92" Max. thickness cap; 8" min. length. -- Variable feed speeds from 49 to 128 FPM and powered by a 2 HP feed motor. -- 1-1/2" Dia. saw arbor powered by 15 HP arbor motor. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long. Equipped with & Features: -- (3) Rows of antikickback fingers: (2) Top & (1) Bottom, for safe operation. -- (8) Holddown rolls for increased control and precise straight line cutting (6 rows). -- 6" (150 mm) Wide chain track runs on double-V guide rails, which are made of special cast iron for added wear. -- Magnetic Controls.

CANTEK C-14RS Straight Line Rip Saw; Absolute straight line feeding Rip Saw. Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Excellent precision work accuracy and durability.Specifications: -- 4.92" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 20 HP arbor motor; swings 12" thru 16" dia. blade at 4,500 RPM; with 24" distance from blade to saw column. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long.Feed System & Chain: -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows). -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. When oil runs out the machine track stops running to avoid damage to track. Features: -- Precision Built Saw Arbor constructed of nickel chrome steel, large diameter, accurately ground and dynamically balanced. The arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V-Belt driven from below, with easy to access adjustments and controls. -- (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- Soft start - Star Delta starter. Telemecanique U/L magnetic starters.Options available at additional cost: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03)..................................... $ 495.00 -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)........... $ 118.00

CANTEK D405ANC 1-Axis SLIDING TABLE SAWSpecifications: -- 126" Cutting length w/scoring; 126" x 15.5" Anodized sliding table that locks in any position for easy loading. -- Motorized Saw blade up or down movement; motorized tilt with digital readout via 1/4 HP electric servo motor. Equipped with: -- 7.5 HP Main saw motor; 45° tilting (30 mm) main saw arbor; 14" Main blade dia.; 3,000/4,000 & 5,000 RPM arbor speed. -- 5.3" Max. material thickness at 90°; 3.1" at 45°. -- 1 HP Scoring saw motor; 20 mm arbor; 4.72" dia. scoring blade; 8,000 RPM. -- Features: -- Motorized rip fence control with eye level control; 51" Max. ripping cap.; crosscut miter fence to 10' with (2) flip stops. -- Articulating overarm protection guard; outboard and rear extension tables. -- Includes: -- Saw Blade(s), Maintenance Tools, Operators' & Parts Manual and covered by (1) Year Warranty.

CANTEK EM-12 End Matcher;1.6" to 12" Width x 0.4" to 1.38" thickness (to 2-1/4" optional) x 10.6" min. length capacity. Unlimited lengths possible.Specifications: -- Feed speeds to 295 FPM with approximate production speeds of 77 FPM (based on 6-1/2' incoming boards). -- Standard 173" long infeed table and standard 86" (2,200 mm) long outfeed table; -- (2) 10 HP cutterhead motors with 40 mm spindle diameters; 1 HP feed motor; 1/2 HP motor drive to cutterhead carriage; clamping pressure from top and side; 24 volt DC controls.Standard equipment and Features: -- Designed for machining tongue & groove with or without V's on flooring and panel products; designed to be used for finger joint cutting. -- Heavy-duty self supporting main frame; compact design requires minimum floor space.Feedworks: -- Capable of processing material as short as 11" to an unlimited length; variable speed through-feed systems is controlled by frequency inverter; through-feed system allows the tongue to be cut simultaneously on the tail of one board and the leading edge of the next board. -- Powered top Urethane rolls and spring loaded bed rollers feed the material into position for processing. -- Pneumatic side pressure ensures the material is held square against the fence.Complete with: -- Safety and noise reduction enclosure; convenient touch screen control is used to quickly activate and adjust the machine functions. -- Powered 176" long infeed conveyor is included (additional length optional); with a 86.6" long outfeed table (additional length optional). -- Includes: (2) Individual Precision Insert Tooling Heads as Supplied with Machine & stacked to make (1) pair of heads; set of heads provided for groove on left and tongue on right.