Equipment For Sale

MATTEI MNC 0055 Refrigerated Air Dryer (55 SCFM).MNC Series non-cycling dryers run continuously and control the refrigerant gas to maintain dew point keeping your air system free of water. Theyare the most cost effective method for applications where the ambient temperature remains above freezing.Features: -- Simple Microprocessor-based control provides dew point, temperature, functionality monitoring and time drain control. -- Equipped with: -- Removable cabinet for easy access to internal components; moisture dewpoint indicator and automatic condensate drain. -- Nominal Cap. based on 100° F ambient temperature; 100° F inlet temperature; 100°F, inlet pressure 100 PSIG. -- Max. Ambient temperature: 122°F°; Max. inlet temperature 158°F; min. ambient temperature 41°F (5°C); max. inlet pressure 203 PSIG (14 Bar G). -- Includes: Refrigerant: R134A; 3/4" NPRT-F Connection; .47 Kw.

MATTEI MNC 0110 Refrigerated Air Dryer (110 SCFM).MNC Series non-cycling dryers run continuously and control the refrigerant gas to maintain dew point keeping your air system free of water. Theyare the most cost effective method for applications where the ambient temperature remains above freezing.Features: -- Simple Microprocessor-based control provides dew point, temperature, functionality monitoring and time drain control. -- Equipped with: -- Removable cabinet for easy access to internal components; moisture dewpoint indicator and automatic condensate drain. -- Nominal Cap. based on 100° F ambient temperature; 100° F inlet temperature; 100°F, inlet pressure 100 PSIG. -- Max. Ambient temperature: 122°F°; Max. inlet temperature 158°F; min. ambient temperature 41°F (5°C); max. inlet pressure 203 PSIG (14 Bar G). -- Includes: Refrigerant: R134A; 1" NPRT-F Connection.

MATTEI ERC 1030L, 40 HP Rotary Vane Compressor (154 CFM @ 125 PSI)Features: -- No wear on compressor's moving mechanical parts; pulse-free air; low oil volume and consumption. -- Direct-coupled compressor and motor; slow 1,800 RPM; compact, quiet design - 81 dB (A) in an open-frame design.Equipped with: -- Bearingless air-ends - rotor stator unit (RSU) is the rotor which is simply supported by two (2) white metal Babbitt bushings that routinely deliver >100,000 hours of life. -- 40 HP ODP motor; 154 CFM @ 125 PSIG; air cooled aftercooler with 18°F approach temperature, 3-stage oil separator produces 3 ppm in compressed air. automatic drain valve; cleanable filter.Complete with: -- Efficient oil injection system guarantees a perfect holding among the moving parts, cooling and lubrication. An oil film on the stator's inside surface prevents the moving parts from wearing by avoiding a direct contact with the blades. -- Automatic load/no load, load matching modulation, automatic with modulation; 1" dia. air outlet.

MATTEI ERC 1018L, 25 HP Rotary Vane Compressor (105 CFM @ 125 PSI)Features: -- No wear on compressor's moving mechanical parts; pulse-free air; low oil volume and consumption. -- Direct-coupled compressor and motor; slow 1,800 RPM; compact, quiet design with 81 dB (A) in an open-frame design.Equipped with: -- Bearingless air-ends; rotor stator unit (RSU) is the rotor which is simply supported by (2) white metal Babbitt bushings that routinely deliver > 100,000 Hours of life. -- 25 HP ODP Motor; 105 CFM @ 125 PSIG; air cooled aftercooler with 18° F approach temperature'; 3-stage oil separator produces 3 PPM in compressed air, automatic drain valve; cleanable filter.Complete with: -- Efficient oil injection system guarantees a perfect holding among the moving parts, cooling, and lubrication. -- An oil film on the stator's inside surface prevents the moving parts from wearing by avoiding a direct contact with the blades. -- Automatic load/no load, load matching modulation; automatic with modulation; 1" dia. air outlet.

MATTISON 404 Straight Line Rip Saw;Specifications: --25 HP - 3,600 RPM Direct drive arbor motor; --14" dia. max. saw blade cap. (9" smallest dia.), --1-1/2" dia. arbor; 4" thickness capacity. -- Table size 65" x 77" long. -- 30" Distance from saw to left edge of table. -- 24-1/4" Between saw & column, and 24" rip distance to right of gauge. --Top roller holddown with 7-1/2" shortest stock handled under (1) roll, 15" under (2) rolls.Equipped with & Features: -- Overhead cutting design with single cast chain links. --Chain with automatic oil lubrication. -- 2 HP Feed motor with (4) feed speeds 62, 93, 124, & 186 FPM

Mattison 224 4 head moulder, 220 volts, 3 phase Call 800-459-2148 for more info.

Description Mattison "55-F" Turning Lathe - Back Knife 30" Cap. in length and 4" x 4" cap. dia. - Pneumatic feed; rear arbor with cutter-head driven by a 10 HP V-belt motor. Work piece rotation is belt driven by main motor with variable speed gear box, double end drive, mechanical feed of work piece into cutter head. Rear dust shroud with collection outlet.

MATTISON 69-42 MATTI-MAX Heavy Duty Automatic Rotary, high production Turning Lathe.Microprocessor controlled for quality turnings and ease of setup; 42" long turning cap. with rotating rear arbor, 4" x 4" max. and 3/4" x 3/4" min. stock size. -- Drives & Speeds: Equipped with: 20 HP - 2,700 RPM Cutterhead Drive, 2-5/8" dia. arbor with variable speed, 2 - 45 RPM stock-rotational speed via 1.5 HP DC drive (reversing) & self-contained hydraulic unit for precise feed control.. -- Complete With: Automatic hopper feed; MATTI-MAX microprocessor-based PLC controller with keypad entry; machine functions & operations parameters are set directly from the control; RPM of workpiece and feed rate can be programmed to vary during the cut. Matching the feed rate to the stock-rotational speed produces an efficient cut -- Features: MATTI-MAX also allows rough cutting at higher speeds (especially rounding of corners) and fine finish cutting at slower speeds. . Pneumatic tailstock with dual pressure to insure penetration of spur center at high pressure and can be adjusted lower for small dia. turnings. -- Total electrical load 27 Amps.

Madison 202 Straight Line Rip Saw

Mattison 404 Rip Saw Seller was using until they upgraded to a gang rip. Ready to ship.

The Rip Saw is still in good running condition and still in use.

Mattison 404 Straight Line Rip 230 Volt 3 Phase 25 HP Total 230/460 Dual Voltage on 20HP Mandrel Motor

MATTISON - 404, ...Straight Line Rip SawSpecifications: -- 15 HP - 3,600 RPM Direct drive arbor motor; 14" dia. max. saw blade cap. (9" smallest dia.), 1-1/2" dia. arbor; 4" thickness capacity. -- Table size: 65" x 77" long. -- 30" Distance from saw to left edge of table. -- 24-1/4" Between saw & column, and 24" rip distance to right of gauge. -- Top roller holddown with 7-1/2" shortest stock handled under (1) roll; 15" under (2) rolls.Equipped with & Features: -- Overhead cutting design with single cast chain links. -- Chain with automatic oil lubrication.. --4-Speed Feed: 62 - 93 - 124, & 186 FPM.

MATTISON - 202, ...Straight Line Rip SawSpecifications: -- 15 HP - 3,400 RPM Saw arbor motor, 9" - 14" max. blade capacity, 1-1/2" diameter arbor, overhead arbor design. -- 4" Max. depth of cut, 13" min. stock length, 24" max. rip capacity to the right of the blade, 77" x 65" table size.Equipped with & Features: --Overhead holddown with: (6) Pressure rollers, (3) front and (3) back; 2 HP feed drive, (4) feed speeds of 56 - 84 - 112 & 168 FPM (fixed at 25 FPM ).

MATTISON - 404, ...Straight Line Rip SawSpecifications: -- 20HP - 3,600 RPM Direct drive arbor motor; 14" dia. max. saw blade cap. (9" smallest dia.), 1-1/2" dia. arbor; 4" thickness capy. -- Table size: 65" x 77" Long. -- 30" Distance from saw to left edge of table. -- 24-1/4" Between saw & column and 24" rip distance to right of gauge. -- Top roller holddown with 7-1/2" shortest stock handled under (1) roll, 15" under (2) rolls.Equipped with & Features: -- Overhead cutting design with single cast chain links. -- Chain with automatic oil lubrication. -- 2 HP Feed motor with (2) feed speeds of 50 & 100 FPM. -- Laser light -- 480V to 240V Transformer -- Comes with some 12" 30 Tooth bladesNote : Seller claims the saw will give a glue line

Mattison 202 Straight Line Rip

MATTISON - 404, ...Straight Line Rip SawSpecifications: -- 15 HP - 3,600 RPM Direct drive arbor motor; 14" dia. max. saw blade cap. (9" smallest dia.), 1-1/2" dia. arbor; 4" thickness capacity. -- Table size of 65" x 77" long. -- 30" Distance from saw to left edge of table. -- 24-1/4" Between saw & column; 24" rip distance to right of gauge. -- Top roller holddown with 7-1/2" shortest stock handled under (1) roll; 15" under (2) rolls.Equipped with & Features: -- Overhead cutting design with single cast chain links. -- Chain with automatic oil lubrication. -- 2 HP Feed motor with (4) feed speeds. -- (2) Carbide rip blades.NOTE. Comes with a 208 Volt Transformer.

MAX - 36-SD, ...Double Disc SanderHeat treated and dynamically balanced 36" aluminum disc. -- Commercial duty; 5 HP motor base mounted with multiple drive belts. -- Heavy cast iron 16" x 46" table w/miter gauge slot. -- Easy precise tilting of the worktable with: 45° Forward &30° back. -- Rack & pinion adjustment of the table: Rise & fall; rack & pinion tilting of the table. -- Sanding station is mounted to (4) 3-1/2" heavy columns. -- Heavy bolt-down cast iron base.

Heat treated and dynamically balanced 36" aluminum disc. -- Commercial duty 5 HP motor base mounted with multiple drive belts. -- Heavy cast iron 16" x 46" table w/miter gauge slot. -- Easy precise tilting of the work table with 45° forward and 30° back. -- Rack and pinion adjustment of the table rise & fall and rack and pinion tilting of the table. -- Sanding station is mounted to (4) 3-1/2" heavy columns. -- Heavy bolt-down cast iron base. -- Optional: Motorized table elevation add.....$16, Motorized table elevation with limit switches add....., Electric brake add....., Circular attachment add....., Miter gauge add..... Hoist (chain drive lift for heavy parts) add..... JIL package (oil/dust proof switch components) add.. OPTIONS QUOTED UPON REQUEST.

Heat treated and dynamically balanced 18" aluminum disc. -- Commercial duty 1.5 HP direct drive motor. -- Heavy cast iron 10-1/2" x 24" table w/miter gauge slot. -- Easy precise tilting of the work table with 45° forward and 30° back. -- Rack and pinion adjustment of the table rise & fall and manual tilting of the table. -- Sanding station is mounted to a heavy column. -- Heavy bolt-down cast iron base. -- Optional: Upgrade to a 2 HP motor add.....$240, Miter gauge add.....$270, Rack and pinion movement of the tilt add....$400, Single Phase 1.5 HP motor add.....$120.