Equipment For Sale

Carolina Blower Dust Collector Dust Blower 19" Pipe 75HP Motor (Est)

Set of (3) Bins: (2) CAROTHERS-20 UNIT and (1) WEST COAST SHEET METAL- 15 UNIT with (2) Cyclones and One Hydraulic Power Pack...20 Unit CAROTHERS Shavings stores about 4,000 cu. ft. and 15 Unit Chip WCSM stores about 3,000 cu. ft. -- the (2) CAROTHERS Units share one 8' dia. Cyclone with levelling auger and the WCSM has separate 8' dia. Cyclone. Only (1) hydraulic Power pack is included. -- Rapid Powered Discharge Bin, prefabricated for nut & bolt erection, exterior constructed of 12-gauge structurally reinforced steel. -- Chips are discharged by a set of hydraulically operated clam-shell type bottom doors for approx. 78" x 144" free fall opening, opening & closing via (2) approx. 6.5" dia. double acting hydraulic cylinders w/stroke of approx. 48", Approx. 5 HP hydraulic pump motor with reservoir; braced, wide flange steel beam support structure with approx. 14' truck height clearance. -- Complete with: Operator's platform, upper catwalk w/handrail & (1) caged ladder and full w/ribbed sheet metal enclosure with truck size access door. -- Price for complete system includes dismantling and loading.

Carrier Vibrating Conveyor 67' x 38" Bottom x 18" sides x 18" Sides x 64" Across the Top, 50HP Motor with Drive.

24 wide x 24 long,

Carrier 28ft vibrating conveyor, 24" width, 4+" high, 5HP,

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Carthage Brunnette Machine 21" Ring Debarker 150' Per Minute put through.

CAS (COMPRESSED AIR SYSTEMS) B73H84-E Reciprocating Air CompressorElite Series 7.5 HP 80 Gallon Horizontal Compressor @ 175 PSI / 24 CFMFeatures & Specifications: -- Access to Compressor Valves without Compressor Head Removal. -- All UL Electrical Controls -- ASME Tested Powder Coated Steel Tank. -- Auto Start / Stop. -- Bearings on Both Ends of the Crank Shaft. -- Centrifugal Unloader. -- Disk and Spring Valves. -- Fully Enclosed Belt Guard. -- Heavy-Duty Air Filter. -- Heavy-Duty (2) Stage Solid Cast Iron Pump. -- Industrial Grade Electric Motor. -- Magnetic Starter Mounted and Wired. -- Needle Bearings, and Inserts on Rods. -- Stainless Steel Flex Air Lines. -- Swedish Steel Valves. -- TEFC Drive Motor (3 Phase Only). -- Torrington Needle Bearings. -- 2-Grove B Width Motor Pulley. -- 2-Piece Tank Top Plate Design.Elite Compressor Features: -- All Basic Features. -- Automatic Tank Drain. -- Belt Guard After Cooler. -- Low Oil Monitor. -- Tank Discharge Ball Valve. -- Vibration Pads.

CASADEI RANGER MC 3012 CNC MACHINING CENTER (VERTICAL, W/ATC): -- Specifications: Flexible "Vertical" Machining Center reaches movement speeds of 131 FPM (40 MPM) in X-axis, 98 FPM (30 MPM) in Y-axis, & 66 FPM (20 MPM) in Z-axis. -- Work Capacity:Max. part size for: X-Axis is 118" (3,000 mm); Y-axis 47.2" (1,200 mm); max. part thickness 3.9" (100 mm). -- Worktable:Vertical Phenolic MATRIX Grid table with: (5) Adjustable "tubeless" pneumatic locking panel supports, (3) adjustable vacuum pods per support.Pop Up Pneumatic backstops & pneumatic side stops for material positioning on the LH or RH side of the machine for mirror imaging. -- Boring Unit:(1) Boring block with: 2.25 HP (1.7 kW) - 4,000 RPM Motor.(10) Vertical spindles with: (5) Spindles in X-axis & (5) spindles in Y-axis.(6) Horizontal spindles with (2 + 2) in X-axis & (1 + 1) horizontal spindle in Y-axis.(1) X-Axis grooving saw: 5,000 RPM; for max. 120 mm dia. saw blade. -- Machining:(1) 6.7 HP (5 kW) Router with: ISO 30 Adaptor, variable speed from 1,000 - 18,000 RPM.(1) 5-Position ATC rack mounted on the side of the working unit. -- Operator & Machine Control:CNi PC Front End + Windows "XP" Operating System; 17" LCD, TFT monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; Ethernet connection.Real-time multitask processing; programs can be transferred via USB or downloading by wire is possible. -- Complete with:(1) 100 CBM/Hr BECKER Vacuum Pump; sound enclosure & perimeter safety devices. -- Actual Model is: CASADEI - RANGER MC 3012.

CASADEI ALA 23 EDGEBANDER WITH CORNER ROUNDING0.4 - 15 mm (1/2") Edge cap., panel thickness 10 to 60 mm (.39" to 2.36"). Minimum panel length 120 mm (4-3/4") and 55 mm (2-1/8") minimum width. Equipped with: -- Quick heat-up glue system,(approx. 12 Min) 1.5 Kg glue pot capacity. -- Pressure roll section with (3) rolls - one driven. Pneumatic cut-off guillotine.Workstations: -- Double end trim, chamfers 0° - 15° -- Top & bottom flush/radius trim, bevels 0° - 15°. -- Double motor Corner Rounding station -- Top & bottom scraping for 3 mm radius, -- Top & bottom buffing (0.25 HP - 2,800 RPM motors).NOTE: Seller states that the buffing unit appears to have an electrical issue and is not currently being used by the current owner";Actual Model: "ALA 23 R"

CASADEI FLEXA 47 RMA8 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- 0.4 mm - 3 mm Max. edge thickness cap., (0.5 mm to 3 mm for solid strip edge thickness). 8 mm - 50 mm (0.3" - 1.97") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 80 mm wide x 140 mm long (3.15" x 5.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Equipped with: -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 1 Kg. capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle.Workstations: -- Pre-milling unit with 3 HP - 8,300 RPM High Frequency motors. -- Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel is synchronized by the PLC control. -- Single motor, double-end trimming saw unit with (1) 0.25 HP - 12,000 RPM High Frequency motor. -- Top & Bottom Trim station with (2) 0.45 HP - 12,000 RPM High-Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutter-head position by mechanical digital readouts, quick release (electrical & mechanical). -- Includes (2) 3 mm radius cutters. -- Corner Rounding Unit: 2-Motor Corner Rounding unit for leading & trailing edges. -- Top & Bottom 3 mm scrape station -- Top & Bottom Buffing unit with (2) 0.20 HP - 1,400 RPM motors. -- Fixed feed speed 23 FPM. -- Actual Model is CASADEI FLEXA 47 RMA8

Panel height: 0.3 – 2.36” Coil edge thickness: .12” Strip edge thickness: .015 – .24” Max Overhang Total Top and Bottom: 0.16” Min panel width (min length of 8 ¼”: 3.54” Min panel length (min width of 3-15/16?): 5.5” Feed Speed: 33 f/min Glue Tank GP-200 Power: 2.4 kW Glue Capacity: 3.3 lbs End Trimming Unit IK/200 (each): .3 HP Cutting Speed: 12,000 RPM Blade Tilt: 0-15 deg. Top and Bottom Trimming TT/K Motor (each): .4 HP Cutting Speed: 12,000 RPM Shipping Footprint: 13' x 4' x 5' Weight: 2500 lbs Equipped With: – Pre-Milling Unit – Glue Applicator and Pressure Rollers – Edgebanding Trimming Guillotine – End Trim With 2 Tiltable Motors 0-15 deg. – Top and Bottom Trimming via 2 Motors – Profile/ Radius Scrape – Glue Scraping – Buffing

2016 Casadei Flexa 47 Edgebander 230 V/3 PH

Casadei R32 MK Pin Router

Case 621B Wheel Loader Believed to be a 1998 28,000 lb machine New transmission 2.5 yard bucket New lift cylinders Good 17.5-25 Yokohama tires Tight machine 2nd owner 7900 hours

Case 821, 3600hrs on Rebuilt Motor & Trans., Front Tires are 3yrs old, Runs Good

Case 321F 3000 hours Forks Bucket AC Heat Runs and operates great

The motor is rebilt with most parts Brand New and - 50 hr. Transmission in solid state. Hyd are tight. Tires are good. All in working order. CALL 270-291-1027

A clean machine in excellant condition. AC/Heat in the cab. The machine was not used hard. You have the bucket and the log forks. Call 440-313-8683

CASE W14 Wheel Loader with Bucket