Equipment For Sale

The Heavy-Duty Grapple is designed for up to 50 hp machines with a moderate work load. Made from 1/2" steel, it is strong yet light enough for smaller machines. Pivot-point grease fittings and couplers are standard.

This lightweight grapple is designed with small loaders in mind with limited lift capacity. Weighing only 454 lbs, it lets you grab a load without the fear of tipping your machine. Dual top clamps and grease fittings are standard.

The Blue Diamond Six-Way Dozer Blade is extremely rugged, easy to use, and offers superior visibility. It has a bolt-on-edge, skid shoes, heavy-duty cylinders, and comes with the electrical harness for your machine. Using a proven pivot system, it can tilt 10° and angle 30°. A blade extension is available for 8" of added height. Don't settle for anything less! Converts to snow plow by pulling two pins and adding height extension.

Blue Diamond Heavy Duty Forks

Blue Diamond Hydraulically Adjusting Forks

Blue Diamond Standard Forks

Blue Diamond Walk Through Forks

The Blue Diamond Tree Puller is an excellent tool for removing small trees and shrubs when the roots need pulled out. The 4 rows of serrated teeth lock onto the base of the tree, then pry or pull roots and all from the ground, shake the dirt out of the roots and carry to where you want to set your removed tree or shrub.

The Blue Diamond tree shear for skid steers will cut trees up to 12" in diameter with ease. The powerful 5" x 12" cylinder produces 29 tons of force at 2500 PSI. By simply pulling a pin, the shear will rotate 90 degrees, which is perfect for cutting limbs or fallen trees. This tree shear is designed to get the job done efficiently each and every time.

2022 Blue Diamond 72"" Skid Steer Brush Cutter - Severe Duty Open Front - 72” cutting width - 10"" Cutting Capacity - 4 double-sided blades - 200 CC Piston motor - 27-35 GPM Flow Range - 1” thick blade carrier with serrated edge - Visible pressure gauge to monitor workload - Bolt-on wear shoes to adjust height - Easy machine entry - 1 Year Warranty Call Quality Equipment & Parts for more information!

2022 Blue Diamond 72"" Skid Steer Brush Cutter - Extreme Duty Open Front - Versatility meets power and performance - Mows both grass as well as trees with ease - Purpose built 160CC hydraulic motor - Low flow / 16-26 GPM flow range - 3.5"" forged one piece drive spindle - 13"" x 1"" flange with 10 bolts connecting the blade carrier - 4 double-sided blades - 3/4"" thick blade carrier - 6"" diameter cutting capacity - Dual-direction cutting - No Case Drain required - Standard skid-steer coupler - 1 Year Warranty Call Quality Equipment & Parts for more information!

2022 Blue Diamond 78"" Root Grapple - Price includes hoses and fittings - Half inch, extra strong one-piece tines throughout - Closed in quick attach area - Reinforced top clamps - New “no pinch” hose routing - Opens to 34? - 35? deep - 8? tine spacing - 1.25? pivot pins in bushings with grease fittings Call Quality Equipment & Parts today for more information! (

BLUE GIANT SFSRH33/575 Scissor LiftHydraulic 3,000 Lbs. scissors lift -- 34" x 108" platform with idle roller -- Low 9" x high 53",Hydraulic pumping unit with 3 HP motor.

1999 Blum Mini Press

BM&M support hangers assemblies, Unused BM&M 773-11/36/4 screen support hangers with bolts still in factory box, photos show both sets of 4 each- (8 hangers available) s/n H177B4146A BM & M U-joint hanger modern style, BM &M screen hanger assembly, BM and M support u joint shafts, unused bmm screen hangers, BMM basket support hangers, stored in our warehouse for prompt delivery. We also have a few used hangers 36 inches long (measured yoke face to yoke face) available, 8 unused and 4 used hangers available ( photos of used hangers available upon request). We have them in inventory for prompt delivery.

MLS Number 12171481 BM&M 12X20 Chip Screen Rebuilt with new bottom pan Rebuilt motor and new belts Main bearing tested good Screen size buyer option

Boarke BKM-43K Wide Belt Sander

BOARKE 43 RK Wide Belt Sander, (2) Heads43" Width cap. Drum, Combination HeadHead Configuration1st Head: Contact Roll for Calibration 10"; Dia. Contact Roll, 85 Shore Hardness Dynamically balanced, 25 HP, 230/460 V, wired 230 V2nd Head: Combination Unit for Finish Sanding with ContactRoll, Pad or Both 5.5 “dia. Contact Roll 55 Shore Hardness, Dynamically balanced, 2.8"; wide Finishing Pad, 20 HP, 230 / 460 V, wired 230 V.Specifications: -- Sanding Units include: Photo electric belt tracking, Large diameter Tension, and Idle Rolls, Rigid Main beams for superior accuracy, 2.8"; Dia. spring loaded hold down rolls Quick release Tie Down Blocks, Y Delta Motor Starters -- Feed System: 4 ea. 5 ton capacity lifting screws, Heavy Duty 3-Ply conveyor belt, Heavy slider bed, machined for accuracy -- Variable conveyor speed from 7 – 45 FPM, Inverter Controlled Variable Speed, 2 HP drive motor, Conveyor belt centering device -- Infeed Roller, Guide Ways provide accurate vertical movement -- Control Panel (Located on Belt Loading Side for convenience) -- Digital Controller positions machine thickness -- Digital Readout in Inches or MM, And ν Buttons micro-adjust thickness in 0.001"; increments, Micro-Adjustment hand wheel for final thickness in 0.001"; increments -- Automatic Thickness Set Up, Motorized Thickness adjustment -- Amp Meter, and Volt MeterEquipped with & Features: -- Over Thickness Shut Off, Body activated safety switch at front of machine -- Door activated safety switches on ALL Doors, Emergency Stops front and rear -- UL / CE approved electrical components -- Disc Brakes on both motors -- Emergency Shut off activated when Air Pressure is too low, Overloads are tripped -- Emergency Stops are activated

37” Capacity single head 230 volt 3phase

Manufacturer’s Specification ( to be confirmed) - With its powerful 3 HP motor can delivers the performance professional demand. - Coupled with an industrial quality eccentric oscillation mechanism that delivers more efficient sanding, less tendency to burn and less belt loading. - Heavy duty spring system allows easy adjustment for the front aluminum table for full use of the abrasive surface. - Aluminum auxiliary contour table allow use of 4” idler roller as a drum sander. - 9” Dia. Drive drum, 4” Dia. Idler drum. - 9-1/2” x 48” cast iron platen with graphite pad. - Rugged bearing – assisted belt torsion devise.. - Aluminum table travels 8” and tilts – 5 to 45 degree. - Dual 4” dust ports. Belt speed: 4200 RPM - Sanding belt oscillate distance: 1/4” (6 mm) Motor5HP / 220V / 60Hz Belt Size230 x 3520mmn Frint Table Size (L x W)1210 x 300mm Dust Port 4”