Equipment For Sale

55 Ton Detachable Lowboy, 4th Axle Flip with Covered Fenders and Stobe Lights, 25' Well, 22" Loaded Deck Height, Load Bearing Covered Fenders, Air Ride Lift Rear w/Manual Override, 4 Position Ride Height, Battery Backup, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires Trailer without the Flip is $65,900 26' Well trailer also available for $67,500 Honda Power Unit adds $3,800.00 35 Ton and 51 Ton Trailers also available All prices plus F.E.T.

2014 Pitts LT-40-8L -102 wide -Tires good -Lights good -Brakes good

35 Ton Detach, 25' Well, Foldout Outriggers, Apitong Wood Floor, 22" Loaded Deck Height, Boom and Bucket Trough, Spring Suspension, Open Fender, 22.5 Tires, Battery Backup Strobe Lights Same trailer air ride, covered fenders $52,900.00 13hp Honda Power Unit add $3,800.00 51 Ton and 55 Ton Trailers also available Prices are plus FET

35 Ton Detach, 25' Well, 22" Deck Height, Air Ride W/Manual Override, 4 Position Ride Height, Foldout Outriggers, Load Bearing Covered Fenders, Battery Backup Strobe Lights, Apitong Wood Floor, 22.5 Tires, Boom and Bucket Trough Honda power unit add $3,800.00 Same trailer air ride with Spring BTR $57,300 Same Trailer air ride with Hydraulic BTR $60,900 Same trailer spring suspension, open fenders $48,900 51 Ton and 55 Ton Trailers also available Prices plus FET

35 Ton Detach Lowboy, 25' Well, 22" Deck Height, 3' Beavertail w/Hyd Ramps, Air Ride w/Manual Override, 4 Position Ride Height, Battery Backup Strobe Lights, Foldout Outriggers, Load Bearing Covered Wheels, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires BTR Spring Ramp $57,300 Spring Ride $48,900 Air Ride $52,900 Honda Power Unit $3800 Price plus FET

35 Ton Detach Lowboy, 25' Well, 22" Deck Height, 3' Beavertail w/Spring Ramps, Air Ride w/Manual Override, 4 Position Ride Height, Battery Backup Strobe Lights, Load Bearing Covered Wheels, Foldout Outriggers, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires 13HP Honda Power Unit adds $3,800. Same Spec Trailer with Hyd Ramps $60,900 51 and 55 Ton Trailers also available Prices are plus FET

Excellent condition-well maintained. All operates properly. 20’ well, read deck 8’6” flat space. Spring loaded ramps. 2-speed telescoping landings. Tie-down D-rings. 250/70R22.5 tires. Low boy well height 26” lower than most of this design made to fit most Skidders and Fellerbunchers and other 4 wheel equipment and be at or below 13’6” New 250/70R22.5 tires. New Brakes. All new rear LED lights.

35 Ton, Self Contained Hydraulic Ramps, 33" Deck Height, 8'6" Flat Deck, 27' Lower Deck, 4' Beavertail, Apitong Wood Floor, 17.5 Tires Same trailer with Spring Assisted Ramps $33,500 51 Ton Trailers also available Prices are plus FET

35 Ton Contractor Special Neck, Spring Assisted Ramps, 33" Deck Height, 8'6" Flat Upper Deck, 27' Lower Deck, 4' Beavertail, 17.5 Tires Same trailer with Self-Contained Hydraulic Ramps $37,500 51 Ton Trailers also available Prices are plus FET

60" CARRIAGE WITH MAST FOR SMALL WHEEL LOADER FUSION INTERFACE PJB LUMBER YARD FORKS SOLD AS IS TINES 1.5"X8"X48"

100" SIDE SHIFT MAST 48" TINES 60" WIDE CARRIAGE ISO LINKAGE PJB SMALL WHEEL LOADER LUMBER FORKS SOLD AS IS

100" MAST 48" TINES INSTALLED 60" WIDE CARRIAGE FOR CATERPILLAR ISO STYLE COUPLER PJB LUMBER YARD FORKS SOLD AS IS

FUSION COUPLER LUMBER YARD FORKS 100" SIDE SHIFT MAST FUSION TINES 1.5X8X48, CARRIAGE 60" WIDE

CONNECTING LINES INCLUDED FOR CATERPILLAR 926M PJB VOLVO STYLE QUICK COUPLER SOLD AS IS

18 CYD CAPACITY BOLT ON CUTTING EDGE PIN ON LUGGING PJB 982M WOOD CHIP BUCKET SOLD AS IS

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability