Equipment For Sale

Precision Husky 23 Chipper Needs engine Has Cummins KT19 650HP

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper dissc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though... The photo's show the optional extended shaft and hydraulic starting motor which is a special feature....

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

Precision vibrating conveyor, 18" wide pan x 30' long, 12" tall sides, BRAND NEW fiberglass paddles, excellent condition

Precision 4 Knife Grinder

New conveyor 20' length w/ drive

Precision vibrating conveyor, 18" wide pan x 55' long, 8" sides, electric drive, good working condition

15' of vibrating conveyor 24/33 x

2001 PRECISION HUSKY PROGRIND 1000 TUB GRINDER REDUCED 275 HP New Fixed Teeth New Auger Motors Good Tires Runs Well

Precision vibrating conveyor, 18" wide pan x 20' long, 10" tall sides, electric drive, good working condition

Precision vibrating conveyor, 18" wide pan x 27' long, 10" tall sides, electric drive, good working condition

Precision rosser head debarker, 36" capacity, electric drive on head, self-contained hyd unit for carriage etc., upgraded to chain drive for carriage, has flat barn sweep underneath, working condition

Precision 55 screener, was working when pulled out of production.

Precision 6 X 6 Chip Screen.

Includes 27' x 14" dia distribution auger, 3 each 35' x 12" dia loading augers, complete steel structure with columns and beams, control station without starters.

96" Precision 4K Left Hand Chipper w/ Andritz Turnknife System installed in good shape. Chipper had over $40,000 of parts installed less than year before removal.

96" PRECISION Chipper - Serial # C-3096. 1998 model, run only 7 months since new. 8 knife, 8" thick disk, bottom discharge. Out and ready to load. Motor available

Husky Brute XL335 Log Loader joysticks delimber hyd hookup for bucksaw fresh paint runs and operates great owned for 12 years priced without bucksaw but saw is also available

Precision Husky Brute XL 335 Log Loader Self Propelled Levers

Precision Disc Scalping Screen Model PDS648 48” wide x approx 8’ long 6 shafts and the discs are stitch welded on