Equipment For Sale

This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

John Deere 1010E Forwarder Tracks and Tires Veriga tracks at 90% Used approximately 800 hours Three Nokian Forest Rider 650-45-24.5 tires at 80% mounted on rims and one rim

2012 Vermeer TR626 Wildcat Trommel Screen with 12,500 hours. Weight: 47,500 lbs Width: 102 in (8 ft 6 in) Height: 13 ft 4 in Length: 49 ft Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2017 Vermeer Tr626 Trommel Screen -2600 hours -Tipping grid -3/8 stainless steel screen mesh Turnkey unit!!!

2020 Vermeer BC1800 XL Chipper, Machine has 2000 Hours, One Owner, Hydraulic Winch, Autofeed System, 173 HP 6 Cylinder Turbo Engine, DEF Engine, Well Maintained Machine Ready for Work. Length: 177” Height: 110” Width: 80” Weight 9,270 lb Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2019 Vermeer TR-5300 Trommel Screen, 2,200 Hours on Engine, New Sprockets and New Drive Chains, In excellent condition. Ready for Work. Weight 32,000 lbs Width (transport): 8.2 ft Length (transport): 39 ft Height (transport): 13.4 ft Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2013 Vermeer TR626 Wildcat Trommel Screen with 13,000 hours. Recently had all frame work redone – details can be provided. Weight: 47,500 lbs Width: 102 in (8 ft 6 in) Height: 13 ft 4 in Length: 49 ft Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

Hours-1,677 Serial Number- 1VRC312H8K1001097 Low-hour late model grinder That was used for regrind. The machine is very clean and straight for age and hours. Machine Has Full Factory Warranty Remaining Delivery is available at the buyer’s expense

2001 Vermeer TG400AL Tub Grinder, Cat 3406 Diesel Engine 3,600 Original Hours, New Duplex Mill, New Hydraulic Pump Conveyor. Heat and AC in the Enclosed Cab, Cylinders have been rebuilt, Ready to Grind. Transport Length: 33.5 ft Transport Width: 9.2 ft Transport Height: 10.5 ft Weight: 25,000 lbs Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2006 Vermeer TG9000 13’ Tub Grinder, Cat 3412E 860hp with 8900 hours, Heads and rebuilt done at 6500 hours. Width 46 ft Width 11.9 ft Height 165 in Weight 106,000 lb Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2018 Vermeer HG2800 Cat C27 950HP Has Cat Engine Warranty to 6,000 Hours or Approx. 10-31-22 Approx 2600 Hours

2017 Vermeer HG6000 Horizontal Grinder -4,400 hours -C-18 -Belts good -No blowby Turn Key Unit

2009 Vermeer HG 6000TX Track Horizontal Grinder, with 10,341hours on a Cat C-18, 630HP Engine. $150k worth of repairs less then 300hours ago. Strong running, good machine. Receipts and list of new parts available for serious buyers only. New Infeed conveyor, chain, and roller New idler roller bearing New infeed wear strips New hammer feed drive belts New anvil bars New shear edge and cutters New mill seat new tail belt New roller lock cylinder and more Weight: 75,000 lbs Transport length: Maximum of 37.3 ft Transport width: Maximum of 9.2 ft Transport height: Maximum of 148 in Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2006 Vermeer TG7000 2100 hours Work ready

2014 Vermeer 2300XL Whole Tree Drum Chipper, C13 Cat 440HP with 4474 hours, Infeed, Remote, Woods Ready. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2022 Vermeer WC2500TX -300 hours -Tier4f Cummins 600H.P -Microchip and Macro chip Drums available -Dual infeed conveyor Turn key unit !!!!!

2015 Vermeer DCR Style Mulcher, New Teeth, Ready to Work Please Call For More Info!

Vermeer HG365 Grinder New infeed roll and remote control Ready to go to work!

2013 Vermeer HG6000 -6000 hours -CAT C-18 engine -New material output belt that comes with it -Tires and lights good