Gang Rip Saws For Sale

LHI AUTOMATIC RAKE FEEDER with the following equipment: -- Panel Feeder with up to 18' Long x 5' Wide x 1" Thick Sheet Capacity (with 4' min. sheet length) -- Feeder loads from right side when viewed from the End of the Scissors Lift -- Auto-cycle for Rake Feeder -- 6' Line-Up conveyor with Fence & Powered Pinch Wheel -- 8000 Lbs. Tandem Scissors Lift with 5' x 17' top, 600-Volt, 3-phase, 2 HP motor -- 5-Section Gravity Rollers on Scissors Lifts -- 12' Powered 5 Strand Chain Conveyor Feeds Tilt Lift w/forward/ reverse, jog controls -- Wired for 600-Volt/3-Phase/60-Cycle Operation (other voltages available) -- Arranged for Customer Provided MultiScore Panel Ripper with right side arbor loading

Rip Saw Model SDL 1200 Edging Conveyor Model UHY 1900

This system was purchased used and never put into service.

Madison 202 Straight Line Rip Saw

Mattison 404 Rip Saw Seller was using until they upgraded to a gang rip. Ready to ship.

The Rip Saw is still in good running condition and still in use.

MATTISON - 404, ...Straight Line Rip SawSpecifications: approx.20HP - 3,600 RPM Direct drive arbor motor; 14" dia. max. saw blade cap. (9" smallest dia.), 1-1/2" dia. arbor; 4" thickness capy. -- Table size: 65" x 77" Long. -- 30" Distance from saw to left edge of table. -- 24-1/4" Between saw & column and 24" rip distance to right of gauge. -- Top roller holddown with 7-1/2" shortest stock handled under (1) roll, 15" under (2) rolls.Equipped with & Features: -- Overhead cutting design with single cast chain links. -- Chain with automatic oil lubrication. -- 2 HP Feed motor with (2) feed speeds of 50 & 100 FPM

Mereen Johnson 424DC 24" Wide Arbor 75 HP Motor (460v/3Ph) 3 HP Feed Speed Variable Feed Speed Air loaded pressure rollers

Mereen Johnson 424 DC Gang Rip Outfeed Rollers

Mereen Johnson 424 DC/SR4 Gang Rip Saw with Automated Infeed with multiple lasers manufacturer’s specs to be confirmed 24” width capacity 3-1/2” thickness capacity 75 HP main motor 3 hp feed motor feed rete 30-245 fpm

These two rip saws were removed from service in working condition some time ago. The seller purchased them and never installed them. They have been in storage the whole time.

Mereen Johnson Gang Rip Saw Model 431-DC s/n MJ-5132

MEREEN-JOHNSON 424 DC GANG RIP SAW 24 inch width capacity 75 HP arbor motor- 3600 RPM direct drive 5 HP variable speed feed ( new belt ) Four ( 4 ) kick-back finger sets : ( Two ( 2 ) top in-feed, One ( 1 ) bottom in-feed, One ( 1 ) top out-feed ) A new out-board arbor bearing assembly New set of alum bars and rubber slats installed It is wired 480 volts 3 phase . The serial no. is MJ-4709 One saw sleeve and set of spacers ( 6 saw blades ) Cleaned, painted, and checked.

Mereen Johnson 431 DC

MEREEN-JOHNSON 312 DC DIP CHAIN GANG RIPSAW:Specifications: -- 1 Moving Blade, -- Hydraulic pinch roller infeed.: -- 12" Arbor cap., 14" max. dia. tooling, -- 3-1/2" max. thickness, -- 30" min. length for glue joint accuracy & 22" min. for busting only; 6" throat.Equipped with:& Features -- 50 HP - 3,600 RPM TEFC Direct drive motor, arbor -- Disc brake & load meter, arbor lockout on the access door. -- Feed & chain: 3 HP Variable feed speed from 30 - 150 FPM with adjustable jam protection, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain, "Quad Life" hardened dip cams, -- Extruded structural aluminum feed bed slats with replaceable steel-backed rubber insert strips, -- Automatic chain oiler with low-level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls; full width segmented maple -- Spring-loaded overhead pressure shoe, -- Pressure rolls & pressure shoe unit adjust with scale & pointer thickness reference; -- Anti-kickback fingers. -- (1) saw sleeve and spacerIncludes-- Blades, Sleeves, Spacers

Mereen Johnson Gang rip saw

Mereen-Johnson 424 Gang Rip sawSpecifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max. manual thickness adjustment, -- 14" min. length for glue joint accuracy and 22" min. for busting only, -- 6" throat. Equipped with and Features -- 75 HP - 3,600 RPM TEFC Direct drive motor, -- 2-3/16" dia. arbor with disc brake, -- load meter and slip-off outboard bearing. -- Feed & chain: 3 HP Variable feed speed 30 to 170 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain -- "Quad Life" hardened dip cams -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips --, Automatic chain oiler. -- (4) 3" Dia. air loaded overhead pressure rolls; full width spring loaded overhead bed plate, -- Pressure rolls and bed plate unit with scale & pointer thickness reference; -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- Sound enclosure, -- (2) Upper dust hoods (1) 10" & (1) 5" dia. and (1) lower 4" dia. hood, -- Requires 3,820 CFM;Also included: -- (7) laser with mounting rack -- (2) additional arbor and lots of spacers

1999 Mereen-Johnson Gang Rip Saw | Model 431

Mereen-Johnson 312-DC/SR2 Gang Rip Saw with Rip Navigator Scout InfeedSpecifications -- Arbor Space: 12" -- Thickness Capacity: Up to 3" (w/ 14" Blades) -- Minimum Length: 22" (30" for Glue-Joint) -- Two Shifting Blades -- 1"Minimum Net Rip Between Shifting Blades -- Machine-Mounted Laser Stand -- Arbor Motor: 50 HP, Direct-Drive -- Feed Motor: 3 HP -- Variable Speed Feed: 30 - 150 FPM -- "Posi-Feed" Friction Feed Chain w/ Aluminum Slats and Replaceable Rubber Inserts (Rubber Inserts are Brand New) -- Hardened Steel Feed Chains & Track w/ Oil Mist Lubrication -- Air-Loaded Press Rolls -- Single Lower, Double Upper Infeed Anti-Kickback Fingers w/ Single Upper OutfeedEquipped with & Features -- Rip Navigator Scout Arranged to Receive 17'-6" Maximum Length Boards from Scissors Lift Manually placed on Board Dealer ArmsIndividual Boards are Automatically Dealt onto Lateral Chains and Conveyed to a Board Stop -- Board Stop Queues Boards for Advancement to Disappearing Fence -- Automatic Adjusting Fence Positions Boards for Placement into Gang Rip Saw Fence Positioning Through Rip Navigator -- Fence Mounted Pinch Roll Feeds -- Board to Gang Rip Saw Mounted Power Table -- Voltage: 480 with Transformer (Original Voltage as built is 575) -- New Bearing in Saw Arbor -- New Rails for Scout Infeed Chains -- 5743 HOURS -- NEW IN 2013

MEREEN-JOHNSON Model 524-DDCSR 2+4 Double Arbor Gang Rip SawSPECIFICATIONS: -- First Arbor Arranged with Two (2) Independently Adjustable Select Saw Assemblies for Mounting Hogging Blades -- Second Arbor with Four (4) Independently Adjustable Select Saw Assemblies -- Arbor Space 24" -- Thickness Capacity to 1-3/4" with 12" Tooling and 2-3/4" Using 14" Tooling -- Minimum Length 30"Equipped with & Features -- Two (2) M-J Direct Drive Motors 75 HP Each -- Feed Motor 7.5 HP TEFC, 30' to 235' rate with Frequency Inverter Speed Control -- Saw Set Up for Second Party Optimizing System.