Gang Rip Saws For Sale

Raimann KM310 Rip Saw Weinig Quick-Fix System

Raimann KR450M Gang Rip Saw with Infeed Cutting width: 450 mm Main Motor: 50 HP Feed speed: 8-80 M/Min Value Rip 4+ Infeed System

ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

Salvamac Salvapush 2000-4100 Optimizing/Defect Saw Max. board length: 4100 mm (13.45 ft) Min. board length 500 mm (1.64 ft) min. board thickness 12 mm Blade : 500mm (20”). Cutting capacity: Min. 30x12 mm (1.18’x0.51’), Max. 270x120 mm (10.62”x4.72”) / 300x95 mm (11.81”x3.74”) 240v/480v 3 phase with transformer • Feeding by precision toothed belt width 50 mm. 33 strips of hard system • Outfeed table 3 mt (9.84 ft) • Position reading with brushless motor encoder with digital Ethercat connection • Infeed motor pushing 120Kg/ 264lb • Max speed push feed system 90m/min – 296ft/min • Hydraulic rising of the pusher at the end of the cutting cycle and overhead returning • During pusher carriage return; photocell wood mapping determines board length • 25° tilted working table • Guards, cables, interlocks, etc. to EC safety standards

ZHW800-70- SMW Gang Rip Saw - Saw from 3/8"-2 3/4"T x 31 1/2"W, 11"dia Saw Blade, 1-10 Blades, 29hp Motor. Also Available: ZHW800-80- SMW Gang Rip Saw - Saw from 3/8"-3 1/4"T x 31 1/2"W, 12"dia Saw Blade, 1-10 Blades, 40hp Motor. ZHW800-100- SMW Gang Rip Saw - Saw from 3/4"-4"T x 31 1/2"W, 14"dia Saw Blade, 1-10 Blades, 49hp Motor.

SMW Multi Blade Rip Saw

Sawmill World Mdl SH500-50 Gang Rip Saw with 2 X 20inch Material Capacity

SCMI Gang Rip Saw S/N B.540480

Shurman Double Arbor Gang Saw 12" Capacity Thin Kerf Babbit Grinder

Smithway XL gang rip saw model 104Specifications -- 12" Max. width cap., 10 HP bottom mount motor, arbor direct drive; roll feed works, (1) set top rolls on infeed and (1) set top on the outfeed, 0.5 HP feed, fixed feed speed at approx. 30 to 40 FPM.From the seller ---Photo shows saw blade cover removed for photo

It is a 2 saw re-rip with one moveable saw and an adjustable fence. Capacities: Minimum length = 8” Maximum length = 192” Minimum width = 1 ½” Maximum width = 6” Minimum thickness = 7/8” Maximum thickness = 1”

Gang Rip Set Up as a 2 saw with 15HP Electric Motor

Unknown Splitter Saw. Up to 6" thick. Hydraulic Driven Rollers. #00845

Multirip circular saw for block cutting, with reinforced structure and high production speed. Trailed top and bottom rollers, upper rollers with adjustment, shafts with cartridge system for quicker and more efficient replacement of the set of saws, U-beam base with levelers and central lubrication. It does not come with the circular saws. - Maximum inlet width: 600 mm; - Minimum inlet height: 70 mm; - Maximum inlet height: 160 mm; - Double arbor: Ø 80 mm; - Number of saws per axle: 10x; - Exterior saws Ø: 350 mm interior saws - Ø: 110 mm; - Upper press rollers: 2x; - Bottom rollers: 6x; - Max. Feed speed: 35 m L / min for logs - 160mm above in diameter; - Max. Feed speed: 40-50 m L / min - only for logs 130-160mm in diameter; - Lower main motor indicated: 200 hp 2p (1x) Included; - Top main motor indicated: 150 hp - Main motor belt: 4 / 3v (8 Pcs); - Motor traction of the rollers: 5 cv 4p; - Gearmotor: GS (crown and pinion); - Length: 3366 mm; - Width: 2782 mm; - Height: 2233 mm; - Approximate weight: 5.470 kg

WEINIG - VALU-RIP: Infeed Conveyor System for Rip Saw Specifications -- 7-Chain Deck; spaced at: 0", 25", 54", 75", 96", 120", 147". -- (5) Board stops on Chain Deck. -- Roller Deck with: (7) Drop chains. -- (8) 50" Rollers; powered by: 2 HP Motor. -- Drop Chains spaced at: 0", 36", 54", 72", 110", 147", 181-1/2". -- Automatic Saw Fence with: TISFOON Scanning System. -- Powered Pinch Roll before Saw: 2 HP Motor.NOTE: This is part of a Total Plant Liquidation; please call for details!

WEINIG RAIMAN PROFIRIP 450M And Combiscan EVO Luxscan Lumber Scanner SystemThe system is complete with: -- (1) Weinig lateral lumber feeder table to scanner head -- 12" wide rubber belted infeed -- Roller/Sweep type lateral conveyor with sequencing and buffer to scanner infeed -- (1) Weinig CombiScan EVO Luxscan Line Feed through lumber scanner -- Model CombiScan EVO -- Max width 310 mm (12.2") -- Min width 25 mm (0.984") -- Max length 6500 mm (255.9") Min length 900 mm (35.4") -- Max thickness 100 mm (3.93") -- Min thickness 12 mm (0.472") -- Speed range 80 to 300 m/Min (up to 250 boards/min) -- Max throughput 200 m/Min -- Luxscan combiscan EVo R with two cameras, top-bottom (2 side detection laser cameras, 2 side detection color defect high-resolution cameras, 2 side detection with dot laser, 2 side line scatter, angle crack detection 2 side) -- Freestanding operator computer control station -- Flat screen color display with keyboard -- Opticore direct controls -- Freestanding electrical and computer control cabinet -- Freestanding chiller unit for laser system -- Scanner infeed and outfeed table system -- Safety guards with access doors around the scanner and rip line machines -- Includes the machine operators' manuals -- (1) Weinig sweep type lateral conveyor table from scanner to the rip sequencer table -- Chain deck type sequencing and spacing conveyor table -- Infeed rip saw board flipper with servo fence system to rip saw -- (1) Weinig Raimann ProfiRip 450M Gang Rip Saw With (2) Movable blade -- 51 kW, 460 V, three-phase, 60 Hz -- Max cutting width 450 mm (17.7") -- Max cutting height (with 450 mm diameter blade and without pressure board) 150 mm (5.9") -- Max cutting height (with 450 mm diameter blade and with pressure board) 135 mm (5.31") -- Min. cutting thickness: 15 mm (0.59") -- Min cutting length 780 mm (30.7") -- Chain width 470 mm (18.5") -- Diameter of saw arbor 65 mm (2.55") -- Min blade diameter 300 mm (11.8") -- Max blade diameter 450 mm (17.7") -- Saw blade bore 80 mm (3.14") -- Arbor speed 3900 RPM -- Feed speed range: 15 to 120 m/Min -- Machine weight 4500 Kg (9920 Lbs) -- Saw drive motor 45 kW, 460 volt three phase -- Feed motor 4 kW, 460 V, three-phase -- (1) Fixed and (2) movable saw blade design -- Edging removal system -- Sound and safety machine enclosure -- Front access door with inspection window and safety interlock -- Freestanding operator computer control station -- Pro-Face color touch screen display -- Joystick movable blade controls -- Freestanding electrical control cabinet -- Includes the machine operator's manuals -- (1) Weinig rip saw outfeed table with lateral feeder to chop saw station -- Outfeed roller/sweep type conveyor -- Cross conveyor table with servo accelerator -- Freestanding operator conveyor system controls (zone ripping)Note: System installed new in 2019 and sells for a fraction of new.