Equipment For Sale

Verville 4 Stage Bagging System. #C921 Located in WI.

VERVILLE VP300 3-Station Bagging SystemSpecifications: -- Main motor: 25 HP -- High of Tubes 116" -- Bag Size 11" x 17" x Up to 30" Finish HighNote: Bin and Infeed auger/conveyor is not included.

VERVILLE 6-SCREW HOLDING BINSpecifications: -- (6) Motorized 14-1/2" Diameter Bottom Screw -- (1) Motorized 14-1/2" Diameter Exit Screw -- 11 Feet Long -- 16 Feet Wide -- 18 Feet High -- 12 Feet High Support LegsDismantled and Loaded on Truck

VESTIL EHLT-2464-2-55 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 2,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 24" x 64". -- Lowered height 7", raised height 55". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VESTIL EHLT-4896-4-56 Scissor Lift Full featured electric hydraulic scissor lift tables are used by all types of manufacturing and warehouse facilities.Safety features: -- Electric toe guard to protect pinch points during lowering of the table. -- Internal safety velocity fuse to maintain platform height in event of hose or fitting failure. -- Maintenance prop, and upper travel limit switch to stop table at maximum height. Specifications: -- 4,000 Lbs. lifting capacity. -- 2 HP totally enclosed electric motor. -- Platform size 48" x 96". -- Lowered height 8", raised height 56". -- 24V AC push button hand control. -- Hydraulic component rating of 3,000 PSI.

VICKERS - 60 HP, ...Hydraulic Power PackHydraulic Power Pack with all the bells and whistles: VICKERS Pump & valves and a SENTINEL tank. Hydraulic Power Pack Includes -- Variable volume, pressure compensated, piston pump. -- Capacity: 8 Cu. in./rev. -- Pressure rating: 4,000 PSI. -- Driver: 60 HP Electric motor; 1,750 RPM. -- Reservoir: 200 Gal. -- Kidney Loop: Gear pump w/filter. -- Air-cooled Heat Exchanger. -- Return line filter. -- Liquid lever switch and temperature switch. -- Fluid inspection window.NOTE: This item was installed earlier but never used. Year of manufacturing is approximate.

VIET - S1 211, ...2-Head Wide Belt SanderWidth Cap. 43"; Drum and Combination Head.2-Head with: (1) Contact Roller and (1) Fine Sanding Platen; 1,100 mm (43") working width. Solid wood, veneer & lacquer Sander.Head Configuration:1st Head: Rubber covered contact roll, spirally grooved, dia. 200 mm (7.9").2nd Head: Fine sanding platen, segmented, electronically controlled.Specifications: --Both heads driven by (1) main motor 15 kW (20 HP). -- Both heads equipped with: 1,130 x 2,620 mm (44-1/2" x 103") abrasive belts. -- Roller shoe holddowns, Pneumatic tension of sanding belts and feed conveyor. Feed System: -- Vacuum conveyor system for small and lacquered parts. -- Variable speed conveyor belt drive from 3 - 16 MPM (11 - 52 FPM). -- Part thickness 3 - 160 mm (1.2" - 6.3"). -- Motorized part thickness adjustment, with digital height readout. Equipped with & Features: -- SCS Control panel with storage capacity for multiple sanding programs. -- Load meter on main motor. -- Disc brake on main motor. -- Emergency stops front & back. -- Roller table extensions front & back.

VIET - S2-321-HP/KRT, ...3-Head Planer Sander3-Head Planer/Sander 43" with: Planer, Drum and Combi-HeadSpecifications: -- Max. operating width: 1,100 mm (43") -- Min/Max thickness: 3 mm - 160 mm (1/8" to 6.3") -- Working Height: 900 mm (36") -- Abrasive Belt dimension: 44" x 103" -- Feed speed: 3 - 16 MPM (9-3/4 - 52 FPM) -- Rubberized drum: 30 HP Motor -- Combination head with drum & platen; driven by the same motor as the sanding drum -- Extended infeed & outfeed roller -- Planer head with helical insert knives: 30 HP Drive motor

Viet Opera 5-4.3 RRRR, (4) Head Wide Belt SanderCalibrating Sander (89 Hours)53″ wide cap. - Drum, Drum, Drum, DrumHead Configuration1st Head: 9″ Helical grooved steel drum powered by a 22 kW or 29.5 HP motor.2nd Head: VARIABLE SPEED (via VFD) 9″ helical grooved rubber drum powered by a 18.5 kW or 25 HP motor. 3rd Head: VARIABLE SPEED (via VFD) 11″ helical grooved rubber drum powered by a 15 kW or 20 HP motor. 4th Head: VARIABLE SPEED (via VFD) 11″ helical grooved rubber drum powered by a 15 kW or 20 HP motor.5th Station: Dust brush powered by a 1.27 kW or 1.7 HP motorSpecifications -- The durometer does get softer from head 2 to 3 and then from head 3 to 4. -- It has 53″ width capacity and a 200 mm or 7.87″ thickness capacity. -- Right above the machine's infeed, you will find inspection LED lighting, a digital thickness calibration unit, and a wireless Mitutoyo Digimatic Caliper that communicates with the Opera’s operating system. -- The vacuum bed is powered by an 11 kW or 15 HP blower under the sander to save space. -- The feed mat is powered by a 5.5 kW or 7.5 HP motor with variable speed via a VFD with feed speeds from 9.8 to 52.4 FPM.Equipped with & Features -- Inside you will find interior LED lighting while all the controls on this Opera are upfront via a touch screen -- Constant pass lineNOTE : This calibrating sander has a total of 1,982 power on hours and ONLY 89 run (conveyor) hours. This is a very loaded, LOW Viet Viet Opera 5 (4) Head 53″ Calibrating Sander

VIET - S211 R+ KRT, 2-Head Wide Belt Sander43" Width. cap.: Drum and Combination head.Head Configuration:1st Head: 160 mm 6.3″ Helical grooved rubber drum. 25 HP motor2nd Head: 160 mm(6.3") Helical grooved rubber drum with a platen combination head., 25 HP motorSpecifications: -- Each heads are powered by 25 HP motor. -- The heads can be programmed to pneumatically raise & lower along with the platen and do (3) sanding combinations (with the twist of a button). -- Digital height readout along with a calibration unit to the left side of the conveyor. -- Conveyor speed is controlled via a variable frequency drive 2.5 HP . --Max width: 43″. -- Max. height: 6-1/4". -- Variable speed conveyor belt drive from: 3 - 16 MPM (11 - 52 FPM).Equipped with & Features: -- Both heads equipped with: 1,130 x 1900 mm (44-1/2" x 75"). -- Roller & pressure shoe holddowns. -- Pneumatic tension of sanding belts and feed conveyor. -- Load meter on main motor. -- Disc brake on main motor. -- Emergency stops front & back. -- Roller table extensions front & back.. NOTE: This is an extremely low hour 2016 BIESSE Viet S1 dual head 43″ calibrating Wide Belt Sander.

VIET Challenge S2-3232620-SW53 Wide Belt Sander, 3-Head with (3) Contact Rollers3-Head, 1,350 mm (53") max. working width. Solid wood and thick veneer sander. Head configuration:1st Head: Rubber covered contact roll 320 mm (12-1/2") diameter. Shore hardness 80, 18.5 KW motor, abrasive belt speed 24 m/Sec. (79 FPS).2nd Head: Rubber covered contact roll 200 mm (7.9") diameter. Shore hardness 50. 15KW motor. Abrasive belt speed 20 m/Sec. (66 FPS).3rd Head: Rubber covered contact roll 200 mm (7.9") diameter. Shore hardness 30. 14 m/Sec (46 FPS). (2nd motor 15 KW drives 2nd & 3rd headSpecifications: --All heads equipped with 1380 x 2620 mm (54 " x 103") abrasive belts; roller & pressure shoe hold downs. -- Feed system: Vacuum conveyor system. 3 KW (4 HP) motor variable speed belt drive from 3 - 16 m/Min (11 - 52 FPM). -- Material thickness range 3 - 160 mm (0.1 - 6.3"). -- Pneumatic feed conveyor tension; constant pass-line with height adjustment (for varying material thickness) with digital read-out, driven by 0.75 HP (0.55 KW) motor for the upper section. -- Machine control system: PLC processor control with sequential motor startup and storage for multiple sanding programs.Equipped with & Features: --Panel cleaning followed by turbo-jet air jets at exit side; belt cleaning by air blasts. -- Load meters on all heads. Dust extraction for each head [email protected]" diameter and [email protected]"; disc brakes on all heads; emergency stop for belt breaks. CE Compliant.Note: Comes with 2 extra rollsActual model is VIET S2-3232620-SW53 Wide Belt Sander

VIET Planer Sander Sander model S2 321 HR/KRT ( 2018 ) !st head planer with helical insert cutter knives 30 HP 460 volts 2nd head drum contact roller 3rd head combination drum rollers with finish platen Both sanding heads run by 30 HP motor 460 volts Adjustable rubber coated pressure rollers Opening capacity range 1/8” to 6” Sanding belt size 44” x 103” Feed speed 19 to 52 FPM Electronic digital readout with auto thickness positioning Disc brakes on each machining station Front and rear emergency push buttons Electro pneumatic sanding belt tracking This machine has low hours as owner only ran half days first year and less after next years

VIET OPERA 7-5.3 HRKXF 1,350 mm (53.15") 5-Head Knife Planer/Calibrating Sander, with 3,634 Powered-On & 675 Run Hrs.Specifications: -- Thickness cap. 200 mm (7.87";).Equipped with: -- 1st Head: “HPG"; Planer Unit, with 180 mm (7.09";) Dia. Cutterhead with (520) Knives & 30 kW (40 HP) Motor, 26-Section Front pressure shoe, & Single back pressure shoe with chromium anti-wear lip. -- 2nd Head: “2620"; Working Unit, with 320 mm (12.60";) Dia. 90 Shore Rubber-covered contact roll with 22 kW (30 HP) Motor, Cam shaft system belt cleaning blower, & Single front pressure shoe with chromium anti-wear lip. -- 3rd Head: “KOMBI 2620"; Combination Working Unit, with 190 mm (7.48";) Dia. 60 Shore Rubber-covered contact roll, Platen with “IPA"; Electronic segmented pad with (42) Segments, 32 mm (1.26";) Pitch, Low pressure action, & Contact insert with Steel & felt grooves & Removable graphite cloth, 18.5 kW (25 HP) Motor with Electronic inverter, & Cam shaft system belt cleaning blower. -- 4th Head: “X-SPIN PLUS"; Unit, with (15) Discs, with Steel inserts & Slots for 180 grit abrasive inserts, & 11 kW (15 HP) Motor with Electronic inverter. -- 4th Head: “2620"; Superfinishing Unit, with 2,160 x 1,420 mm (85.04"; x 55.91";) Chevron belt with Removable graphite cloth, & Platen with “IPA"; Electronic segmented pad with (42) Segments, 32 mm (1.26";) Pitch, Low pressure action, & Contact insert with Steel & felt grooves & Removable graphite cloth, 15 kW (20 HP) Motor with Electronic inverter, & Cam shaft system belt cleaning blower. -- All heads with Disc brakes. -- Adjustable 55 Shore spiral grooved rubber-coated pressure rollers. -- 200 mm (7.87";) Dia. “SCOTCH-BRITE"; Brush roll, with 1.1 kW (1-1/2 HP) Motor. -- Rotary Panel cleaner, with Air saving system. -- 50 Shore Rubber ground laminar surface vacuum feed belt, with 900 mm (35.43";) Height, 7.5 kW (10 HP) Motor with Electronic inverter, & Pneumatic belt tracking. -- 3-Roll Front & rear table extensions, Each with (1) Driven & (2) Idler Rollers. -- All motors with IP54 & Thermal relay protections. -- Self-lubrication system for pneumatic components. -- Front safety bar. -- Carbon steel electro-welded profile frame. -- IPC 15"; Touchscreen control (“SOPHIA"; IoT Connection-ready), with 100-Working program memory, Motor load meters, & Electronic digital readout with Automatic thickness positioning.Complete with: -- Translucent “LEXAN"; Side doors. -- 150 mm (5.91";) Wireless Panel Thickness Caliper.

Viking Sentinel Pallet Nailing Machine S/N 1052 Model M700 480 3Phase

2000 | 480V | 72" x 60" | Left/Left

480V | 72" x 60"

1997 Viking Champion QC306 | 480V

440/480v | 1994

2001 | Viking Turbo 505 | Left, Left

2018 Viking Express 403 | 2 Branders | 4 Nailing Heads | 60x72 Capacity