Equipment For Sale

35 Ton Lowboy, 33" Deck Height, 27' Flat Deck, 4' Beavertail, Spring Assisted Ramps, 17.5 Tires, Apitong Wood Floor Same spec Trailer with Self Contained Hydraulic Ramps $35,900 Prices are plus FET

2020 PITTS LB35-33 Hydraulic Ramps, 504'L, 102""W, 4 Spring Suspension, Steel, 235/17.5 hub pilot Tires, Tandem Axle, Apitong Floor, 35 Ton, Self Contained Hydraulic Ramps, 33"" Loaded Deck Height, 27' Flat Deck, 4' Beavertail, 17.5 Tires, Apitong Wood Floor, Same trailer with Spring assisted Ramps $31,900 Prices are plus FET

Header, 6 bolsters

1999 Pitts 40’ Log Trailer, Center Point Suspension, Rebuilt

35 Ton, Self Contained Hydraulic Ramps, 33" Deck Height, 8'6" Flat Deck, 27' Lower Deck, 4' Beavertail, Apitong Wood Floor, 17.5 Tires Same trailer with Spring Assisted Ramps $33,500 51 Ton Trailers also available Prices are plus FET

55 Ton Detachable Lowboy, 4th Axle Flip with Covered Fenders and Stobe Lights, 25' Well, 22" Loaded Deck Height, Load Bearing Covered Fenders, Air Ride Lift Rear w/Manual Override, 4 Position Ride Height, Battery Backup, Apitong Wood Floor, Boom and Bucket Trough, 22.5 Tires Trailer without the Flip is $65,900 26' Well trailer also available for $67,500 Honda Power Unit adds $3,800.00 35 Ton and 51 Ton Trailers also available All prices plus F.E.T.

35 Ton, Contractor Special Neck, Self Contained Hydraulic Ramps, 27' Flat Deck, 4' Beavertail, 38" Deck Height, Apitong Wood Floor, 22.5 Tires Same trailer with 22.5 tires, 38" deck height, and Spring Ramps available for $32,500 Same trailer with 17.5 tires and 33" deck height available for $37,500 Prices are plus FET

25 Ton Contractor Special Neck, 33" Deck Height, Spring Ramps and Beavertail, 44'x102", 26' Flat Load Deck, Full Deck Apitong Floor, 17.5 Tires Prices are plus FET

Log trailer -Bushings worn -lights work -225 tires on it -Single point suspension -102" wide

Pitts Pup Trailer Used for 6 months Good rubber Adjustable bunks Like new

Straight Frame Log Trailer, 42', Air Ride Lift Front, 6 Bolster all Welded, 3 Dead Bolsters Centered Between each bunk, Lumber Gussets, Micro Lights in all Bolsters, 11R24.5 Hub Pilot, Grapple Bar, Covered Tandem, Headboard, Digital Riteweigh Scales All Prices are plus FET LMI is your go to source for semi-truck trailers located in Waverly, Tennessee! We have been family owned and operated since 1980. We are North America’s largest stocking dealer of lowboy trailers. We are proud to be ranked #1 in New Trailer Sales for Pitts Trailers since 2009, Dorsey’s Top Dealer since 2015, Jet’s largest detach dealer, and Landoll’s Top 3 Dealer since 2019. Our inventory also includes new and used forestry, scrap, and material handling equipment and trailers, and we’re proud to be an authorized dealer for Barko, Robotec, CSI, and Demco. We also carry parts for the equipment lines we carry. Give us a call today and we will get your parts shipped out quickly. Need your purchase moved? We have a network of over the road trucks to get your trailer to you ASAP! Need your purchase financed? We offer financing options to fit your needs. We accept and welcome used trade-in trailers, as well as purchase used trailers. Our location stocks and install on-demand the following: toolboxes, ramp kits, chains, binders, straps, bungees, bulkheads, headache racks, tarps, sliding tarp systems, aluminum wheels, new and used tires, everything you would need for your flatbed, drop deck or lowboy. Check out our inventory online. If you don’t find what you’re looking for, contact us and we’ll help you track it down. We look forward to serving you!

60" CARRIAGE WITH MAST FOR SMALL WHEEL LOADER FUSION INTERFACE PJB LUMBER YARD FORKS SOLD AS IS TINES 1.5"X8"X48"

18 CYD CAPACITY BOLT ON CUTTING EDGE PIN ON LUGGING PJB 982M WOOD CHIP BUCKET SOLD AS IS

FUSION COUPLER LUMBER YARD FORKS 100" SIDE SHIFT MAST FUSION TINES 1.5X8X48, CARRIAGE 60" WIDE

Complete Player Design Drying System - (2) Touch Screen Controllers - (1) PLC Control Box - (1) 12’ X 20’ Burner – 25 million BTU capacity with tempered sight glass that can run green chips/dust - (1) Burner Auger , Gearbox, and Motor - (1) Burner Blower Fan Assembly and Motor - (1) Player Single Pass Insulated Dryer Drum (12x50), 8” T section track, 28” Trunnions, Drive lubrication system, Sprocket, Chain and Gearbox / Motor (Drum rated for output material volume of 16,000 lbs per hour) - (1) Air Pro 48” Overhung Fan Assembly (ID Fan) (No Motor) ---- (Part# 12113601, Type-IERS615, Serial# 21136,) - (1) 200 HP motor for ID Fan - (1) Beck- Damper Adjustment Arm/Gearbox (ID fan comes with opposed blade inlet damper with a 300 ft-lb Beck actuator and armature) ---- (Model 11-209-155212-04-01---- 120V 1PH / 110VA ) - Piping and dampers for piping - Missing approximately 20’ of Dryer Drum Discharge piping - Missing approximately 20’ of Dryer Drum Recycle piping - System was rated at approx 9.25 Tons/hour

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

Pneumafil Baghouse Model 115-816, 8'Bags, 125HP on Blower with 34" inlet and 30' x 35" outlet.

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter

Pneumafil Dust Collector Model 135 (13.5-460-8): 150 hp. The round duct enters the collector at 48" Diameter. Dixie Air Dust Collector: Size: 108-12, Type: SPB, 50 HP, Inlet to the motor, circumference is 90".