Equipment For Sale

QUICK 20" Wide Conveyorized Glue Applicator -- 20" wide grooved rubber glue applicator roll with stainless steel doctor blade and glue reservoir. -- Features easy adjustment or removal of doctor blade, 16' overall length, 8' infeed before the glue roller and 8' outfeed conveyor. -- Equipped with: Heavy Duty 0.25 HP motor drive for slat-type conveyor and glue roll, limit switch with wand for automatically stopping the slat bed conveyor when stock reaches the Clamp Carrier, adjustable safety slip clutch. -- Complete with: Foot levelers, Heavy Duty crossbars, chain guard, high quality anti-stick urethane finish, and owner & operator's manuals.

QUICK 30-Section HEAVY DUTY Pneumatic Clamp Carrier with 8-1/2' width cap. -- (6) Heavy Duty zinc plated clamps per section for (180) total clamps, 38" opening on clamp. -- Jaw sizes on clamps are 3-1/2" high x 4-3/4" wide with 1° inward draft.Equipped with: -- Pneumatic overhead panel flattener, -- Pneumatic clamp tightener, -- Electric motor rotation with indexing.Standard features include: -- Foot levelers, coiled air lines where used, and flexible conduit for wires.

Quick Clamp Carrier Model: SA-CCFP-10.5-14 10.5' Wide 14 Section Clamp: 2.5" high jaw, 38" opening Pneumatic clamp tightener Pneumatic Panel Flattener Electric Drive

Quick Clamp Rack 12' Wide Clamp: 3.5" wide, 40" opening

QUICK MACHINERY N-P80 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 49" x 97" with end loading on 49" side. -- 80 PSI Platen pressure over the entire surface area with 102 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (28) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 49" X 97" . -- The press model shown in pictures is a dual platen powered feed through end load press. -- Actual model is N-P80-04-08-EL-1PL-M-40-R-1Z

QUICK MACHINERY N-P80 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with end loading on 62" side. -- 80 PSI Platen pressure over the entire surface area with 105 PSI supply air pressure. Pressure is applied by (60) 12.8" dia. air pods with 5.9" stroke; -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 62" X 146". (2) Air pressure zones for upper platen: (4' x 8' and 5' x 12') -- Optional powered roller tracks for an additional fee. -- The press model shown in pictures is a dual platen powered feed through end load press. -- Actual model is N-P80-05-12-EL-1PL-M-40-2Z

QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side (also available as end loading). -- 50 PSI Platen pressure over the entire surface area with 90 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- (2) Pressure air pressure zones: 5' x 12' and 4' x 8'. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of idle conveyor roller tracks by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.

QUICK MACHINERY N-P50 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with side loading on 146" side. -- 50 PSI Platen pressure over the entire surface area with 93 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; (36) air pods total for this size press. -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired.Actual Model is a N-P50-05-12-SL-1PL-M-40-R-1Z.• Maximum platen pressure: 50 PSI at 93 PSI supply pressure• Lower platen dimensions: 5' x 12'• Side-loading design• Number of upper platens: 1• Upper platen dimensions: 5' x 12'• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 36• Number of air pressure zones: 1 (5' x 12' pressing)Optional powered roller tracks are available. -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK L-HLPP-2-20-43-8-12 ...2-Sided Hydraulic Laminating Press: -- Number of working sections: (2) -- Working width, section #1: 6" and 8" -- Working width, section #2: 8", 10"; and 12" -- Maximum working length: 6,200mm (20.3') -- Maximum working height: 1,100mm (43.3") -- Pressure at the glue line: Up to 175 PSIMain Laminating Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 100 mm dia. x 80 mm strokeHolddown Cylinders: -- Number of cylinders, section #1: (14) -- Number of cylinders, section #2: (21) -- Size of cylinders: 40 mm dia. x 150 mm strokeLift Cylinders: -- Number of cylinders: (2) on each side = (4) -- Size of cylinders: 63 mm dia.Hydraulic Pump: -- Drive motor: 10 HP -- Maximum pressure: 140 kG/cm² -- Maximum Holddown Cylinder Pressure: 50 kG/cm² -- Maximum Side Lift Cylinder Pressure: 50 kG/cm² -- Shipped without hydraulic oil in the oil tank

QUICK MACHINERY N-P80 Air Pod style Cold Press -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface. -- Specifications: -- Platen pressing area size: 38" x 98"; with end loading on 37" side. -- 80 PSI Platen pressure over the entire surface area with 105 PSI supply air pressure. Pressure is applied by 12.8" dia. air pods with 5.9" stroke; -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 1" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 38" X 98". -- Optional: powered roller tracksSpecifications:QUICK Laminating Pod PressN-P80-03-08-EL-1PL-M-40-R-1Z• Maximum platen pressure: 81 psi at 90 psi supply pressure• Lower platen dimensions: 3' x 8' (38" x 98")• End-loading or Side-loading: End-loading• Number of upper platens: 1• Upper platen(s) dimensions: 3' x 8' (38" x 98")• Vertical opening: Motorized adjustable from 2" to 40"• Lower platen roller tracks: Yes, Non-powered roller tracks• Number of 12.8" diameter, 5.9" stroke air pods: 24• Number of air pressure zones: 1 -- The press model shown in pictures is a dual platen powered feed through end-load press.

QUICK N-P50 Fixed Daylight Opening Air Pod PressThis Pod Press can produce a maximum 50 PSI platen pressure over the entire surface at 100 PSI supply air pressure. Press has a fixed vertical daylight opening of 44". The (18) 12.8" max. diameter air pods have 5.9" stroke.Material conveyance is via automatically extending and retracting (via pneumatic cylinders) non-powered roller tracks. A cycle timer provides visual and audible signals at the end of each cycle if desired, and also automatically releases platen air pressure at the end of each cycle, if desired.Specifications: -- Maximum platen pressure: 50 PSI at 100 PSI supply pressure. -- Lower platen dimensions: 4' x 8' -- End-loading or Side-loading: End-loading -- Number of upper platens: 1 -- Upper platen(s) dimensions: 4' x 8' -- Vertical opening: Fixed at 44" -- Lower platen Non-powered roller tracks. -- (18) 12.8" diameter, 5.9" stroke air pods. -- Number of air pressure zones: 1Lead Time: Approximately (12) weeks from time of order.Actual Model: N-P50-04-08-EL-1PL-F-44-R-1ZNOTE: Please let us know of any "Special or Specific" safety equipment requirements that you may have prior to order

QUICK MODEL L-HLPP-1-36-43-6 SINGLE SIDED HYDRAULIC LAMINATING PRESS FOR POSTS AND BEAMS: -- Number of working sections: 1 -- Maximum working length: 36'. The 36' length achieved by manufacturing the machines in two 18' long pieces; the two 18' pieces are then joined together, resulting in 36' total working length. -- Maximum working width: 43" -- Maximum working thickness: 6"Main Laminating Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 80mm dia. x 80mm strokeHolddown Cylinders: -- Number of cylinders: (30) -- Size of cylinders: 40mm dia. x 150mm strokeSide Lift Cylinders: -- Number of cylinders: (2) per section = (4) -- Size of cylinders: 63mm dia.Hydraulics: -- Hydraulic pump drive motor: 7-1/2 HP -- Maximum pressure: 140kg/cm2 -- Maximum Holddown Cylinder Pressure: 50kg/cm2 -- Maximum Side Lift Cylinder Pressure: 50kg/cm2 -- NOTE: Shipped without hydraulic oil

QUICK Clamp Rack 8' -- Description: The QUICK Clamp Rack features a cleanly-designed, exceptionally strong frame, with massive 4" x 4" structural tubing cross beams and feet, and 4" x 6" structural tubing legs.The innovative “two-sided"; frame design allows for either one-sided or two-sided operation, at the shop owner’s discretion. The one-sided configuration allows for placement of the frame tightly against a wall, for maximum compactness. The two-sided configuration doubles the amount of easily-accessible clamping area, for industry-leading “room to work."; The Rack is configured by choosing either of the two available foot mounting positions. -- Specifications:96" Wide (36) Clamps 3.5" X 40" opening

Quickwood RO 1300 Sander

QUICKWOOD CD2-300 Moulding & Profile Sander or Denibber;4-Head Brush Loading Sander, 12" width and 4" height cap., for 3-sided sanding & denibbing. Head Configuration: -- (2) "BH300" Overhead rotating abrasive/brush heads, both arbors equipped with a combination of abrasive and brush loadings, 12" long arbors, 12" max. dia. sanding discs. -- 0.75 HP Motor drives each arbor with inverter for 200 - 1,200 RPM arbor rotation speed. -- Right & Left ("BH-140" & "BH-100" respectively) side mounted rotating abrasive/brush heads. -- Tilting heads and adjustable in-and-out, 6" long arbor, 8" dia. sanding discs, 0.5 HP motor each head. -- 0" - 4" Max. manual part height adjustment via hand wheel; 57-1/2" long roller conveyor with PVC covered rollers, variable feed speed 10 - 60 FPM. -- Infeed & outfeed overhead holddown rolls and (1) between the top heads. Includes centralized control panel, hubs, abrasive, & brush. -- Can also be ordered with just (2) top heads or (3) heads, ie. Left or Right. Call for separate prices.

Quickwood Pro 1100 Sander

8 or more brushes arranged at 360 ° with respect to the work pieces Adjustable inclination for the profile step QRC module for the super finishing of the flat parts in view

Quickwood Pro 1600 Sander

100hp Quincy Northwest QNW-V-100-F rotary screw air compressor Rogers 500 CFM air compressor Model: QNW-V-100-F Both compressors are photographed in the photo gallery Serial #1-- 060116 and #2-- 060117 Air end: model FSS204102, serial# NA064325, P/N 144220-001 Date: 4/25/2006 Motor: Toshiba 100hp, 460 volts, Two identical compressors are available Prior use was inside of a building Contact us for price and a freight rate. Can provide test run video

Quincy screw compressor, Model; QSI245ANA31A, Serial #; 94877, 100 hp electric power, 69,848 hrs, good working condition