Equipment For Sale

BOERE - TKS 900, ...2-Head Top Wide Belt Sanding Machine900 mm (36") Working width; equipped with: (1) Contact roller, (1) Fine sanding pad. Head Configuration -- 1st Head: Rubber contact roller, spirally grooved, Shore hardness 80, diameter 265 mm (10.4"), driven by 18 kW (25 HP) motor. -- 2nd Head: Sanding pad, electronic-pneumatic controlled, 114.7 kW (20 HP); Air blowing unit for cleaning the abrasive belt. -- All heads use abrasive belts size: 910 x 1,900 mm (35.8" x 74.8").Feed System -- Variable feed speed: From 5 - 25 MPM (16 - 82 FPM); 1.5 kW (2 HP) motor. -- Motorized part thickness opening: 3 - 150 mm (0.1" - 6"), driven by 0.12 kW (0,15 HP) motor.Complete with: -- Emergency Stop Systems for abrasive belt breakage and low belt tension. -- Infeed safety bar for operator protection and oversized parts. -- Automatic Star Delta starters, motor load meters. -- Pneumatic belt tension. -- Emergency Stops at the front & back. -- Extended infeed belt, approx. 42" long.Actual model: BOERE "TKS 900".

BOERE TPK-900 Planer Sander 2 Heads -- 2-Head, 900 mm (36") width cap. equipped with (1) Knife planer head and (1) Rubberized Drum. -- 1st Head: Helical knife planer head with (4) spirals of 4-sided carbide inserts each 14 mm x 14 mm, 20 HP motor. -- 2nd Head: Drum, approx 10" dia. rubber covered contact roll, 15 HP motor; all heads with air operated caliper type disc brakes. -- Variable feed speed 13 - 52 FPM, 2.5 HP motor, automatic conveyor belt tracking, anti-kick back fingers on infeed, infeed hold down shoes and double outfeed pinch rolls on outfeed. -- Motorized part thickness adjustment 0" - 6" with LED read out display . Complete with: -- Controls mounted on belt loading side, load meters for each head, conveyor infeed extension.

Boge compressors S-100 100HP S/N 50475

Model: C 30 N PSI150 3.210 m3/min CFM: 113 30 HP Size: 30.4 x 41.6 x 68.3 Weight: 1193 lbs

Boilersmith Boiler System Installed But Never Run

Biomass Boilersmith Boiler 400hp 250 psi. barely used, 90 percent life expectancy All inclusive,boiler, Biomass unit, ash conveyors, all input/ feed conveyors, EPA approved pollution mitigation system, Electrical components. Was designed to have a Co-Gen unit added

Wood-Fired BOILERSMITH Boiler fitted with CHALLENGER Cumbustion Unit;Complete with the following major components and features: -- 250 PSIG design pressure. -- BOILERSMITH Boiler Model HRT2H8-2600SF-XW-250 with 2600 Sq. Ft. boiler surface area. -- Fuel can vary in moisture up to 50%. (Boiler HP is reduced as moisture increases.) -- Fuel feed Auger with Variable Frequency Drive. -- Fire-Tube Boiler with integrated Air Blast Tube Cleaning. -- De-Ash Augers. -- All Electrical Controls and starters. -- All mechanical/ electircal engineer's drawings.NOTES: &#9679 Removed and ready to load onto two trucks, 38,000 and 42,000 pounds. &#9679 15,000 to 16,000 pounds per hour steam if burning wood pellets. &#9679 No building included but same building can be purchased from STAR.

BolDesign Kiln that includes Future-Design Controls FDC-2010-K5C Small Kiln Features • Board Feet Capacity: 2,000 to 10,000 BF (Board Feet) • Expect a 6-9 Week Turn Around • Easy to Clean and Maintain • Built with Aluminum and Stainless Steel, The Same Aluminum that is food grade used in Commercial Kitchens • RH control results in less lumber damage, this leaves you with better, brighter colors These Kilns are Built for Forklifts • Pallet Stock Drying Kiln; Disassembled crated and ready to load. 1 truck

BOLLEGRAAF - HBC-80, ...Horizontal Auto-Tie Baler with ConveyorSpecifications: -- Bale size: 43" x 51" x 29" -- Motor: 60 HP -- Conveyor width: 60"Equipped with: -- Pre-press flap -- Fluffer -- KARL SCHMIDT MFG. Conveyor (belt will need to be replaced; is operational)

BEACON EROPS LIGHTING OROPS ULTRA LOW SULFUR DIESEL FUEL

Regulatory Marking ROPS - Open Ultra Low Sulfur Diesel Fuel Water Spray System

Rolling Compactor

Mechanical Pyramid Section Bending Machine Model # Z302 R-PR Voltage # 220/3 50/60

great condition 220/3 50/60

Great Condition Recently Fully Serviced Profile Scrapers and Surface Scrapers No Premill/No Buffers

0.4 -3 mm (1/8") Edge cap., panel thickness from 8 -40 mm (5/16" -1-9/16"), min. panel length 120 mm (4- 3/4") and 70 mm (2-3/4") min. width. Feed Speed: Feed chain track speed 8 MPM (26 FPM) w/gear motor feed drive not under power Pre-Mill Station: 2-Motor Pre-mill (1 HP-12,000 RPM @ 200 Hz). Gluing Station:"A3" Gluing Unit for granulate adhesive application system with Quick Change application unit underneath glue reservoir, Automatic reduction of glue temperature upon interruption of work. Automatic magazine for coil (table 800 mm dia. to accommodate large coils of 3 mm material) stock Heavy Duty guillotine, strips stacking with automatic strip separation on feeding. Pressure zone with driven main roller & (2) idle post pressure rollers; Digital readout for manual adjusting pressure zone to edge thickness. Work stations: • End trim of front & rear edge (0.24 HP - 12,000 RPM@ 200 Hz motor ea. with 100 mm dia. saw blade). • Top & bottom Flush/Chamfer/Radius trimming(0.36 HP - 12,000 RPM @ 200 Hz motor ea.), sensing horizontally & vertically, DFC combination cutters for flush, chamfer, & radius trimming; (1) set of tools for 3 mm radius, digital readouts for fast adjustment. • Radius Glue Joint Scraping unit Top & bottom for removal of adhesive residue for perfect finish, sensing from top & bottom; height adjustment with top pressure beam. • Glue Joint Scraping unit Top & bottom for removal of adhesive residue for perfect finish, sensing from top & bottom; height adjustment with top pressure beam, equipped with (2) reversible cutter knives. • Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad. • Complete With: Top pressure with (2) single rows of staggered rubber rollers Transport chain with 80 mm wide with replaceable rubber pads Work piece support track extends up to 300 mm (11.8"). Individual dust extraction ports and Sound & safety enclosure.

Brandt Optimat KDF 230C Edgebander

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

Brandt Ambition 1110 Edgebander

Brandt KDF 650 Edgebander