Equipment For Sale

Carolina Blower Dust Collector Dust Blower 19" Pipe 75HP Motor (Est)

Set of (3) Bins: (2) CAROTHERS-20 UNIT and (1) WEST COAST SHEET METAL- 15 UNIT with (2) Cyclones and One Hydraulic Power Pack...20 Unit CAROTHERS Shavings stores about 4,000 cu. ft. and 15 Unit Chip WCSM stores about 3,000 cu. ft. -- the (2) CAROTHERS Units share one 8' dia. Cyclone with levelling auger and the WCSM has separate 8' dia. Cyclone. Only (1) hydraulic Power pack is included. -- Rapid Powered Discharge Bin, prefabricated for nut & bolt erection, exterior constructed of 12-gauge structurally reinforced steel. -- Chips are discharged by a set of hydraulically operated clam-shell type bottom doors for approx. 78" x 144" free fall opening, opening & closing via (2) approx. 6.5" dia. double acting hydraulic cylinders w/stroke of approx. 48", Approx. 5 HP hydraulic pump motor with reservoir; braced, wide flange steel beam support structure with approx. 14' truck height clearance. -- Complete with: Operator's platform, upper catwalk w/handrail & (1) caged ladder and full w/ribbed sheet metal enclosure with truck size access door. -- Price for complete system includes dismantling and loading.

Carrier Vibrating Conveyor 67' x 38" Bottom x 18" sides x 18" Sides x 64" Across the Top, 50HP Motor with Drive.

24 wide x 24 long,

Carrier 28ft vibrating conveyor, 24" width, 4+" high, 5HP,

Pneumafil – New Style 10’ ·· Pneumafil – Old Style 12’, 10’, 8’ ·· Torrit – 8’, 10’, 12’ ·· Carter Day – 10’ or can be cut to less ·· Airlanco – 10’ ·· Mac – 10’ MCF Style ·· Call for Availability

Carthage Brunnette Machine 21" Ring Debarker 150' Per Minute put through.

CAS (COMPRESSED AIR SYSTEMS) B73H84-E Reciprocating Air CompressorElite Series 7.5 HP 80 Gallon Horizontal Compressor @ 175 PSI / 24 CFMFeatures & Specifications: -- Access to Compressor Valves without Compressor Head Removal. -- All UL Electrical Controls -- ASME Tested Powder Coated Steel Tank. -- Auto Start / Stop. -- Bearings on Both Ends of the Crank Shaft. -- Centrifugal Unloader. -- Disk and Spring Valves. -- Fully Enclosed Belt Guard. -- Heavy-Duty Air Filter. -- Heavy-Duty (2) Stage Solid Cast Iron Pump. -- Industrial Grade Electric Motor. -- Magnetic Starter Mounted and Wired. -- Needle Bearings, and Inserts on Rods. -- Stainless Steel Flex Air Lines. -- Swedish Steel Valves. -- TEFC Drive Motor (3 Phase Only). -- Torrington Needle Bearings. -- 2-Grove B Width Motor Pulley. -- 2-Piece Tank Top Plate Design.Elite Compressor Features: -- All Basic Features. -- Automatic Tank Drain. -- Belt Guard After Cooler. -- Low Oil Monitor. -- Tank Discharge Ball Valve. -- Vibration Pads.

CASADEI RANGER MC 3012 CNC MACHINING CENTER (VERTICAL, W/ATC): -- Specifications: Flexible "Vertical" Machining Center reaches movement speeds of 131 FPM (40 MPM) in X-axis, 98 FPM (30 MPM) in Y-axis, & 66 FPM (20 MPM) in Z-axis. -- Work Capacity:Max. part size for: X-Axis is 118" (3,000 mm); Y-axis 47.2" (1,200 mm); max. part thickness 3.9" (100 mm). -- Worktable:Vertical Phenolic MATRIX Grid table with: (5) Adjustable "tubeless" pneumatic locking panel supports, (3) adjustable vacuum pods per support.Pop Up Pneumatic backstops & pneumatic side stops for material positioning on the LH or RH side of the machine for mirror imaging. -- Boring Unit:(1) Boring block with: 2.25 HP (1.7 kW) - 4,000 RPM Motor.(10) Vertical spindles with: (5) Spindles in X-axis & (5) spindles in Y-axis.(6) Horizontal spindles with (2 + 2) in X-axis & (1 + 1) horizontal spindle in Y-axis.(1) X-Axis grooving saw: 5,000 RPM; for max. 120 mm dia. saw blade. -- Machining:(1) 6.7 HP (5 kW) Router with: ISO 30 Adaptor, variable speed from 1,000 - 18,000 RPM.(1) 5-Position ATC rack mounted on the side of the working unit. -- Operator & Machine Control:CNi PC Front End + Windows "XP" Operating System; 17" LCD, TFT monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; Ethernet connection.Real-time multitask processing; programs can be transferred via USB or downloading by wire is possible. -- Complete with:(1) 100 CBM/Hr BECKER Vacuum Pump; sound enclosure & perimeter safety devices. -- Actual Model is: CASADEI - RANGER MC 3012.

CASADEI ALA 23 EDGEBANDER WITH CORNER ROUNDING0.4 - 15 mm (1/2") Edge cap., panel thickness 10 to 60 mm (.39" to 2.36"). Minimum panel length 120 mm (4-3/4") and 55 mm (2-1/8") minimum width. Equipped with: -- Quick heat-up glue system,(approx. 12 Min) 1.5 Kg glue pot capacity. -- Pressure roll section with (3) rolls - one driven. Pneumatic cut-off guillotine.Workstations: -- Double end trim, chamfers 0° - 15° -- Top & bottom flush/radius trim, bevels 0° - 15°. -- Double motor Corner Rounding station -- Top & bottom scraping for 3 mm radius, -- Top & bottom buffing (0.25 HP - 2,800 RPM motors).NOTE: Seller states that the buffing unit appears to have an electrical issue and is not currently being used by the current owner";Actual Model: "ALA 23 R"

CASADEI FLEXA 47 RMA8 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- 0.4 mm - 3 mm Max. edge thickness cap., (0.5 mm to 3 mm for solid strip edge thickness). 8 mm - 50 mm (0.3" - 1.97") panel thickness cap. (when edgebanding 3 mm PVC max. thickness is 40 mm). -- Minimum panel dimensions 80 mm wide x 140 mm long (3.15" x 5.5"). -- Automatic feed of coil banding and semi-automatic strip fed magazine (strips 1- 3 mm max.) with 3 mm PVC cap. guillotine.Equipped with: -- Teflon coated glue pot w/fast (10 - 12) Min heat-up time; 1 Kg. capacity. -- Guillotine to cut edgebanding in coils up to 3 mm thick. -- Pneumatically controlled pressure section with (3) pressure rollers; 1st drive, (2) idle.Workstations: -- Pre-milling unit with 3 HP - 8,300 RPM High Frequency motors. -- Cutting group moves on rounded ways made of hardened steel, to guarantee high precision and reliability; cutting movement from the top of the panel is synchronized by the PLC control. -- Single motor, double-end trimming saw unit with (1) 0.25 HP - 12,000 RPM High Frequency motor. -- Top & Bottom Trim station with (2) 0.45 HP - 12,000 RPM High-Frequency motors; unit features adjustable copying on vertical & horizontal floating movements, adjustable cutter-head position by mechanical digital readouts, quick release (electrical & mechanical). -- Includes (2) 3 mm radius cutters. -- Corner Rounding Unit: 2-Motor Corner Rounding unit for leading & trailing edges. -- Top & Bottom 3 mm scrape station -- Top & Bottom Buffing unit with (2) 0.20 HP - 1,400 RPM motors. -- Fixed feed speed 23 FPM. -- Actual Model is CASADEI FLEXA 47 RMA8

Panel height: 0.3 – 2.36” Coil edge thickness: .12” Strip edge thickness: .015 – .24” Max Overhang Total Top and Bottom: 0.16” Min panel width (min length of 8 ¼”: 3.54” Min panel length (min width of 3-15/16?): 5.5” Feed Speed: 33 f/min Glue Tank GP-200 Power: 2.4 kW Glue Capacity: 3.3 lbs End Trimming Unit IK/200 (each): .3 HP Cutting Speed: 12,000 RPM Blade Tilt: 0-15 deg. Top and Bottom Trimming TT/K Motor (each): .4 HP Cutting Speed: 12,000 RPM Shipping Footprint: 13' x 4' x 5' Weight: 2500 lbs Equipped With: – Pre-Milling Unit – Glue Applicator and Pressure Rollers – Edgebanding Trimming Guillotine – End Trim With 2 Tiltable Motors 0-15 deg. – Top and Bottom Trimming via 2 Motors – Profile/ Radius Scrape – Glue Scraping – Buffing

2016 Casadei Flexa 47 Edgebander 230 V/3 PH

Casadei R32 MK Pin Router

Case 621B Wheel Loader Believed to be a 1998 28,000 lb machine New transmission 2.5 yard bucket New lift cylinders Good 17.5-25 Yokohama tires Tight machine 2nd owner 7900 hours

Case 821, 3600hrs on Rebuilt Motor & Trans., Front Tires are 3yrs old, Runs Good

CASE W14 Wheel Loader with Bucket

2014 CASE 621F WHEEL LOADER 3,457 HOURS HEAT AND AC 2.7 CUBIC YARD BUCKET 172 HP ENGINE 26,711 OPERATING WEIGHT WELL MAINTAINED VERY GOOD CONDITION FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

Case 586G Forklift 73 hp 6,000 lb lift capacity 15' max fork height Machine weight 13,360 lbs Good rubber Work ready

ZERO SALES TAX FOR OUT OF STATE SALES! ZERO DEALERSHIP FEES! ZERO NONSENSE! ULTRA LOW RATE IN HOUSE FINANCING FOR BUSINESS AND INDIVIDUALS! 60 HP 4 Cylinder diesel engine! Joystick controls! Operating weight of 6,500 lbs! Shipping not included! Call for Pricing!!!!