Equipment For Sale

DMC UNISAND 2000 M3 Wide Belt Sander (3) Heads53" Width cap. Drum, Combination Head, Segmented PlatenHead Configuration:1st Head: Rubber covered contact roll 9" dia. 29 KW motor2nd Head: Combination Head, contact roll with graphite platen 21.4 KW motor3rd Head: Electronic Segmented Finishing platen with (46) segmented pads 18.5 KW motor.4th Station :Panel cleaning felt type head 1.74 kW, 460V, 3 phase, plus Air Cleaning headsSpecifications: -- 54" x 103" Abrasive belts with electronic tracking -- Computer controlled setup functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM, 3 HP feed drive -- Vacuum conveyor bed with 10 HP motor and suction fan -- Automatic conveyor belt tensioning & trackingEquipped with & Features: -- Infeed & outfeed holddown pinch rolls on all heads. -- Motorized part thickness opening with LED readout. -- 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Infeed safety stop, outfeed emergency stop, motor load meters --High efficiency dust extraction. -- Control console with monitor..Note: Dust manifold included

DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350

DMCTC 1350-M2-RP Orbital Sander (2) Heads --53" Width cap. Drum, Combination Head --Head Configuration --1st Head:10" Dia. helical grooved rubber covered calibrating roller, 26 kw (34 HP) motor. --2nd Head: Rubber covered contact roller with finishing platen 18 kw ( 28.5 HP) motor. --Specifications --Working width 1350 mm --Max thickness 170 mm --Belt size both heads 1370 mm X 2620 mm --Feed speeds variable from 3.5 -18 m/min. Feed motor 2.2 kw ( 3 HP) motor --Equipped With --Electronic sanding belt oscillation --Exhaust hoods with 4 outlets --Motor safety switch for main motor --Power rise and fall --Panel cleaning brush --Sander dim. L 2600 mm X W 2400 mm X H 2550 mm --Weight 2900 kg. --There is a crack in the plastic housing but it does not affect the functionality of the machine.

SCM DMC 90 RCS 135 2 Head 53 inch Wide Belt Sander 53" Width cap, Steel Drum, Combination HeadHead configuration1st Head: Steel Drum 36 HP Motor, 9" Diameter 2nd Head: Combination head 65 shore drum and solid wood platen, 30 HP Motor, 7" Dia. drumSpecifications: -- 54" x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computer controlled; set-up functions with a keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, -- Motor load meters. -- 2-Roll infeed conveyor extension; -- High-efficiency dust extraction.NOTE: Specs have to be verified

D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

DMC UNISAND K 1350 M2 1,350 mm (53.15") 3-Head Veneer SanderFor lacquer sanding, veneer cut, light calibration cut.NOTE: The following specifications need to be confirmed by Seller.Specifications: -- Working Thickness 4 - 200 mm (0.16" - 7.87"). -- 1st Head: TA Cross belt sanding unit, with Electrically-controlled link sanding pad, 150 mm x 6.550 mm (5.91" x 257.87") Sanding belt, Variable sanding belt speeds 2 - 20 MPS (6.6 - 65.6 FPS), 15 kW (20 HP Motor), -- 2nd Head: "R-320" 320 mm Dia. (12.60") Shore 40 SH Spirally-grooved contact roller, Soft rubber version, 1,370 mm x 2,620 mm (53.94" x 103".15") Sanding belt, Variable sanding belt speeds 2 - 20 MPS (6.6 - 65.6 FPS), 15 kW (20 HP Motor). -- 3rd Head: Superfinishing pad with "EPICS" Electronic sectional pad, (46) Sections, 1,370 mm x 2,620 mm (53.94" x 103.15") Sanding belt, Variable sanding belt speeds 2 - 19 MPS (6.6 - 62.3 FPS), 15 kW (20 HP Motor), Pneumatic belt tensioning, Intermittent belt-emitting device, Automatic infrared band control.Equipped with: -- Oscillating belt cleaning blowers on all heads. -- Vacuum conveyor feed belt, with Variable feed speeds 3.5 to 18 MPM (11.5 - 59.1 FPM), 4 kW (5-1/2 HP) Drive motor, 15 HP Blower motor with Fan silencer. -- 200 mm (7.87") Dia. Panel cleaning brush with 1.5 kW (2) HP Motor. -- "HYDRA V-PAD" Touchscreen control.Weight: 10,500 Lbs.

SCM (DMC) SD90 202 ( Head ) Wide Belt planer sander53" width cap, Drum, Combination HeadHead configuration1st Head: Steel Drum, 15 HP2nd Head: Combination head with 65sh drum and Solid Wood Platen 15 HPSpecifications -- Working Width: 0.053 inches -- Min/Max thickness to be machined (with mobile table): 0.15" - 6.69" -- Min/Max thickness to be machined (with fixed table): 0.15" - 7.87Equipped with & Features -- Sanding belt width/lenght: 0.053"/0.103" -- Standard main motor power: 15 HP -- Feed belt motor power: 0.8/1.7 HP -- Feed belt speed: 14.76/29.52 ft/min -- Height of fixed table: 88.97" - 96.85" -- Height of mobile table: 89.13 -- Dimensions (LxWxH): 101" x 75" x 96" -- Weight: 8700 pounds

Daewoo G25S Forklift

156" long x 60" wide x 80" high (3) vertical pneumatic Clamping bars (7) clamps that can be placed horizontal or vertical on perforated surface

This unit has been in storage for some time and will need some TLC.

DANCKAERT - 44 , ...ResawAir Strain 44"; x 5"; Bandsaw.Features & Specifications: -- McDONOUGH Center Split Feed Works. -- Wheel is supported on both sides - not cantilevered. -- Pressured guides. -- McDONOUGH Infeed Rolls. -- Max. Cut: 14";. -- New Dynamic brake. -- 60 & 100 HP. -- Control Cabinet (has battery backup and resistors to prevent spikes). -- Infeed & outfeed systems are the same. -- 24 ft. Long Camel Back chain (has air bags that are controlled by photo cell to raise & lower and index 1-board at a time). -- Max. length of lumber: 24 ft.From Seller: "The machine has a new VFDD 100 HP and a new WEG Severe Service 60 HP motor. All new hydraulic motors, caramel back chain, and roll cases."NOTE: Needs hydraulic unit.

1-3/4" Spindle dia., 7.5 HP motor, cast iron table. -- Includes: A & B 4-Speed belt driven Power Feeder with SCR feed control.

(5) Danfoss VLT-5000 VFD 50Hp Max

Danzco Pull through delimber 18PT Log diameters: 18” to 5” Used Danzco pull-thru delimber Model: 18PT Video of delimber working Danzco still supports delimber with parts Honda motor runs great Contact us for pricing & a freight rate

Datsun Propane powered forklift. Dual front tires. 8000 pound lift. Very strong.

3/4 HP 1725 rpm motor 115/208/230 volt single phase approx. 12” x 30” table Jacobs chuck approx. 3/4” footpedal Assorted fixtures and tooling as pictured.

Davis & Wells Horizontal Boring Machine Call 800-459-2148 for more info.

DAYTON - 3Z968, ...2-Stage Reciprocating Piston Type Air Compressor -- 10 HP Motor; 2-stage rotary screw type; 115 CFM @ 125 PSI; 120-gallon horizontal tank. -- Complete with: All controls and starter.

Grinder feeds a holding tank, which the material is automatic metered and feed to the furnace. Feed is temperature controlled.

7.5 HP Lubricated rotary vane vacuum pump, max. 145 CFM, max.; heavy duty construction, compact design, small foot print, high tech vane material provides long life. Single-stage pump with an integrated closed loop oil recirculation system. Air cooled design with gas ballast valve and internally mounted inlet check valve. Float type oil-recovery valve ensures maximum air/oil seperation. -- High efficency multi-stage exhaust filter removes 99.9% of exhaust smoke. -- Complete with: 2-Year warranty from date of shipment, provided the pump(s) are operated per instructions given in the Operations and Maintenance Manual.