Mobile Wood Grinders For Sale

New 2023 BANDIT 1425 14"" Beast Grinder Includes the Following: - Cat C3.4 Engine with 120HP - 25"" Wide Feed - 40 Gallon Hydraulic Tank - 30 Gallon Fuel Tank - Remote Hydraulic Oil cooler & Cover - Standard Bandit Green Paint - NACD Manual Clutch - Radio Kit with Remote - Steel Chain infeed conveyor - Tandem Axle with Air Brakes - Bolt on Aluminum Fenders - Magnetic Head Pulley on Discharge w/ Steel Collector Pan - Non-Adjustable discharge w/ 7' height - Grinder Cutterhead with Rakers - Equipped with double short shingle teeth - Installed: 3"" Diamond Screen - Shipped Loose: 2"" Diamond Screen - Shipped Loose: 4"" Mod Diamond Screen - Shipped Loose: Extra Shingle and Blunt nose teeth 5 YEAR/5000 HR PLATINUM WARRANTY (CAT ENGINES)

2020 Bandit 3680T BEAST Tracked Horizontal Grinder - 1416 Engine Hours - 900 Grinding Hours - Cat C27 w/ 875 HP - PT Fluid Clutch - Remote Control - Automatic Greaser - Automatic Chain Oiler - On-board air compressor - Adjustable Discharge - 36"" Capacity - 30 Tooth Cutter mill This machine was just ran through by the Quality Equipment & Parts Service Department. Bandit dealer of 10 Years. - Infeed Chain: New Headshaft and Tailshaft, new bearings, some new infeed slats - New teeth & rakers on cuttermill - New Screen & Gate - New Poly slide boards on Primary Discharge - New Anvil Bar - On-board air compressor serviced - New grease lines

2010 horizontal grinder/chipper mobile track 2800 hours New twin Disc clutch New conveyor New 3 stage pump New cutter mill drive belts Currently mill is converted to chip knives Have all cutterbodies, teeth, screens and gate to convert to grinding.

2022 Bandit SG40 Stump Grinder, Kohler 38 hp EFI Gas with 238hours, New Belts, 18” diameter x 1/2 thick New Revolution cutterwheel with 47” swing, Adjustable rubber tracks. L 100.5” W 29” H 48” Lbs 1,500 lbs Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

Micro Chipper C-27 Tier II 875 HP 5173 Hours

2001 Bandit 3680 with Cat 3412 860hp, with 8,000 hours. Radio remote, and Magnetic head pulley. Redone summer of 2021. Ran sept 21-March 22 parked until June 22 did a 3 week job then parked until November 22. Ran until March 23. Newer floor, Frame restructure, All hydraulic cylinders and hoses replaced. Hydraulic tank drained and cleaned. New: Clutch, Drive belts, Starter, Anvil, 2 augers and bearings and chain, Discharge top bearings and motor. Length: 44’ Width: 10’10” Height: 13’ 6” Weight: 62,500 lbs. Fuel Tank: 400 gal. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2023 Bandit SG40 WALK BEHIND Stump Grinder with only 41 hours. Features an aggressive cutter wheel drive system, enhanced operator visibility, and enhances stability. Operator controls are mounted on a 3-poisiton console. Two joysticks control the travel of the unit, while a single, easy to use joystick controls all cutter wheel functions. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2003 Bandit Beast 3680 350HP Cummins - Rebuilt engine, injectors, PTO and Twin Disc clutch - New radiator/tanks - New hydraulic motors on outfeed belt and discharge screws - New Vulcanized outfeed belt - Has remote control but solenoid valves have been disconnected. This Beast of a grinder ran daily for 2+ years for us and was a champion, did whole log chipping and chip regrind no problem. Could use some patching in the grinding chamber and discharge belt frame, but is ready to run as-is. $75,000

2015 Carlton SP7015 Stump Grinder with 1,400 hours. 66HP Kabota Diesel Engine, Blade, 4 x 4 with a trailer. Weight 3500 Lbs. Length 10’ 6” Height 52” Width 35” Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

CAT C27 TIER 4F DIESEL ENGINE (1050 HP) PT TECH HPTO15 HYD CLUTCH AUTO REVERSING FAN SYSTEM 40" X 60" HAMMERMILL (24 HAMMER PATTERN) FORGED DRUM OFFSET HELIX ROTOR 8" ROTOR SHAFT, 3.75" THICK, 5400LBS 40" TOP COMPRESSION FEED ROLL LIVE FLOOR W/4 WDH-120 CHAINS, 6 STRANDS WIRELESS REMOTE AND TETHERED REMOTE 60" DISCHARGE STACKING CONVEYOR 16' DISCHARGE HEIGHT UNDERCARRIAGE 700MM TRIPLE GROUZER MAGNETIZED END PULLEY W/COLLECTING SLIDE TRAY CBI MDS - METAL DETECTION SYSTEM

CAT C18 TIER 4F DIESEL ENGINE (765 HP) AUTO REVERSING FAN SYSTEM 48" WIDE x 40" DIAMETER HAMMERMILL FORGED DRUM OFFSET HELIX ROTOR 6" ROTOR SHAFT 48" WIDE X 30" DIAMETER TOP COMPRESSION FEED ROLL LIVE FLOOR W/4 WDH-120 CHAINS, 4 STRANDS WIRELESS REMOTE AND TETHERED REMOTE 48" DISCHARGE STACKING CONVEYOR 15'4" DISCHARGE HEIGHT UNDERCARRIAGE TRACKED MAGNETIZED END PULLEY W/COLLECTING SLIDE TRAY CBI MDS - METAL DETECTION SYSTEM

2023 CBI 6800 Wood Grinder -233 hours -C-27 (1050 H,P) -Tracked -Like new machine

Great running Diamond Z DZH4000 with a Cat C18. Everything works as it should. Has a rod Puller

2006 Morbark 6600 HG Rebuilt CAT 1000 Hp engine Approx 2100 hours Magnet Great for processing pallets, brush, green waste & more

CAT V12E, 750HP DIESEL, FOLDING DISCHARGE CONVEYOR, HYDRAULIC REVERSING FAN, AND TRI-AXLE CARRIER. IN GOOD CONDITION.

2012 Morbark 3800XL Caterpillar C18 – 700hp 5807 machine hours. Recent rebuild on the Cat engine. New mill components.

2002 Peterson 7400a Horizontal Grinder -End of summer 2022 we installed NEW -Cylinder packs and bearings -Both turbos -High pressure oil pump -Ecm -Injectors -All gaskets and orings -Oil pump -Twin disk clutch -Had the heads completely rebuilt -Radiator completely gone through -Rebuilt feed floor -Rebuilt mill -Mill bearings checked for clearance and passed -All belts and chains in good shape -Alot of extra screens and parts come with it. Some are brand new

2019 Peterson 2710D Grinder -4550 hours -C18 CAT Engine764 HP -Motor replaced at 3500 Hours by CAT with Papers -Clean machine ready to work

2023 Rayco RG-80 Self Propelled Stump Cutter, ONLY 280 Hours, Ford 85 Hp Gas Engine, (Ford Fiesta Engine) Great Parts Availability, 2 Year Warranty Remaining Through Ford, 2 Speed Drive, Hydraulic Ground Speed, Hydraulic Swing Speed, Hydrostatic Drive, Pillow Block Bearings were replaced to Timcon Bearings, Wireless Control Remote. Like New Machine Priced NEW at $89,000.00. WEIGHT 3,230 lb, LENGTH 142? HEIGHT 55? WIDTH 51? blade extended, dual wheels on / 35.5? blade folded in Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

Rexworks Maxigrind 425 Portable Horizontal Grinder w/Cat Engine, Tandem Axle 5th Wheel Trailer