Equipment For Sale

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,Equipped With:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single cycle & continuous automatic modes;2 HP hydraulic feed pump, 12-gal. hydraulic pump system;Note: Riggers are required for loading

(14) spindles with 1-1/2 hp motors on each. On/off switch for each motor. chucks adjust to grip up to 1/2” bit stroke adjustable from 4” to 10” 121” x 39-1/2” table with (4) hold downs Adjustable speed hydraulic feed 230 volt 3 phase

CEMCO - 4000, ...2-Head Wide Belt Sander38" Width cap. - Drum, Platen configuration.Head Configuration:1st Head: 40 HP -1,780 RPM rubber contact drum head.2nd Head: 30 HP - 1,775 RPM platen style head.Specifications: -- 3 HP 230/460/60/3 Feed motor with TOSHIBA VFD controls. -- 15 - 60 FPM Conveyor feed speed . -- 30 HP - 3,525 RPM Vacuum blower. -- Vacuum type rubber conveyor feed belt. -- Push button controls and amp meters. -- Electric ProScale digital thickness readout. -- YASKAWA Varispeed F7.Equipped with & Features: -- VFD abrasive belt drive system. -- Outfeed workpiece dust cleaning enclosure.Includes: Replacement abrasive belts and belt racks.

CEMCO ‘SUPER HEAVY-DUTY’ SANDER 3 Head Sander with 3 Drums and an Extra Drum. Specs: Drum 1 - Hard Rubber Sands lumber, surface particle board, or MBK Takes 4-5/1000ths of surface w/ 80 Drum 2 - 65 lb, Soft - Custom For hardwood / veneers grip 100-120 grit #3 Hardware Takes 4/5000ths off Drum 3 - Smoothing Bar that is 4" wide. Contact is about 4" Takes 2 – 3/1000ths off - Comes with Spare Smoothing Bar - Drum 1 @ 75 HP and Drum 2 @ 50 HP motors can run @ 100 feet per minute - Was run at about 65 - Sealed Bearings - McGuire Bearings has them if needed - In & Out “Free Wheels” Belt Call 800-459-2148 for more info.

CENTAURO T5-1600 Hydraulic Copy Lathe with (2) back knives; Specifications: -- 63" (1,600 mm) Max. between centers, 4/5.5 HP main motor, two speed selector switch, 900 - 1,500 - 1,800 - 2,250 - 3,000 and 4,500 RPM spindle speeds. -- 1 HP Hydraulic power pack for variable speed carriage 0 - 19 FPM carriage; return speed 24 FPM, hydraulic tailstock with Pressure Reducing Valve (PRV) for fine control of pressure, especially helpful for small and/or slender turnings. Equipped with: -- (2) Independent copying units, (1) for roughing and (1) for finish cutting. 1st, 2nd pass & auto feature with 2nd pass active it will cut the pattern 2 times automatically and sequence the tools between cuts. -- Revolving steady rest, max. dia. 140/100 mm square ( 5.5"/3.9"), and for max. dia. 90/65 mm max. square billet size. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. Includes: -- (2) Back slides manually operated with knives for making dowel ends; 45/26 mm drive center for headstock and 12 mm center for tailstock, (2) V-type gouges with 0.6 & 3.5 mm cut radii.NOTE: Ex-Factory handles import/export to just about any country in the world.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with (2) Copier Heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and attachment for revolving steady rest; 3-1/2" max. square part size with revolving steady rest, 5" max. with copying unit, 5.8" stroke of copying unit. -- Capacity: 19-5/8" Max. length for manual turning. 9.8" (250 mm) Max copy dia., 6.8" (175 mm) max. square section without steady rest. -- Includes: Drive center with, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center.Note this machine has no top Back Knife for plunging with a form tool.

Tool Grinding Machine for V-Type Gouges. -- Tabletop design saves space. -- Works with most sizes of v-gouges. -- Optional standing base $275.00. -- Diamond stone cutting wheels, ordered seperately, price $420.00 each. -- Please specify required voltage and lathe model when ordering wheels.

CENTAURO TC-1200 Copy Lathe;47-1/4" Max. between centers. -- 4-3/4" Height of centers over bed. -- Max. copy dia. 6" (4-1/8"). -- Max. dia. permitted by traveling steady 3-1/2" (2-1/2"). -- 4 HP main motor, 900 - 1,500 - 2,200 & 3,540 RPM spindle speeds. -- 1 HP hydraulic variable speed carriage with tool post and revolving steady rest. -- (2) Independent gouges working in conjunction with the traveling steady rest. -- Variable speed hydraulic saddle movement. Standard Equipment & Specs: -- Drive center with (2) interchangeable heads 1" and 1-3/4". -- Tailstock revolving center 1/2". -- Traveling steady rest max. 3-1/2" (square 2-1/2" x 2-1/2") with reduction bushing. -- (2) Vertical Tantung gouges, radius 1.2 mm and (1) precutting tool. -- Work-piece centering device. -- Tool support rest for hand turning. -- (2) Dust extraction ports 4" dia. -- Motor protection switch. -- Emergency push button. -- Front sliding safety guard. -- Standard: Service tool kit and Abrasive stone for cutting edge dressing.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with two copier heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and revolving steady rest attachment; 3-1/2" max. square part size with revolving steady rest, 5" dia. max. with copying unit, 5.8" stroke of copying unit. 19-5/8" max. length for manual turning. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. -- Includes: Drive center, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center. -- Note this machine has no top Back Knife for plunging with form tool. -- Machine manual included.

Extremely well-built Edge Sander with 5 HP - 1,200 RPM TEFC Motor. -- (2) 11" x 60" Cast iron platens. -- 10" x 172" Abrasive belt size. -- 0.5 HP oscillation motor to produce (150) oscillations/Min with 1/2" movement. -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table. -- All tables with 30° tilt up & 45° down. -- 5" Vertical table travel, 5" lateral side table travel and 4-1/2" lateral end table travel. -- Convenient hand wheel adjustment. -- Large 10" dia. x 10-1/2" face direct drive pulley with 4-1/2" dia. x 10-1/2" idle pulley for a huge sanding surface. -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

Nice CF Nielson BP5500 Press. The plant shut down in 2014. The machine was run again for a test in 2016 and everything was in good working condition. They have the dies and pistons to make round and octogonal logs. - Briquetting press CF Nielsen BP5500 - Dies to make 3’’ round logs and 2½’’ octogonal logs - Lignin dosing system - Water pump to add water if material too dry - Home-made automatic speed adjustment with encoder. - Briquette breaker from CF Nielsen at the end of the cooling line - Home-made flying saw with lenght asjustment at the end of the cooling line too with capability to switch from the saw to the breaker. - Can run up to 1200kg (even 1400kg I think) per hour depending on material and briquette shape - Cooling line can be opened to make pucks also. - 575V AC motors - Installed in 2008 - 10,865 hours

CFORM Edger/Rip Saw - model CKM160 This machine was purchased new and installed the beginning of 2023. It has less than 20 hours. The seller changed applications. Machine is ready to load. Photos coming! Manufacturer information: Double Edgeing & Slicing Cutter the value of lumber with clean edges can often exceed the value of rough-cut boards. In one pass, this Twin Blade Board Edger takes boards fresh off the mill and turns them into clean, square edged lumber. This edger is easy to use, with one fixed blade and one moveable blade that adjusts with a manual dial. Easily select the precise size of lumber you need. Lower the perimeter fence when you need to edge only one side of a board. Features: Movable finger iron platers for safe guidance and protection. Maximum 15 raws circular saws, adjustable distances. Hydraulic upper roller pressure and movable cyclinders. Maximum cutting height (inch)6 5/16?, 4 11/16?

Challenger Slow Speed Wood Grinder

CHALLENGER CG 300 3037FT Vertical Hopper Fed Low Noise Grinder, Reconditioned in 2008Specifications: -- Cutting chamber size: Approx. 40" x 40". -- Hopper opening size 40" x 65". Equipped with: -- 14" Dia. x 39" L Rotor, with Diamond-shaped 4-way indexable knives, 1-Piece Counter knife, & 50 HP Rotor motor with High torque gearbox drive. -- Interchangeable Screen, with 6" dia. chip collection outlet. -- Hydraulic ram, with 5 HP Hydraulic motor. -- Heavy-duty construction with Stress-relieved shell & frame, Heavy-duty outboard roller bearings, & Front hinged access doors. -- Control, with PLC & Star delta starter.Complete with: -- (1) 3/8", (1) 5/8", & (1) 7/8" Screens. -- 20' L Motorized Outfeed Incline Conveyor, with Overhead magnetic particulate removal system.NOTE: Auger available if desired.

Challenger Grinder with 10' Infeed Steel Belt, On Board Hydraulics.

This grinder was removed from service in good working condition. It is ready to load/currently in storage 200 HP Main Motor Cutters 117 F-Cutters Screen (4 ) 22" Diameter Wide with 1-1/2" Holes The width is 51” and the height is 17” (infeed opening)

Recently replaced the engine

Unit was (reconditioned) in 2013. Bottom Flail Assembly replaced in 2014. Unit has a remote. CALL FOR DETAILS

Champion C70A Grader -3478 hrs -Cummins 4BT power -Hydrostatic drive -Articulated with front blade and fold down scarifier -Enclosed cab with heat -2 of the cylinders rebuilt, and a new cylinder made for the front blade. -Ex street department machine Clean machine!!!!!

Believe Champion Swing Hammer Hog 30"