Equipment For Sale

Complete Sawmill Operation Asset list includes: Corley 2-HB Sawmill: 200 HP, log deck Corley 8x48 Gang Edger: 24" Blades 4-Head Trim Saw 2-Head Trim Saw Gabbiani Gang Rip Saw Wood-Mizer 4-Head Resaw Bob Hanna Double Notcher Precision Chipper: 48", 100 HP Motor Pendu Stacker (2) Case Forklifts Tigercat Knuckle Boom Loader with Bucksaw Mack semi (2) Pallet Dismantlers John Deere 744 Loader with bucket and grapple Miner 2-Blade Edger Misc: Motors, hydraulic packs, decks, conveyors, rollers, gear boxes Includes: All electrical and controls

30” x 165’ Concave Belt, Conveyor/Shaft Mount Drive

32" Concave Belt Conveyor

30' Concave Belt Conveyor with 24" belt

7,000 Square feet of cloth Approx 70,000 CFM (2) 37" Positive Fans: 150 and 125 HP Ready to load on your truck!

CONCEPTION CRP-180 Short Block Feeder Infeed ConveyorSpecifications: -- About 4 m long X 1.2 m wide, 2-ply rubber belt, friction back with Photocell for automatic operation -- Short Block Feeder; Blocks to be 25mm longer than width -- 14' rotating carousel with adjustable speed via VFD with Motorized wheel to avoid blockage -- Exit opening adjustable to the block width -- 200 mm x 7m long belt conveyor to carry the blocks to index rolls; Servo indexer controlling the flow powered by an electric motor; Speed-up belt powered by an electric motor -- Wane System: Scanner to detect wane integrated in conveyor -- Display screen to show wane detected; Kicker to kick blocks that are not in good orientation -- Conveyor to return it into the spreader belt conveyor -- Automatic Operations

750 kw Generator This was owned by a hospital. Seller purchased both units and never used them.

PRICED REDUCED Cone 2-Saw Independent Arbor Optimized High Speed Edger, 4/4 to 4" runs 14 boards per minute W/ Tailing Device W/ Innovec Generation III Controls W/ Lots of Spare Boards & Parts to Keep Software Running, Includes MIC Unscrambler, with even ender up top. Scanning Bar and hi-speed indexible infeed and tailing belt outfield. On the ground and ready to load. Taken out with Videos and instructions to re-install. A must. Ref #131

CONQUEST 1-23H CONSTRUCTION / LINE BORERUSA-Made 46-spindle Horizontal/Vertical Boring Machine.Specifications: -- (2) 2 HP BALDOR Motor to drive a helical gear head with spindles on 32 mm centers. One head with (23) Spindles in the vertical plane and One head with (23) spindles in the horizontal plane. -- Pneumatic head movement to reduce operator fatigue. -- 20-1/2" x 36" Cast iron front table.Complete with: -- 98" Back fence with repeat stops. -- (2) Pneumatically operated index pins & (2) pneumatically operated holddowns. -- Collets that accept 10 mm shank bits. -- Bit requirements of 10 mm shank. -- Foot pedal control....$150.00 crate charge.

CONQUEST 1-23H Horizontal 32 mm Boring Machine;Specifications: (1) 23-Spindle horizontal boring head, 2 HP "BALDOR" motor, helical gear driven spindles spaced on 32 mm centers, 3,450 RPM; cast table. -- Equipped with: Pneumatic head activation, side fences. -- Complete with: (2) Pneumatically activated holddowns and foot pedal. NOTE: This unit has 2 sets of arms. All the screws have been replaced for the drill bits. Ready to go to work!

Hydraulic pump power unit, 3500 psi, 29 GPM. 100 gallon tank, 30 hp Continental Pump model: HPVR-29B35-RF-O-1R-A 100-gallon Tank MFG: HTS/Hydraulic Technical Service, Eugene OR. Hydraulic power pack 3,500 psi. Pump P/N : 1021823 Pump Disp. 3.97 in3/rev 3500 PSI max pressure, GPM: 29/30? 4 Nachi Solenoid hydraulic valves 30 HP Toshiba motor: 230/460,1770 RPM, Frame 286TC, TEFC, Duty Cont., Inverter Duty, VPWM, Severe Duty, Ins. F., Date: 2014 on tank Tank Heater: Watlow, 1ph, 1500 Watts, 240/480 volt, Prior use and stored inside a building. Approximate Shipping dimensions: 54”W x 54” L x 84” tall, 1,900 LBS. a pallet/crate will be built at NO cost for shipping, tank has been drained of oil. Contact us for a shipping rate

Continental Automatic Gas Fired Boiler S/N L 196710

Grizzly feeder Hopper Front End loader hopper

Cooks edger, 6" thick x 36" wide capacity, 2 movable blades, set up for tailing belt, hyd drive, includes controls, tailing belt, dust auger under edger, nice condition and ready for production

Cook's AC36, Fully Hydraulic, Perkins 400 C Series 65 HP Engine, Engine has been serviced with new filters. Starts easily and runs well, New fuel tank. New hydraulic tank. Hydraulic pump rebuilt. New idle wheel. Idle wheel tensioner replaced with all new factory parts Call 800-459-2148 for more info.

Cook's 2019 AC 36 Fully Hydraulic Band Sawmill, 67 HP Yanmar Diesel, Computer Setworks, Debarker/Mudsaw, Remote Engine Shutdown and Throttle Control, Mega Guide System, 26" All Metal Bandwheels, Gearbox Head Raising System, Dual Axles with Brakes. 14" Split Strobe Saws, Trailer Package, Cat Claw Dual Tooth Setter, Cat Claw Sharpener, Mega Parts Package:? (60) Super Sharp™ Blades (4) Spare 2" Guides (10) Replacement Guide Bearings (2) Spare Drive Belt (2) Spare Pump Belt (2) Sharpener Grind Rocks (1) Metal 4ft. Cant Hook (1) Timberjack (1) Hand Set Checker (1) Blade Alignment Tool (1) Spare Tire 2019 Model 871 Hours on Saw - Has Bill of Sale Call 800-459-2148 for more info.

Cook's HD-32 Manual Band Sawmill - 2022 Cook's HD-32 thin kerf sawmill package #3 - 25 HP Kohler engine with just over 1 hour on the mill - Cap 16' x 32" - 12 V loading winch with ramps - Trailer with spare tire - 12 V head up/down - Includes: 10 new super sharp blades, metal cant hook, blade alignment tool, stainless steel bunks, 10 new blades, 5 gallons on copper naphthenate concentrate for treating lumber, Solar trickle charger for winch - Mill can be towed distances with ease - Weighs approx 2500 # Call 800-459-2148 for more info.

COOK 2 SAW EDGER-BOTH SAWS SLIDE W/9' INFEED ROLLCASE, 20HP MTR & 7 1/2 MTR S/N 3682981

MLS Number 10679774 Cook Grade Lumber Resaw 30 HP Will saw 16" wide No return 1 1/4" to 2" blades

Cook 6" x 48" 2 Saw Edger. W/ in & out feed.