Equipment For Sale

2015 Bell 6000 Firewood Processor -2048 hours -4.4 liter cat engine -Enclosed cab with heat but no A/C -8. 12. and 16 way wedge -8' live deck with 5.5' spacing -Runs and operates as it should

Beloit ring type debarker, electric drive, working condition

Benshaw 200 hp. soft start

Benshaw 150HP Soft Start

Benshaw 75HP Soft Start Mdl CBRDB6-124-12

Benshaw 150Hp Soft Start

2002 Benson Chip Trailer Open top 45'

Track System Replacement Rollers. BERCO NEW rollers! And all the parts, pins etc. see photos. There are 18 rollers. Call 800-459-2148 for more info.

(3) 60HP Motors (1) 75HP Motor with Large Hydraulic Holding Tank

20HP HYDRAULIC UNIT

Bertheson Press Platform size 51 Wide X 102 Long with 2 16 ft shuttle driven aluminum runner platforms. Pressure 2500 psi and we ran a temperature of 350 degrees for Tego and 165 degrees for plywood. The Press can laminate Tego Film glue or pva c glue. This press is a double shuttle and can laminate up to 14 ft by double pressing on shuttle. We can get the press operational if you are interested. We only have to hook up the power. Very good condition!

YM-800 1 YARD 4 OR 5 TINE Orange Peel GrappleSpecifications: -- Operating Weight 2,400lbs -- Opening Width 71 1/8" -- 4 or 5 Tine in stock - Ready to ship -- Rotating -- Hanger for Extra Cost

Manufacturer Specs premill hot glue end trim top/bottom trim corner rounding scraping buffing Computer interface

Biesse Akron 440 Edgebander Premill Top & Bottom Trim Corner Round Edge Scrape Glue Scrape Buffing Unit 12-18 m/min Feed Speed All work units are servo controlled

Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

Biesse Elix K3

BIESSE AKRON 1330 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Computer controlled interface for workstations with servos and pneumatic positioning devices. Programmable selections for 1-touch changeover between edgebanding types and thicknesses.Top Pressure Beam with automatic adjustment from the machine control. -- Working Capacity: Edgebanding thickness, 0.4 - 5 mm capacity. Min. panel width 85 mm (3.3"); min. panel length 140 mm (5.5"); panel thickness 10 - 50 mm (0.39" - 1.96").3 HP (2.2 kW) Variable Feed Speed from 10 - 20 MPM (32 - 65 FPM).Front-End Equipped With: -- Premilling Unit with "Autoset" automatic intervention, Strip & Coil Edge magazine, automatic shear type guillotine. -- Hot-Melt Glue System: Teflon coated glue pot, digital thermostats with automatic kick-down when machine is in idle mode.Pressure Section with (1) large dia. "non-stick" coated drive roller & (5) Teflon plated idle rollers with servo positioning NC controlled material thickness adjustment.Workstations: -- End Trimming Unit:NC controlled end trimming unit, 0.33 HP (0.24 kW) - 12,000 RPM motors;Motors travel on (2) straight slides and pneumatic tilt 0° - 15° on horizontal. plane -- Top & Bottom Multi- Function Flush/Bevel/Radius Trimming Unit: NC Controlled 2-motor Top & Bottom Multi- Function Flush/Bevel/Radius Trimming Unit, 0.3 HP (0.24 kW) - 12,000 RPM.Servo driven positioning of motors for different edge trimming profiles & positions. -- Corner Rounding Unit:2-motor 0.3 HP (0.24 kW) - 12,000 RPM motors for trimming leading & trailing upper & lower edge/corners with "Fast Position",Unit can be used as a second top & bottom fine trimmer as well. -- Profile Scraping Unit:Top & bottom 2 mm or 3 mm thick PVC banding, digitals for horiz. adjustments. --÷ Flat Scraping Unit:Top & bottom glue scraping unit. -- Buffing Unit: Top & bottom Buffing Unit, 0.5 HP (0.37 kW) - 2,800 RPM motors), units tilt 0° - 30°Operator & Machine Control: -- Biesse SMART TOUCH 7" + Windows operating system, user friendly touchscreen control panel for workstations, rotating operator control panel w/keypad and LCD readout.Graphic 7" display touch screen. High-resolution screen for defined and intuitive images and text. Integrated 4GB hard disk for filing media files and the programs back up.USB port for managing in a simple and efficient way multimedia files, programs and updates. Ethernet port for connecting the machine to the net.Complete With: -- Insulated sound enclosure over all trim stations with split dust hood, viewing windows. -- Actual Model is BIESSE AKRON 1330 A

BIESSE AKRON 1445 A SINGLE SIDE EDGEBANDER Edgebander (W/PRE-MILL & CORNER ROUNDING): -- Specifications: &#9679 Min. panel height: 10 mm; Max. panel height: 60 mm; Height of edgebanding material: 14 - 64 mm; Thickness of edgebanding material in rolls: 0.4 - 3 mm; Thickness of edgebanding in strips: 0.4 - 10 mm.Min. panel protrusion from the track: 25 mm; Panel length: 140 - 3200 mm; Min. panel width (with length 140 mm): 85 mm; Min. panel width (with length 250 mm): 50 mm.Multi Speed Track-Feed Kit with (4) processing speeds of 8-12-15-18 MPM. (26-39-49-59 FPM), max speed is 15 MPM (49 FPM) when Corner Rounding, 12 MPM (39 FPM) for panels over 40 mm (1.57") height.Glue & Pressure Section: &#9679 Infrared lamp IRL 700; Gluing unit Quickmelt QM 703 EVA melting glue. Special glue container for PU glue; Additional glue container for EVA gluing unit with melting device; Automatic edge feed; Cutter knife; Pressure zone with 1-Drive & 2 pressure rollers.Working Units: &#9679 Anti-Adhesive Unit ADZ02: for ease of good cleaning before Pre-Milling. -- Pre-milling unit RT02; with "AUTO-SET", 2 x 0,8 kW, 12000 RPM motors, Diamond Cutters; front/rear inclination 0° -15°. -- NC Controlled Gluing, edge feeding, and pressing unit VC-511. -- End trimming unit IN-801; with 2 x 0,8 kW, 12000 RPM, front/rear, inclination 0° -15°. -- Rough trimming unit RS-502: 2 × 0,65 kW, 12000 RPM top/bottom. -- NC Controlled Fine trimming unit RF-02: 2 × 0,65 kW, 12000 RPM top/bottom; Unipoint tilting from 0° - 45° to facilitate adjustments. -- Sliding Liquid Unit for Corner Rounding. -- (2) NC Controlled Multifunction Corner Rounding unit AR02E, 0,65 kW each, for Corner Rounding, Straight Work pieces, Post and Soft-Forming 90° -180° degrees. -- NC Controlled Edge scraper unit RB02; Glue scraper unit RC02. -- Cleaning Unit LPT02 for scrapped edges. -- Buffing unit SZ02: 2 × 0,37 kW, 2,800 RPM motors. -- Hot Air Blower PH-501; To re-activate color of plastic after scrapping. Machine Features:&#9679 Top Belt pressure beam. The top presser comprises a rubber belt with a stain-proof coating. The thrust exercised on the panel is provided by springs housed on techno polymer connecting rods. -- Automatic track lubrication system with dynamic track absorption. -- Manual infeed system for narrow pieces. -- One coil automatic edge feeding. -- "TEKNO GLUE" system for Optimal gluing in any working condition. -- Pre-Melter QM-703 for EVA Glue. -- Hybrid gluing head for granulated EVA and Polyurethane glue. -- Pre-Melter QM703 for Polyurethane glue in cartridges. On-demand top-loading pre-melter for PUR glues. -- Adaptive infra-red lamp AdlRL-700, to heat up the panel side before the glue application, in order to optimize the adhesion process. -- Independent pneumatic exclusion of the top/bottom fine trimming unit. Operator & Machine Control:&#9679 Biesse, Windows-based, 21.5" full HD "SMART TOUCH 10" control & operating system.Complete With:&#9679 Kit p

BIESSE STREAM A 6.0 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + NC Axis PackageFeatures: -- "NC Axis Package": The machine adapts to the process being executed based on the edge's thickness and material.Machine management ...100% touch with no need for external devices. - Intelligent language management.Easy program management and usability with rapid transition from one machining operation to the next. Specifications: -- Edgebanding Capacity: Edge thickness for strips: Min./max. 0.4 - 22 mm (0.02" - 0.87"); coiled material from 0.4 - 3 mm (0.02 - 0.12").Panel thickness from: 10 - 60 mm (0.39 - 2.36"); workpiece width: Min. of 85 mm (3.34"); workpiece length: min. 140 mm (5.51").Feed speeds of: 12 - 18 - 20 - 25 MPM (39 - 59 - 65 - 82 FPM).Machine Infeed Configuration: -- Pre-milling Station:(2) 1.8 kW (2.4 HP) - 12,000 RPM Motors; LH & RH Counter Rotating Spindles; NC (Servo) controlled with automatic intervention that guarantees a perfect base for gluing. -- Anti-Adhesive:Automatic Spray Unit with: Glue release agent preventing glue from adhering to work piece's surfaces. -- Infrared Heating Lamp:Preheating workpiece edge to ensure best possible surface adhesion quality of edgebanding material. -- Edge Magazine: Automatic 2-coil/position magazine for processing coiled & strip edgebanding material in real-time. -- Pressure Section:Servo Controlled programmable pressure section with: (1) Large driven roller and (4) idle rollers.Gluing System w/Premelter: -- EVA (Hot Melt), quick premelting granulate with: Glue roller applicator to cover conventional edgebanding material. Workstations: -- End Trimming: Front & Rear Linear end trimmer with: Tilt Function for high speeds with (2) 0.8 kW (1.0 HP) - 12,000 RPM motors. The machine axis movement on linear tracks allows the achievement of very high processing speeds.The copying & tracing system guarantees optimal finish quality; also on high gloss edges with film. -- Flush/Bevel Trimming Unit:Top & Bottom flush or bevel trims with: (2) "Quick Change" 0.65 kW (0.8 HP) - 12,000 RPM motors. -- Fine Trimming Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors; (2) Servo motors for tool positioning (one for horizontal tool position, one for up/down tool position).Prepositioning of motors by pneumatic air cylinders while using a combination bevel/radius/flush insert knives.Absolute machining flexibility thanks to the full adjustment of the machine according to the required edge thickness. -- Corner Rounding Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors for front/back corner and upper & lower edge profiling.The controlled axis on the Corner Rounding unit supports the management of infinite machining settings. -- Profile Scraping Unit:Top/Bottom 2-axis NC programmable knife positioning (i.e. 2 - 3 mm radius) for PVC edges. -- Glue Scraping Unit: Flat, top/bottom, digital positioning indicators, pneumatically controlled for in/out position. -- Buffing Station: Top & Bottom buffing motors: 0.37 kW (0.

Biesse Levia 310-1350 Sander