Equipment For Sale

Northfield #4 Table Saw - In great working condition - Size: 4 - Serial: 62354 B - Northfield Special Heavy-Duty Motor: - Type: Arbor - HP: 7.5 - RPM: 3450 - Phase: 3 - Cycles: 60 - Code: L - Frame: J58 - Enclosure: TEFC - Winding: R & M - Serial: MS92250LV - Temp Rise: 55°C - Volts: 220 / 440 - Full Load Amps: 21 / 10.5 - Size information: - 1390 lbs. - 44" L x 36" W x 44" H - Weight & measurements are not inclusive of pallet (not shipping info) Call 800-459-2148 for more info.

NORTHFIELD - #4, ...Table SawSpecifications: -- 16" Dia. saw blade cap.; 7.5 HP - 3,450 RPM motor; 1" dia. arbor; 13/16" dado cap. with: Thin collar; blade tilts: 0° - 45°; 32" rip cap. with T-type fence.

1/2 and 3/4 yard grapples. Northshore grapples in comparrison to other manfactures are larger in size. There 1/2 yard grapple is same as 3/4 yard. Sizes available up to 2 yards.

6” width capacity 8” thickness capacity 30 hp main motor, 1.4 hp feed motor 3 hp blower motor…460 volt 3 phase 559 rpm blade speed digital oiling

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

NORTHTECH NT 400EL Double Head 16" PlanerHeavy Duty Chain Drive Series Double SurfacerSpecifications: --15 HP Top, 15 HP Bottom Head Motor -- Dual (6) Row Helical Cutterhead with four sided 15 x 15 x 2.5 mm Inserts -- 5,175 RPM solid steel cutterheads with Class 7 NSK bearings -- Cutterhead dimensions: 5"; dia. x 16"; long -- Operating decibel rating of 79 dbProduct Dimensions: -- Working thickness 10 - 155 mm (3/8"; - 6-1/2";) 8 mm min. on request -- 13"; Min. working length -- 16"; Maximum widthFeed System: -- 3 HP Feed motor -- Carpet feeding spike system with (644) spikes -- Feed speed 25 - 85 FPMFeatures: -- 1 HP Elevation motor -- Mechanical variable speed -- Digital control panel with 3 amp meters -- Chrome bed plate 0.01mm (0.004";) thick -- Passline at 32"; -- Amperage requirement: 230V / 115 AMPS, -- (2) 6"; Dust ports requiring 981 CFM @ each point of extraction -- Automatic lubricating system with low level shut off -- UL/CE Certified electrical components -- Includes operator’s manual and parts book -- Net weight: 5,990 Lbs -- Machine / Packed weight: 5,990 Lbs / 6,195 Lbs -- Machine/Packed dimensions (L x W x H): 98"; x 50"; x 70"; / 101"; x 46"; x 80"; -- One year parts warrantyNOTE: All machines are tested stateside prior to shipment providing trouble-free start-up.

NorthTech 18" Pop-Up Saw. 10hp Motor. #00872

6” x 24” capacity 2 sided knives on helical cutter head 534 hours in meter

Northtech Chop Saw

Northtech 12" Resaw Model NT-HBR12V Self contained hydraulic pack

Northtech horizontal band resaw, (2) blades, will cut up to a 12 x 12" cant, powered by (2) 20 HP 460 Volt 3 Phase motors, runs (2) 1 1/4" band blades, Excellent Condition, (new condition with less than 4 hours use). Owner is retiring. Ref# 119, Contact Amy (928) 723-9449

Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

Rigid one piece welded steel frame, with 10 HP direct drive spindle motor at 7,800 RPM, 1-1/4" x 4-1/2" stackable multi-cutter spindle to mill stile, rail & raised panel profiles. -- Stackable cutter spindle with push button indexing to significantly reduce set-up time as each station is preset; the change from one cutter to another is achieved via a select switch for each operation. -- Complete with: X - Y Sliding table w/pneumatic holddown. -- 2-way linear movement for straight or arch top doors up to 50" long. -- 5" Dust collection hood, and cutter shield. -- Includes: (1) Cathedral arch templates, (1) complete set of tools.

NORTHTECH NT-SRS12 Straight Line Rip Saw: 15 HP - 4,500 RPM Direct drive overhead mounted arbor motor, 1" dia. arbor, 8" - 12" max. blade cap., 3-3/8" max. depth of cut, 8" min. part length. Specifications: -- 18" Distance between saw and column. -- 57" L x 39" W table, table height 31-1/2", floor space required 1,200 x 1,600 mm (48" x 63").. -- 2 HP Variable feed drive, (5) feed speed from 59 - 137 FPM. -- Chain drive with automatic chain lubrication; feed chain track travels on hardened V-way guides. -- Top pressure system with spring loaded holddown rollers, dual anti-kickback devices. Equipped with & Features: -- Micro-adjust rip fence -- Laser Guide Line Light -- Digital auto chain oiler -- Full coverage guards -- 4" Dia. dust hood outlet -- Push button controls, and magnetic starters

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Northtech up-cut chop saw, 15 hp electric motor, 24" dia blade, air operated controls, excellent condition

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

NORTHTECH - NT-SL2000XL, ...Straight Line Rip SawSpecifications: -- 20 HP Direct Drive Straight Line Rip Saw. -- 2" Arbor. -- Distance from column to blade: 18 in. -- Saw blade size: 10" - 14". -- 3-1/8" Cutting capacity. -- Glue Line Saw. -- Feed Motor: 1.5 HP. -- Feed Speed: 20 - 105 FPM.

Northtech FR-200 Frame SawSpecifications: -- Saw capacity of 6" width x 8" vertical capacity. -- Minimum working 2"; high X 12"; long. -- Main drive motor to saw frame is 30HP 3PH, wired 460 --V servo drive system to feed works is 1/4HP 3PH, --Blower to saw frame rack for added cleaning value is 3HP 3PH, -- Body of frame saw is (2) sections allowing for fast access to the saw frame, -- Saw blade speed is fixed at 550RPM, -- Dust extraction requires min 3000 CFM and is arranged with (4) 5" ports, -- Blade size is standard with 500mm L x 40mm W x 0.9mm body in stellite or TCT tip,Equipped with & Features -- Digital electronic oiling system provides proper lubrication to the saw frame guides -- Vertical rail system which allows optimum cooling and long term durability, -- (4) guide blocks are thermo- censored to allow auto shut-off of machine should possible heat buildup occur.Machine dimensions 122"; L X 40"; WX, 79"; H weight 7100 lbs. Machine was new in 2007.