Equipment For Sale

2020 Peterson 5710D -6,680 hours -C-27 CAT -Fresh service -New teeth -Undercarriage at 80% -Drag chains and discharge belt still like new PRICE HAS BEEN REDUCED to 437,000 USD !!!!!!! get it while it lasts!!!!!

2002 Peterson 7400a Horizontal Grinder -End of summer 2022 we installed NEW -Cylinder packs and bearings -Both turbos -High pressure oil pump -Ecm -Injectors -All gaskets and orings -Oil pump -Twin disk clutch -Had the heads completely rebuilt -Radiator completely gone through -Rebuilt feed floor -Rebuilt mill -Mill bearings checked for clearance and passed -All belts and chains in good shape -Alot of extra screens and parts come with it. Some are brand new

2019 Peterson Pacific 2710D Track Horizontal Grinder, Caterpillar C-18 765 HP, Frame Hours 4,500.00, Caterpillar put in a new engine around 3,500 Hours, Dropped a Ring in the Engine, Has Platinum Engine Rebuilt, Undercarriage is 95%, Wireless Remote Control, Air Compressor, Ready for Work. Machine Weight: Approx. 68,100 lbs Width: 8' 2" Length: 40' 8" Height:11' 1" Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

1999 Peterson Pacific 5000G Chipper -1000 h.p. 3412e engine -8000 hrs since major overhaul -3 flail -Spare flail pump -Load adapters replaced within last 1000 hours -Fan pump replaced 1500 hrs ago,Also has had swing and boom pump replaced -New Ecm has less than 750 hrs -New muffler -New feed roll teeth -New heater and a/c -Spare clutch, Spare belts, Spare pins and Seal kits -Babbit or key knife system -Fleet maintained

New remote All outriggers intact and work. Two lower green wear plates worn but being replaced New radiator screen (pictured) will be installed.

Remote control

Peterson 4800 Flail Debarker Wireless remote controlled Reman engine Runs and operates good

1998 PETERSON PACIFIC 2400A WOOD GRINDER CAT 3406C ENGINE GOOD MILL GOOD FEED CHAINS LOTS OF NEW PARTS RUNS VERY WELL WORK READY FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTH DEFERRED PAYMENTS WITH GOOD CREDIT IN-HOUSE FINANCING FOR MOST CREDIT TYPES GRANITEHE.COM

2017 Peterson Pacific 4300 Whole Tree Chipper, Micro Chipper, New Rebuilt Cat C-18 Engine, 785 HP, Under 50 Hours, Frame Hours 10,500 Hours, Air Compressor on the machine, Ready to Chip Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2011 Peterson Pacific Horizontal Grinder Power Source: Diesel Engine Mfr: Cat Engine Model: C27 Horsepower: 1000 Has approximate 9050 hours

This machine is 100% redone. Completly rebuilt motor, new pumps, hoses, wiring harness. New knives and infeed chain

Machine recently had a New Crate Engine installed prior to fire and during the install the mill was completely reworked, rods,hammers, new wear plate, chains, chain head pulley This has sustained an engine fire which was contained in the engine compartment. Engine is not recoverable. This machine would be a great candidate for a Rebuild or an ideal Electric Conversation. A last resort would be to part out the machine.

JUST REBUILT - CALL FOR DETAILS CAT C27 ORIGINAL HOURS - 1050 HP - TIER 3 NO DEF TOO MANY NEW PARTS TO NAME REBUILT TROUGH, NEW PT CLUTCH, NEW PUMPS (ALL), NEW WIRING HARNESS, NEW DRAG CHAIN, FEED BED, ALL HOSES, GRATES, COMPRESSOR AND MORE.

Pettibone Loader Mdl 104A S/N 2619 with 5' Forks

Pettibone Wheel Loader Mdl 104A S/N 2095 5' Forks

Phelps chip blower and fan with duel loading pipes. Call 800-459-2148 for more info.

Phelps Chip Blower 42" Dia Fan Blade 54" Cage.

Phelps Chip Blower with 20HP Motor

Phelps 32" With Airlock & 30HP Motor