Equipment For Sale

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i61 WHIRLWIND 1000 L Upcut Saw Specifications: 2-3/16" x 8-1/4" Cap., 14" blade cap., 3,450 RPM, left-hand unit feeding from right-to-left, 5 HP BALDOR motor. Complete with: (5 - 90) Cycles/Min; magnetic starter with low voltage controls, air filter, regulator, coalescing filter, and 4" dust chute. NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Brand New Whirlwind blowers in stock, 8" -14" inlet, good selection, all with AR-400 steel and Dodge bearings, heavy duty built, call with your needs

Whirlwind Sawdust Blower 36" fan 8 paddle fan 18" inlet reduced down to 17" 16" outlet

Whirlwind Up Cut Saw with Infeed & Outfeed Rollers

1984 White Tri-Axle Log Trailer, 42' Trailer, Good Tires and Brakes, Ready for Work Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1984 White Tri-Axle Log Trailer, 42' Trailer, Good Tires and Brakes, Ready for Work Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1985 White Tri-Axle Log Trailer, 42' Long, Good Tires and Brakes, Ready for the Woods. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1992 White 42' Two Axle Log Trailer, Good Tires, Lights and Brakes, Ready for the Woods Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

Whitney 105 Planer 24" Planer Used daily in current shop.

Whitney 105 Planer 24" Planer Used daily in current shop.

wicker forks are on a 644G loader we are parting out . Good condition for information you can contact Gavin 601/394/7796 Tim 251/366/3237 Kameron 251/242/5493 located at 467 Saint Peter Street State Line MS 39362 ALL SALES ARE CASH, CASHIERS CHECK OR BANK TRANSFER.

2005 Wilkens Walking Floor Brand New Tarp

WILLIAMS - Hammer Mill: Half-round Type ConfigurationFeatures: -- 220 HP Main Drive Motor with Belt Drive; complete with Guard. -- 26"; x 12"; Input Opening. -- Powered Input Pull Rolls -- 4"; Main Shaft with Swing Hammers, approx. 3/8"; thickness -- Ratchet Lift Access Lid. -- Mounted on Steel Support Structure with Access Platform and Ladder -- Pneumatic Bottom Discharge with built-in Viewing Window in Ducting below the Hammermill (no fan included) -- Electrical Cabinet with Motor Starters -- NOTES: This machine was last utilized to break up virgin dried pulp for further processing. Already been removed from service – ready to load.

Williams 125 HP Hammermill 230/460 3-phase

Williams 125 CJS1 Hammermill

Williams Hammer Mill 40"w #C740

24” x 36” inlet 8” x 36” outlet 150 HP motor fan on outlet

24” x 36” inlet 8” x 36” outlet 150 HP motor fan on outlet

William & Hussey "W-7S" Moulding Shaper -- Specifications: 17-1/4"x 14" Table size, 2 HP main motor, 2-knife cutter head, 3,450 RPM spindle speed, 7" max. cutting height, 1/4" min. thickness 3/4" deep max cut.. Max moulding cap. 7" wide, max. planning cap. 7" wide. -- Complete with: Dust hood outlet, electrical disconnect, and mounted on fabricated steel stand w/casters, Multi-pass

Williams and Hussey 2007 W7-S model 206 planer/molder good condition Ser# 00452 Weight 250 ish Max thick 7”, Max width 7” Multi pass Baldor motor Powered infeed and out feed New std knives available at W/H for app 100/set Custom knives available from W/H