Equipment For Sale

CEMCO 2000 Wide Belt Drum Sander, Single Head. --Specifications: Lightly used. Only 2180 Hours. -- Belt Size is 37" X 75"; 20 HP main motor,.1.5" top roller plus 2- 5" bottom rollers. One steel 1 rubber covered. -- Thickness is from 0" - 6". No Platen. Variable speed feed. Emergency brake. good. 4-1/2" dust port. -- Note: This machine was replaced 12 years ago with a triple head Cemco. Stored in a dry warehouse since then. Ran well until we unplugged it. All Cemco equipment is of commercial quality. This sander is a workhorse.

Cemco 2000 Wide Belt Fair/good condition. It starts and runs until we unplugged it 12 years ago Belt size 37 x 75 2004 Single head 1- 5” roller top, 2 - 5” rollers bottom, 1 rubber covered, 1 steel. No platen Thickness ¼” – 6” 2179 hours on machine 230 V, 60 CY, 3 PH Variable speed feed 20 HP motor Emergency Brake

CEMCO 3 Head Industrial Sander. Running when removed from location.

CEMCO SBV-120 Vertical Boring MachineSpecifications: -- 113" x 22" boring area Capacity, (14) 1.5 HP - 1,800 RPM motors driving (14) spindles, on/off switch controls for all motors -- Spindle nose with chuck 5/65" - 1/2" capacity -- 121" x 30.5" table size, (4) Spring loaded hold downs, -- 6" Spindle stroke adjustment with min. of 4" to max. of 10" between spindle nose and tabletop. -- Spindle assemblies advance hydraulically at 0 - 30 strokes/Min with single or continuous stroke -- 2 HP hydraulic feed pump w/variable speed control.Also included: -- 4 CHIP BLOW OFFS WITH INDIVIDUAL ON/OFF POSITIONS -- INSTRUCTION MANUAL/PARTS LIST -- DRILLING SAFETY GUARDS -- EMERGENGY STOP CABLE AND EMERGENCY STOP BUTTONFLOOR SPACE FOOT PRINT: 48: X 121"

- Width capacity 53”. Drum, Drum, Combination Head (see sander specs - Head 1: Rubber covered contact roll, 10” dia, 65 shore adjustable with dial - Head 2: Rubber covered contact roll, 10” dia, 65 shore adjustable w/dial - Head 3: Combination head, (2) 5-1/2” finishing drums w/platen - 440 V, 60 cy, 3 Phase - Year 2000, Good Condition - Warehoused after plant shut down factory in 2013 - Have manuals /spec sheets - Machine weighs app 6000#’s. - Buyer must pay for riggers to load onto truck. (our forklifts can’t pick it up)

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,Equipped With:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single cycle & continuous automatic modes;2 HP hydraulic feed pump, 12-gal. hydraulic pump system;Note: Riggers are required for loading

CENTAURO AG-125 Tool Grinding Machine for V-Type Gouges. -- Tabletop design saves space. -- Works with most sizes of V-gouges. -- Optional standing base $414.00. -- Diamond stone cutting wheels, ordered separately, price $636.00 each. -- Please specify the required voltage and lathe model when ordering wheels.

CENTAURO T5-1600 Hydraulic Copy Lathe with (2) top plunging knives; Specifications: -- 63" (1,600 mm) Max. between centers, 4/5.5 HP main motor, two speed selector switch, 900 - 1,500 - 1,800 - 2,250 - 3,000 and 4,500 RPM spindle speeds. -- 1 HP Hydraulic power pack for variable speed carriage 0 - 19 FPM carriage; return speed 24 FPM, hydraulic tailstock with Pressure Reducing Valve (PRV) for fine control of pressure, especially helpful for small and/or slender turnings. Equipped with: -- (2) Independent copying units, (1) for roughing and (1) for finish cutting. 1st, 2nd pass & auto feature with 2nd pass active it will cut the pattern 2 times automatically and sequence the tools between cuts. -- Revolving steady rest, max. dia. 140/100 mm square ( 5.5"/3.9"), and for max. dia. 90/65 mm max. square billet size. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. Includes: -- (2) rear-top plunging slides manually operated with knives for making dowel ends; 45/26 mm drive center for headstock and 12 mm center for tailstock, (2) V-type gouges with 0.6 & 3.5 mm cut radii.Features: Centauro AG-125 Knife Sharpener.NOTE: Ex-Factory handles import/export to just about any country in the world.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with two copier heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and revolving steady rest attachment; 3-1/2" max. square part size with revolving steady rest, unit, 5.8" stroke of copying unit. 19-5/8" max. length for manual turning. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. -- Includes: Drive center, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center. -- Note this machine has no top Back Knife for plunging with form tool. -- Machine manual included.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with (2) Copier Heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and attachment for revolving steady rest; 3-1/2" max. square part size with revolving steady rest, 5" max. with copying unit, 5.8" stroke of copying unit. -- Capacity: 19-5/8" Max. length for manual turning. 9.8" (250 mm) Max copy dia., 6.8" (175 mm) max. square section without steady rest. -- Includes: Drive center with, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center.Note this machine has no top Back Knife for plunging with a form tool.

CENTAURO TC-1200 Copy Lathe;47-1/4" Max. between centers. -- 4-3/4" Height of centers over bed. -- Max. copy dia. 6" (4-1/8"). -- Max. dia. permitted by traveling steady 3-1/2" (2-1/2"). -- 4 HP main motor, 900 - 1,500 - 2,200 & 3,540 RPM spindle speeds. -- 1 HP hydraulic variable speed carriage with tool post and revolving steady rest. -- (2) Independent gouges working in conjunction with the traveling steady rest. -- Variable speed hydraulic saddle movement. Standard Equipment & Specs: -- Drive center with (2) interchangeable heads 1" and 1-3/4". -- Tailstock revolving center 1/2". -- Traveling steady rest max. 3-1/2" (square 2-1/2" x 2-1/2") with reduction bushing. -- (2) Vertical Tantung gouges, radius 1.2 mm and (1) precutting tool. -- Work-piece centering device. -- Tool support rest for hand turning. -- (2) Dust extraction ports 4" dia. -- Motor protection switch. -- Emergency push button. -- Front sliding safety guard. -- Standard: Service tool kit and Abrasive stone for cutting edge dressing.

Extremely well-built Edge Sander with 5 HP - 1,200 RPM TEFC Motor. -- (2) 11" x 60" Cast iron platens. -- 10" x 172" Abrasive belt size. -- 0.5 HP oscillation motor to produce (150) oscillations/Min with 1/2" movement. -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table. -- All tables with 30° tilt up & 45° down. -- 5" Vertical table travel, 5" lateral side table travel and 4-1/2" lateral end table travel. -- Convenient hand wheel adjustment. -- Large 10" dia. x 10-1/2" face direct drive pulley with 4-1/2" dia. x 10-1/2" idle pulley for a huge sanding surface. -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

formation BUCKET NEEDS WORK! MOLDBOARD HAS MULTIPLE CRACKS AND WORN THROUGH AREAS, WORN SIDES. SLIGHT DENTS IN BOTTOM OF BUCKET TUB. Fits On Category TRACK EXCAVATORS. Fits On Model 385 C L, 385 C L (Reach), 390 D, 390 D L, 390 F L, 390 F L Reach, 395

Nice CF Nielson BP5500 Press. The plant shut down in 2014. The machine was run again for a test in 2016 and everything was in good working condition. They have the dies and pistons to make round and octogonal logs. - Briquetting press CF Nielsen BP5500 - Dies to make 3’’ round logs and 2½’’ octogonal logs - Lignin dosing system - Water pump to add water if material too dry - Home-made automatic speed adjustment with encoder. - Briquette breaker from CF Nielsen at the end of the cooling line - Home-made flying saw with lenght asjustment at the end of the cooling line too with capability to switch from the saw to the breaker. - Can run up to 1200kg (even 1400kg I think) per hour depending on material and briquette shape - Cooling line can be opened to make pucks also. - 575V AC motors - Installed in 2008 - 10,865 hours

CFORM Edger/Rip Saw - model CKM160 This machine was purchased new and installed the beginning of 2023. It has less than 20 hours. The seller changed applications. Machine is ready to load. Photos coming! Manufacturer information: Double Edgeing & Slicing Cutter the value of lumber with clean edges can often exceed the value of rough-cut boards. In one pass, this Twin Blade Board Edger takes boards fresh off the mill and turns them into clean, square edged lumber. This edger is easy to use, with one fixed blade and one moveable blade that adjusts with a manual dial. Easily select the precise size of lumber you need. Lower the perimeter fence when you need to edge only one side of a board. Features: Movable finger iron platers for safe guidance and protection. Maximum 15 raws circular saws, adjustable distances. Hydraulic upper roller pressure and movable cyclinders. Maximum cutting height (inch)6 5/16?, 4 11/16?

Challenger Grinder with 10' Infeed Steel Belt, On Board Hydraulics.

With a 12' infeed. 125 hp electric motor, low hour machine, makes nice mulch.

Challenger Grinder as pictured

This grinder was removed from service in good working condition. It is ready to load/currently in storage 200 HP Main Motor Cutters 117 F-Cutters Screen (4 ) 22" Diameter Wide with 1-1/2" Holes The width is 51” and the height is 17” (infeed opening)

Challenger Model Series 200 to 1000 Slow Speed Wood Grinder w/30hp 480V Motor. Infeed measures 5' Long x 2' Wide x 4' Deep. Footprint measures 7' Tall x 4' Wide x 6' Wide.