BioMass Equipment For Sale

Announcing two brand new lightweight, fixed tooth brush cutter mowing attachments from Torrent Mulchers - the EX28RPM & EX30RPM. Designed to handle anything from mowing grass to whole tree removal, these powerful lightweight mulchers will attach to almost any carrier. EX30 RPM TECHNICAL SPECIFICATIONS Operating weight - (Standard) 700 lb/313 Kg Cutting width - 30 inches Rotational speed - 3200 RPM (maximum) Excavator power requirement - 30 Hp or 22 Kw (minimum) Excavator weight range - 6 to 12 tonne Cutter type - fixed spherical or fixed beaver Cutter quantity - 18 Drive type - direct Power transmission type - hydraulic fluid power Hydraulic motor type - fixed axial piston Maximum hydraulic system pressure - 5000 psi/345 bar (maximum continuous) Hydraulic oil flow requirement - 18 usgpm/68 lpm (minimum)

1988 Trelan Model 18 Whole Tree Chipper Equipped with Detroit 518 Diesel Engine, Engine Hours Unknown, New Drive Chain and New Belt, New Tire, No Separator Ready for the Woods... Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2006 Trelan 23 -No blow by and doesn't use oil -New hood jack -New cylinder -10 sets of new blades -Extra set of belts -Disk pockets are in good shape

1989 Trelan 23 Chipper -9000 frame hours -Rebuilt C-27 CAT with 200 hours on engine -New tires -New outrigger piston -Rewired corded remote -New wireless remote -New hoses -New intakes -New bearings in the PTO -Engine Preheater -New Auto-feed system NEEDS PAINT BUT WILL GO STRAIGHT TO WORK!!!

2005 Trelan 23RC Whole Tree Chipper, 3 knife, Cat V12 with 5,000 hours, New clutch and disk bearings. Works as it should. Approximately 5k hours makes a beautiful chip. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

UMP BP500A Briquette Press New System - Ready to ship!

UMP - BP 450 A: 450 kG/Hr Briquette PressSpecifications: -- Cap. 450 kG/Hr (992 Lbs). -- Max. pressure: 1,700 kG/cbm (24,175 PSI). -- Max. chip moisture content: 15%. -- Max. chip size: 15 mm (0.59"). -- Wood shaving to briquette ratio: 10 to 1 (using mahogany). -- Briquette configuration: Rectangular. -- Briquette length: 40 - 105 mm (1.57" - 4.13"); Briquette width 150 mm (5.91"); Briquette height: 60 mm (2.36"). -- Briquette heat energy: 4,200 kCal/kG (7,558 BTU/Lbs). -- Hopper size: 31"; x 36"; x 36"; with: 1-Side sloping so cutaway from cube of 18"; x 36";; mounting flange at top allows additional capacity to be added.Equipped with: -- Automatic material density adjustment. -- Automatic hopper shutoff. -- SIEMENS PLC Control.

Belly Conveyor 9' long 30" wide Includes 3 phase electric motor and switch box Ready to load on truck

Bark Auger 16" x 24' 12" auger with hydraulic drive

STI - AP 980 M (could be an Automation Plus) Bagging System With Bin and Bag Flattener to Pallet Stacking Stand

Double Bay Leveling Auger System

Dust Collection Cyclone and Frame

twin-screw 36" hollow screw auger conveyor, 6ft wide screw conveyor, dual 36 inch screw conveyor, double 36" x 27ft hollow screw conveyor, REPAINTED LIGHT ORANGE, Dual 36” shaftless hollow screw auger conveyor, conveyor is soon to be completely repainted - more photos to come, inside length 27 feet 6 inches, inside width 6 feet 2 inches, overall outside length of conveyor 30ft 10 inches, conveyor trough is 50 inches deep, overall outside with of conveyor trough 6ft 9 inches – overall outside width can be reduced to 8ft wide by unbolting both motors and chain guards during shipping, lube oil can be added inside chain guards so sprockets and chain can be lubed by the oil bath – site glass and plugs are attached to both chain guards, flighting spacing 24 inches, flighting thickness 1 inch, flighting width 7 inches, 2 Falk gearboxes with 25HP motors – both 25 HP motors & gearboxes have been removed from conveyor and have had the bearings replace in motors, and the Falk gearboxes have been serviced/oil changed by a independent motor repair shop and test ran with video footage by independent electric motor shop, currently both gearboxes and motor are stored inside our temperature-controlled warehouse, weight 25,000 lbs, overall outside width of conveyor with motors attached is 13ft 6inches, call for more details and a delivered price to your location, price includes loading, Videos of conveyor running: https://youtube.com/shorts/n_lBAIgTors front complete https://youtube.com/shorts/3RvvkOw8nuc Back complete https://youtube.com/shorts/hDPVHPYe6Dc complete overall NOT running https://youtu.be/u1FKcccdt0Y front single to single

New 36" wide x 20' long Heavy Duty Inclined Feed Conveyor 12" Sides Cleated belt with 2" high cleats on 24" centers 6" diameter feed roller with bearings in a heavy duty slide frame allowing adjustment for belt alignment 8" diameter drive roll Driven by a 2 HP motor/gearbox with a chain /sprocket system. Bottom of the conveyor is app 6" off the floor. The exit height (distance from the floor to the bottom of the drive roller) is app 135" There is a hopper at the bottom of the conveyor that is 60" wide Distance from the floor to the top of the hopper is app 42". This height is ideal for use with a box dumper All legs have a height adjustment of 12". Motor will handle a VSD if wanted. 460V/3PH/60Hz. Note: The front legs are set back 80" which allows the conveyor to clear a Vecoplan Shredder and drop the material into the hopper

Inclined Cleated Conveyor 24' Long 24" Width 3" Cleats 2 HP Approx 10'-12' Drop Height Came Out Running

Incline Conveyor 23' long 24" wide Includes 3 phase electric motor and switch box Ready to load on truck

Infeed Conveyor 31' long 30" wide Includes 3 phase electric motor and switch box Ready to load on truck

MLS Number 11202465 Straight Wall Storage Bins 2- 17-unit straight wall bins ( for hog fuel) Were in operation for less than 2 weeks Voltage 575 Drawing available Price includes dismantling and loading Two weeks to dismantle and load

Japanese Boiler 150HP

Japanese Boiler 150HP