Mobile Wood Chippers For Sale

2019 Morbark 1621 15" Capacity Chipper, PSI 145HP Gas Engine, Hydraulic Winch, Good Running, One Owner Trade In Machine.

MORBARK 20 CHIPPER REBUILT ENGINE WITH 4 HRS ON IT NEW BRAKES NEW WEAR PLATES RUNS AND OPERATES AS IT SHOULD 1 OWNER MACHINE FINANCING AVAILABLE WITH NO MONEY DOWN GRANITEHE.COM

(2) Available Morbark Series 2000 Stac Trac

ONE OWNER, LONG TIME CHIPPING CONTRACTOR REBUILT CAT C27 ENGINE, NEW CLUTCH, RECENT DRUM, FEED DECK, FEED CHAIN, CAN FILL TRAILER IN 11 MINUTES. MUST SEE. WELL MAINTINED, STILL RUNNING IN PRODUCTION STILL RUNNING, HOURS WILL GO UP

Includes Lots of Spare Parts Tidy, Well Taken Care of Machine, Woods Ready.

2002 MORBARK 30/36 TREE CHIPPER METER READS 2,738 HOURS GOOD DRUM MORLIFT 150 LOADER CAB GOOD TIRES GOOD CONDITION FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

1998 MORBARK 30/36 TREE CHIPPER METER READS 2,738 HRS GOOD DRUM RUNS GOOD GOOD FEED CHAIN GOOD CONDITION ON CONSIGNMENT LOCATED IN WRENTHAM MASS FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

Mechanically very good Morbark 22RXL Chipper with low original hours (approximately 7500 - manual meter inop). Fitted with CAT 3412 Engine at 800hp, Morbark 75" Disc (4-knife), Morlift 1000 loader, Manual clutch. Runs and chips well with typical wear for age and hours.

2014 Peterson 4310B -7200 hours -C18 755 H.P -New Belts -New Anvil -Comes with remote -Extra knives and counter knives Ready to work !!!!!

2010 PETERSON 4300B DRUM CHIPPER REBUILT CAT C18 765HP ENGINE TWIN TURBO NEW CLUTCH NEW BELTS NEW ROLLERS REBUILT HYDRAULIC MOTORS CHIPPER IS IN VERY GOOD CONDITION FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

Good condition, Woods ready.

3 flail chipper with 3412 cat engine, Prentice 180D picker, tri-axle, up-graded 3 flail to the H Model orientation. Engine rebuilt with a refurbished cat block, 950 hours since rebuilt. Total reversing flail from cab. Flail speed set mechanically using pump stroke limiters. 65" shiv, hydraulic system with air clutch, babbit knives. Twin disc clutch rebuilt 2000 hours ago. Was used to chip hardwood with a bark content of under 3%. Paddles and anvil replaced in the last 2000 hours. Frame has an estimated 13,000 hours. Well maintained and in good working condition.

2019 Peterson 5000H Chipper -9500 frame hours -Complete Cat rebuild done at 6800 hours -4 flail -Loader -Tons of service receipts and very clean machine Videos upon request

2008 Peterson 5900 Tree Chipper -10560 hours -4000 on complete rebuild -Works as it should -Tires good -Two boxes of key knives

2011 Peterson Pacific Horizontal Grinder Power Source: Diesel Engine Mfr: Cat Engine Model: C27 Horsepower: 1000 Has approximate 9050 hours

Precision Husky 23 Chipper Needs engine Has Cummins KT19 650HP

1996 Precision Whole Tree Chipper 21" Capacity 700 HP Cummins KTA Twin Turbo Needs Clutch AC Heat Good Feed Rollers Disc Wheel Completely Rebuilt New Anvil New Wire Plate Husky 235 Loader 52" Rotobec Grapple PRICE REDUCED

2006 Trelan 23 -No blow by and doesn't use oil -New hood jack -New cylinder -10 sets of new blades -Extra set of belts -Disk pockets are in good shape

1989 Trelan 23 Chipper -9000 frame hours -Rebuilt C-27 CAT with 200 hours on engine -New tires -New outrigger piston -Rewired corded remote -New wireless remote -New hoses -New intakes -New bearings in the PTO -Engine Preheater -New Auto-feed system NEEDS PAINT BUT WILL GO STRAIGHT TO WORK!!!

One Owner, C27 Engine, Call For Details.