Equipment For Sale

CEFLA TNS 6000 Rubber Belt Transfer Conveyor 236"; long x 74 1/4"; wide (66"; wide belt) -- 3PH motor --Adjustable height feet

CEFLA PSP6 Six (6) Gun Automatic Molding SprayerThe machine was purchased to spray PVC extrusions but the client changed his requirements, so the machine was taken from service. The machine has less than 1 year of light use and is in very good condition.As with all sprayers, it will require some cleaning and we recommend replacing the fluid lines with new ones. The machine has two (2) Spray zones with (3) guns in each. Each zone has a separate circuit. This machine is manufactured in the USA at the CEFLA facility in Charlotte, NC. Specifications: -- Two (2) Circuits Three (3) plus Three (3) or Six (6) on a single circuit -- ATEX Drive Motor, Inverter Controlled -- In / Outfeed Belts with Rollers with protection sleeves inside the spray booth -- ATEX-rated sensor-controlled guy triggers, individual on/off for all guns with individual manual test triggers -- Manual Atomization Controls -- ATEX-rated door safety switches -- Control Panel with Color Touch Screen -- One (1) 2000 CFM Exhaust, Explosion Proof -- Stainless Steel internal construction -- Pull out the overspray collection cart with removable Teflon-coated collection trays for ease of cleanup and the possibility of recuperation of coating material -- Filter cabinet on the back of the machine with easily replaceable mesh filters.

Cefla Prima Sprayer Infeed & Outfeed Conveyors Pumps & Guns Already disconnected and ready to load!

Cefla Prima Sprayer Low usage Ready to ship!

Complete Finishing Spray line 1300mm Wide with the following pieces. In feed Conveyor Sorbini panel cleaner Cefla UNO spray multiple circuits Conveyor Cefla 3 section vertical oven with boiler Out-feed conveyor all pumps and Guns

Cefla Roctre/D Reciprocating 2 Head Spray Machine 1600 mm wide spray area.

Cefla Rotostain 2000

Cefla Roctre/D Reciprocating 2 Head Spray Machine 1600 mm wide spray area.

CEHISA - PRO-9, ...Edgebander Single-Phase Electrical!Single-sided Edgebander with: End trim; top/bottom trimming; scraping; buffing.Specifications: -- 0.4 - 3 mm Edge thickness cap., -- Teflon coated glue pot system. -- Automatic magazine for strip & coil feed; Heavy-Duty guillotine for up to 3 mm thick PVC. -- (2) roll pressure zone with (1) motorized and (1) idle roller. Workstations: -- Double-motor end trim station; 0.33 HP - 12,000 RPM ea. motor. -- Top & bottom flush/bevel trim; bevels 0° - 20°; 0.45 HP ea. motor. -- Top & bottom PVC profile scraper; up to 3 mm radius. -- Last Station: Top & bottom buffing unit; 3/4 HP motors. -- Electronic braking on trim motors; digital readout on top/bottom trim. -- Feed speed: 33 FPM & 1 HP feed drive. -- Sound enclosure. -- Outboard panel support. -- Frequency converter. -- Digital readouts for trimmer adjustments. -- Sound enclosure.

CEHISA PRO 10 .EDGEBANDER (W/PREMILL): -- Features: Pre-milling Station with: 2 x 1.5 kW (2.0 HP) 12,000 RPM motors; standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System: 10 - 15 Min. heat up time, auto-temperature drop. Glue Tank is coated with nonstick material, quick change mechanism for easy maintenance and/or color change. -- Pressure Section: (1) Large dia. driven and (2) idle rollers. Digital readout and pneumatic positioning selectable from controller touchscreen. -- Edgebanding Workstations. End Trimming Station: Double motor front & rear, 2 x 0.35 kW (0.5 HP) - 12,000 RPM. -- Edge Trimming Station: Top & bottom flush/bevel/radius trimming, (2) 0.35 kW (0.5 HP) - 12,000 RPM motors, tiltable 0° - 20°, pneumatic exclusion from operator panel. -- Profile Scraping Unit: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper: To remove potential glue squeeze out. -- Buffing Unit: Top/Bottom, (2) 0.12 kW (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Controller: "Unitronics V350" Controller with color touchscreen, memory up to (20) programs. -- Equipped with: Feed Speed: 9 & 14 MPM (29 & 46 FPM). -- Power hold-down beam, workpiece support outrigger, safety & sound enclosure. -- Included Options:RIEPE non-stick Spray System. -- Actual Model is: CEHISA PRO 10

CEHISA PRO-12 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Features: Pre-Milling Station with:2 x 1.5 Kw (2.0 HP) 12,000 RPM motors, standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Spray agent unit for top and bottom with (2) sprayer and (2) reservoir -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System, MR-5:10 - 15 min. heat-up time, auto temperature drop. Glue Tank is coated with nonstick material, quick-change mechanism for easy maintenance and/or color change. -- Pressure Section:(1) Large dia. driven and (2) idle rollers. Digital read-out and pneumatic positioning selectable from controller touch screen.Edgebanding Workstations: -- End Trimming Station, V-7: Double motor front & rear, 2 x 0.35 Kw (0.5 HP) - 12,000 RPM. -- Edge Trimming Station, BC-5: Top & bottom flush/bevel/radius trimming, 2 x 0.55 Kw (0.75 HP) - 12,000 RPM, tiltable 0° - 10°, pneumatic exclusion from operator panel. -- Corner Rounding Unit, FD-50: To process overhanging edges and trimming around the leading & trailing edge, 1 x 0.27 Kw (0.36 HP). -- Profile Scraping Unit, R-8: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper, RR-7: To remove potential glue squeeze-out. -- Buffing Unit, PC-9: with spry mist unit top/bottom Top/Bottom, 2 x 0.12 Kw (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Operator Interface:PLC Microprocessor control with color touch screen, memory up to 20 programs.Equipped With:Feed Speed, 9 - 14 MPM (29' to 45 FPM), -- Power hold-down beam, work-piece support outrigger, safety & sound enclosure. Included Options:Riepe, non-stick spray system. -- Nesting Tracer Shoes for top/bottom trimmers

(14) spindles with 1-1/2 hp motors on each. On/off switch for each motor. chucks adjust to grip up to 1/2” bit stroke adjustable from 4” to 10” 121” x 39-1/2” table with (4) hold downs Adjustable speed hydraulic feed 230 volt 3 phase

CEMCO - 4000, ...2-Head Wide Belt Sander38" Width cap. - Drum, Platen configuration.Head Configuration:1st Head: 40 HP -1,780 RPM rubber contact drum head.2nd Head: 30 HP - 1,775 RPM platen style head.Specifications: -- 3 HP 230/460/60/3 Feed motor with TOSHIBA VFD controls. -- 15 - 60 FPM Conveyor feed speed . -- 30 HP - 3,525 RPM Vacuum blower. -- Vacuum type rubber conveyor feed belt. -- Push button controls and amp meters. -- Electric ProScale digital thickness readout. -- YASKAWA Varispeed F7.Equipped with & Features: -- VFD abrasive belt drive system. -- Outfeed workpiece dust cleaning enclosure.Includes: Replacement abrasive belts and belt racks.

CEMCO - UF-1137SE, ...Single Head Wide Belt Sander37" Width cap.; combination sanding head.Head Configuration:5-1/2" Rubber covered contact roller andIndependently adjustable 3-1/2" polishing platen.20 HP Main motor.36" x 75" Abrasive belt size; electric eye tracking.1 HP Variable speed feed, 15 - 60 FPM.Equipped with & Features:0" - 6" Manual part thickness opening of conveyor bed with:(4) 5-Ton lifting jacks.Double infeed & outfeed rubber covered holddown rollers.26" Infeed & 20" outfeed.Air disc brakes on sanding head.Load meter & push button magnetic starter.

- Width capacity 53”. Drum, Drum, Combination Head (see sander specs - Head 1: Rubber covered contact roll, 10” dia, 65 shore adjustable with dial - Head 2: Rubber covered contact roll, 10” dia, 65 shore adjustable w/dial - Head 3: Combination head, (2) 5-1/2” finishing drums w/platen - 440 V, 60 cy, 3 Phase - Year 2000, Good Condition - Warehoused after plant shut down factory in 2013 - Have manuals /spec sheets - Machine weighs app 6000#’s. - Buyer must pay for riggers to load onto truck. (our forklifts can’t pick it up)

CEMCO ‘SUPER HEAVY-DUTY’ SANDER 3 Head Sander with 3 Drums and an Extra Drum. Specs: Drum 1 - Hard Rubber Sands lumber, surface particle board, or MBK Takes 4-5/1000ths of surface w/ 80 Drum 2 - 65 lb, Soft - Custom For hardwood / veneers grip 100-120 grit #3 Hardware Takes 4/5000ths off Drum 3 - Smoothing Bar that is 4" wide. Contact is about 4" Takes 2 – 3/1000ths off - Comes with Spare Smoothing Bar - Drum 1 @ 75 HP and Drum 2 @ 50 HP motors can run @ 100 feet per minute - Was run at about 65 - Sealed Bearings - McGuire Bearings has them if needed - In & Out “Free Wheels” Belt Call 800-459-2148 for more info.

CEMCO SBV-120 Vertical Boring MachineSpecifications: -- 113" x 22" boring area Capacity, (14) 1.5 HP - 1,800 RPM motors driving (14) spindles, on/off switch controls for all motors -- Spindle nose with chuck 5/65" - 1/2" capacity -- 121" x 30.5" table size, (4) Spring loaded hold downs, -- 6" Spindle stroke adjustment with min. of 4" to max. of 10" between spindle nose and tabletop. -- Spindle assemblies advance hydraulically at 0 - 30 strokes/Min with single or continuous stroke -- 2 HP hydraulic feed pump w/variable speed control.Also included: -- 4 CHIP BLOW OFFS WITH INDIVIDUAL ON/OFF POSITIONS -- INSTRUCTION MANUAL/PARTS LIST -- DRILLING SAFETY GUARDS -- EMERGENGY STOP CABLE AND EMERGENCY STOP BUTTONFLOOR SPACE FOOT PRINT: 48: X 121"

CEMCO - URF-3352, ...3-Head Wide Belt Sander.53" Width cap. Drum, Drum Combination Head.Head Configuration:1st Head: Rubber-covered contact roll, 10" dia., 65 shores (to be verified), adjustable with a dial indicator, 50 HP motor.2nd Head: Rubber-covered contact roll, 10" dia., 65 shores (to be verified), adjustable with a dial indicator, 40 HP motor.3rd Head: Combination Head, (2) 5-1/2" finishing Drums & Platen.4th Station: Panel Brush.Specifications: -- 6" Max. working thickness. -- 1 HP Variable speed feed. -- 53" x 75" Abrasive belt size. -- Power raise & lower of feed bed. -- Numerical digital readout of thickness. -- Spring-loaded holddown rollers through machine. -- 36" Infeed table, 30" outfeed table; feed speeds from 5 - 60 FPM, 3 HP inverter. -- Load meters. -- (2) 8" Dia. dust outlets. Equipped with & Features: -- Belt Tracking (Electric Eye). -- Constant Pass-Line machine.Some spec's need to be verified.

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,Equipped With:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single cycle & continuous automatic modes;2 HP hydraulic feed pump, 12-gal. hydraulic pump system;Note: Riggers are required for loading

CEMCO 3 Head Industrial Sander. Running when removed from location.