Equipment For Sale

OAKLEY H-5 Double Sided Edge Sander. -- General Specs: With 7.5 HP -1,800 RPM TEFC motor; (2) 8-1/2" x 57-1/2" Cast Iron platens; 8" x 164" abrasive belt, 4,680 FPM belt speed. -- Equipped with: One 11" x 62" Cast iron side table on one side and (1) 19" x 64" cast table on the other side, (1) cast iron radius tilting end table, end table tilts 0 ° - 45°; 6" vertical table travel w/hand wheel adjustment. -- Features: Rubber covered direct drive pulley and idler pulley,Complete with: Magnetic starter with overload protection, (8) dead head radius ends with graphite covering, and (1) steel covered spare head roll.

Oakley Edge Sander

OGAM PO/M Straight Line Rip Saw;Specifications: -- 20 HP Main motor. -- 24"; throat capacity. -- Max. cutting height: with 12" blade 3", with 16" blade 4". -- Min. diameter of circular saw blades: 8". -- Max. dia. of circular saw blades: 16". -- Min. length of working pieces: 10". -- Variable feed speed from 50 -154 Ft./minute. -- Feeding belt width: 11". -- Spindle Speed: 4,500 RPM. -- 36"; x 60"; table.Equipped with & Features: -- Fence and rail system with one stop. -- Infeed table row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Top row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Split hold down steel smooth roller around blade. -- Split hold down steel smooth roller around blade. -- Steel smooth top hold down roller. -- Chain is in excellent condition!

OGAM MODEL PO-340 DIP CHAIN GANG RIPSAW ( THis is a Parts machine only )Specifications: -- 60 HP arbor motor, dip chain feed with overhead arbor, 13-3/8" (340 mm) max. rip cap. (between saw blades), 12-5/8" chain width. -- 9-13/16" Mn. to 13-7/8" max. blade dia., 4-3/4" max. depth of cut (manual raise and lower of the spindle), 70 mm dia. arbor runs @ 4,200 RPM; min. board length 19-3/4" (without short stock feed plate-see photo). -- Variable speed belted feed motor 20 to 100 FPM (approximate).Note From Seller: Ogam Gang Rip Saw. 60 HP motor 230/460. I don’t know much about this machine. Bought it used but haven’t been able to hook it up due to our current electrical service. The person I bought it from says it ran well when taken out of service. Can load on a truck.

OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGAM Gang Rip 30HP Motor w/electrical still Hooked Up, Model PO 195, S/N 15149

There are (5) saws available that range in age from: - 2006 (2) - SOLD - 2007 - SOLD - 2011 - One saw available

Ogden SL3660 RFS

30 brand new Oleson 10" double cut band blades. Entire lot for $20,000.00. Individual blade $1,175.00. Buyer pays for shipping. Call 800-459-2148 for more info.

OLIVER 4045 12" PROFESSIONAL TABLE SAW, with 36" FenceHeavy-duty cast iron table precision ground for accuracy; rugged machine frame construction provides maximum stability and reduced vibration.Specifications: -- 12" Blade capacity and 0° - 45° tilting arbor with digital read-out. -- 7.5 HP Motor at 3,450 RPM. -- Complete with: 52" rip fence capacity that will handle most of your work. -- 48" x 52" Cast iron table. -- Blade guard, miter gauge, push-button controls. -- Parts list & operation manual.

OLIVER 15" Planer with Helical Cutterhead - 10014, 3 HP (Single Phase)Unique design allows motor and cutter head to move in unison.Specifications: -- Auto-depth lock features twin nitrogen cylinders virtually eliminates snipping. -- Helical cutter head with premium carbide inserts. -- 4-Sided cutting inserts are indexed and easy to replace. -- Heavy cast iron construction including extension wings. -- Table and extensions wings are precision ground for smooth stock feeding. -- Table is fixed allowing easy use of auxiliary stock support. -- Wixey digital read-out allows precise thickness settings. -- Large handwheel and support struts allow easy height adjustment. -- Four-post design ensures head alignment regardless of stock thickness. -- Two-speed feed gearbox for better cuts, Oil bath gear lubrication for years of performance.Complete with: -- 4"; Port allows excellent dust management. -- Built-in mobile base allows easy movement in the shop. -- Magnetic switch for added protection and safety.

Oliver 36" Band Resaw

OLIVER 4470 25" Straight Knife Planer Full 24" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through the 4-knife standard cutter head, this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor. --OPTIONAL EQUIPMENT: Byrd Shelix Cutterhead (ADD $2,400)

OLIVER 4470 25" Shelix Cutterhead Planer; 10 HP motor Single Phase, or 15 HP 3-Phase motor. Full 25" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through , Byrd Shelix Cutterhead this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor.

OLIVER 4455 22" Straight Knife Planer, 5 HP single phase or 10 HP, 3-Ph.The OLIVER "4455" Planer has a super-wide capacity, it'll handle stock up to 22" wide, and takes up to 3/16" off in a single pass.Specifications: -- 4-Knife HSS straight knife cutter head. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on an uneven stock, coupled with a Driven Outfeed Roller to keep your stock moving smoothly. -- Add (2) feed speeds for extra quality, a Digital Thickness Guage for quick reference, and a powerful 10 HP motor. -- Max depth of cut 3/16" min part length 10"; Max work pc 22" w x 9" Thickness.

22"; Planer with Byrd Shelix Cutterhead - 4455B, 7.5 HP shingle phase or 10 HP, 3-phBYRD Shelix carbide inserts are indexed for quick changing.Specifications: -- Max depth of cut 3/16", min. part length 10"; max. work pc dims 22" w x 9" thickness. -- (2) Adjustable Bed Rollers, plus one infeed and one outfeed roller. -- Cutterhead speed 5,000 RPM and head is equipped with (110) Byrd knife inserts. -- 2-Speed gearbox provides the perfect feed rate of 20 and 30 FPM.Features: -- Massive cast iron construction throughout. -- Polished built-in table roller assists movement of rough stock. -- Segmented infeed roller and sectional chip breaker easily handles rough stock. -- Magnetic controls with emergency off switch for safer operation. -- Digital readout allows precise thickness settings. -- Hinged access to cutter head and feed rollers for quick set-up. -- 3 V-belt drive smoothly transfers power to drive train and cutter head. -- Easy access to the motor, drive train, and gearbox assists in maintenance and adjustment. -- 5"; Dust chute easily handles chip removal (requires approx. 900 CFM) -- Powerful EFC motor available in single or three-phase. -- Single phase motor 7.5 HP, 220V Only (38 Amp)

Oliver Sawmill New Carriage Wheels New battery

14" Max. blade cap., 2 HP motor, 1" dia. arbor tilts 0° - 45° via hand wheel; separate handwheel for raise and lower of the arbor. -- Includes: original miter gauge, counterweighted overhead blade guard, wrench. -- NOTE: Table and Biesemeyer Fence shown in photos have been sold and are not included with machine.

OLIVER - 299-D, ...24" Planer (8" thickness capacity) -- Capacity: 24" x 8" Thick planes stock as short as 11". -- 3-Knife steel cutterhead motor: -- 5 HP; 3 PH. -- Sectional infeed rolls: - (12) 2" Wide sections: Sectional chip breaker. -- (12) 2" Wide sections with: 1/4" Independent Lift. -- (2) Driven bed rolls; feed motor: 1 HP - 3 PH REEVES Variable speed 15 - 60 FPM.

OLIVER - 34-DD, ...Disc Sander (Double)(2) 30" Dia. steel discs; 5 HP double shafted motor turns @ 1,050 RPM.(2) Steel side tables, 40" x 15", (1) slotted and (1) plain; both tables tilt 10° up and 45° down.(1) Table with 6" manual vertical adjustment; rack travel adjustment by screw & crank. -- Complete with: Magnetic controls; (2) dust outlets; large handwheels for easy adjustments.