Equipment For Sale
10611 Results Found
$ 136,000
MLS Number 13019231 2018 Taylor X330S Forklift 8991 hours 33,000 pounds capacity 48,600 chassis weight 114" forks 132" lowered height 236" max height Tires 100% SS/FP
Call for Price
$ 6,000
TAYLOR 800036 7' W 12-Section Semi-Automatic Pneumatic Clamp Carrier, with Flattener & TightenerEquipped with: -- (71) 32"; Cap. Clamps, with 4-5/8"; W x 3-1/2"; H Jaws. -- Air motor drive. -- Dual foot pedal control.Complete with: -- Pneumatic Panel Flattener. -- Pneumatic Clamp Tightener.
$ 148,500
2018 Taylor THC-300S Cushion Tire Forklift with 3,238 hours. Overhead guard, Enclosed Cab and Fork Positioner. Fork Length 72", Lowered Ht. 94", Max Fork Ht 121". Drive tires have 20% tread remaining, Steer tires have 90% tread remaining. Some lower cab glass cracked and hoses worn. Width 62" Length 145" Height 120" Gross Weight: 42,340 lb Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.
Call for Price
$ 14,200
TECNOMA - XT10.3 RS, ...Single Sided Edgebander.5/16" (5 mm) Max. edge cap., 1-1/2" (40 mm) max. banding height, 2-3/8" (60 mm) min. panel width, and 5-1/2" (140 mm) min. length. Equipped with: -- Automatic coil feed magazine with semiautomatic feed for strips, -- Teflon® coated glue pot (Heat up time 8 Min), -- Heavy-Duty 3 mm PVC capacity guillotine, 2-roll pressure unit w/1st roller power driven via clutch with pneumatic in & out positioning; 2nd roller idler roller. Workstations: -- Double motor front & rear end trim (0.41 HP - 12,000 RPM motor ea.), tilts 0° - 15°; end trimmer mounted on 45° THK guides. -- Top & Bottom flush trims (0.46 HP - 12,000 RPM motor ea.), equipped with "Quick Release" electric connectors for easy swap out of trim motors/tooling. -- Last Station: Top & Bottom buffing unit (0.2 HP - 2,750 RPM motor ea.), both adjustable. -- Single 26 FPM fixed feed speed, 0.8 HP feed drive. Complete with: -- Sound-proof enclosure, "Special" 70 mm wide chain pads, (2) rows of upper pressure wheels (60 mm dia. ea.) with "ball bearings" (vs. bushings) for long production life.
Teco Induction Motor, Type AEVFACLQ9 Frame, 160 M 20 HP RPM 3520 Volts 230/460 3 Phase. This electric motorwas taken NEW off a LeaderMac 523 SpeedMac. There are 2 of these. Call 800-459-2148 for more info.
Call for Price
Call for Price
$ 2,500
Call for Price
$ 20,000
2015 Terex R200S Skid Steer with 3,377 hours. 60 HP, Lift Capacity at 35% 700 lb., Lift Capacity at 50% 2000 lb. Operating Weight 6370 lb. Overall Length with Bucket 133.6 in Overall Height to Top of ROPS 77 in. Width 66 in. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.
$ 39,900
2002 TEREX HR32 EXCAVATOR 5,500 HOURS BLADE THUMB 60" TILT BUCKER 48" CLEAN UP BUCKET 30" DIGGING BUCKET 12" TRENCH BUCKET 17,800 OPERATING WEIGHT GOOD CONDITION FINANCING AVAILABLE WITH NO MONEY DOWN NO PAYMENTS FOR 3 MONTHS WITH GOOD CREDIT GRANITEHE.COM
Call for Price
CAT C4.4 TIER4F DIESEL ENGINE (110HP) 5’ X 16’ SCREEN 6.5 CU YD HOPPER CAPACITY RADIAL CONVEYOR W/180 DEGREE SWING AND VARIABLE DISCHARGE HEIGHT 80,700 LB OPERATING WEIGHT HEAVY DUTY TRACK UNDERCARRIAGE LOW LEVEL REMOTE GREASING
$ 270,000
$ 215,000
CAT C4.4 TIER 4F DIESEL ENGINE (110 HP) FEEDER HOPPER W/HYD ADJUSTABLE LANDING LEGS VARIABLE SPEED CONTROL WITH BIOMASS DISCHARGE AUGER CONVEYOR 73’ 10” DRUM CENTER TO CENTER 48” WIDE 3PLY BELT HYD RAISED AND LOWERED BOOM HYD FOLD OVER FOR TRANSPORT FULL LENGTH SIDE SKIRTING ALONG MAIN CONVEYOR TWIN HYD DRIVE DISCHARGE CONVEYOR UNDERCARRIAGE WITH HEAVY DUTY TRACKS RADIO REMOTE – START/STOP FEEDER, RAISE/LOWER DISCHARGE, REVERSE AUGER HEAD DRUM BEARING GAS CARTRIDGE AUTO GREASING LOW LEVEL GREASING – TAIL DRUM
$ 129,900
DEUTZ TD 2.9 L04 (60HP) LARGE CAPACITY BIOMASS HOPPER 78'9" DRUM CENTRES GIVING A MAX STOCKPILE HEIGHT OF 34'6" AT 25 DEGREES 42" WIDE 3 PLY BELT HYDRAULIC FEED HEIGHT ADJUSTMENT HYDRAULIC FOLD FOR TRANSPORT CRAWLER TRACKS WITH PENDANT CONTROL SYSTEM 2 SPEED TRACKING LOW LEVEL GREASING
Call for Price
2015 Terex R265T Rubber Track Loader, 980 Hours, 74HP Cummins Engine, Cab/Heat/A/C, 2 Speed, Hi-Flow, 72 Bucket, Completely Serviced. Please Call For More Info
$ 24,900
2015 Terex R070T Rubber Track Skid Loader, 568 Hours, (Same As ASV RT30), 48 Bucket, Cab, Just Serviced, 30 HP Engine, 48 Wide, Joystick Controls.