Equipment For Sale

Model TC-710 - Single Phase Recycling Baler --The TC-710 Recycling Baler delivers over 45,000 lbs of crushing force featuring a 10 HP, 1 Phase electric motor. Each baler comes with an oil cooler and a 5″ diameter cylinder as a standard equipment. This mobile unit conveniently fits into a truck or trailer bed and can also be used curb-side or permanently installed in-plant. The TC-710 reduces aluminum cans or plastic bottles into a dense 20″ x 20″ x 36″ bale weighing approximately 150 lbs. --The small footprint makes it great for schools, hospitals, municipalities and breweries!Advantages of Baling --Bales can be easily stacked and stored for processing --Reduce waste cost disposal --Generate revenues from sales of bales

Turner Machinery Company Resaw Good Condition

4650# capacity @ 24" load center 188" max reach Sideshift Tilt 3388 hours on the meter

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

3000 CFM 5 HP 5-1/2” static pressure

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

Twin Air 25hp Air Compressor Call Michael: 704-692-6458

TYLER 2400 SLOT-WALL MACHINE: -- Specifications:Produces T-slot "slat-wall" for architectural/store fixtures. 4' x 8' (48" x 97") max. panel cap., 2' x 2' (24" x 24") min. panel cap., min. panel thickness = 0.5" max. panel thickness = 1.5"; The Tyler 2400 can machine up to (40) panels/Hr, depending on material density, thickness and the slot profile. -- Equipped with: (18) Router spindles all on 3" fixed centers, spindles are driven in groups of (3) with (6) 7.5 HP - 3,450 RPM motors, all router spindles rotate @ 15,400 RPM. -- Operation: Panels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return, variable feed speed control, router assembly traverses on ground & polished rails with chain drive. -- Panels are positioned along the 8' rear edge fence line, distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Overhead hold-down assembly with (2) large air cylinders and (5) arms with spring loaded clamping pads hold the panel in place. Panels are loaded from the 8' front and exit to the side. -- Includes: Operator controls for the machine cycle and a "setup" mode of operation; machine cutting cycle is initiated by a 2-hand operator safety buttons located on the right front of machine. - Produces approx. (30 - 40) panels per hour. -- Available Options at Additional Cost:Router spindles on 4'- & 100-mm centers; 48" x 121" workpiece capacity increases left-to-right workpiece (length) capacity.60" x 97" workpiece capacity increases front-to-back workpiece (width) capacity & includes (1) additional multi-spindle router head.60" x 121" workpiece capacity increases front-to-back & left-to-right workpiece capacity & includes (1) additional multi-spindle router head.

TYLER 804 Air Pod Press; Overall Platen dimension of 50" x 100", with (4) individually controlled top platens - each 25" X 50". -- Side loading on 100" side. -- 0 - 50" Motorized adjustable daylight. -- Pneumatic top pressure via 5-1/2" stroke air pods by (32) 8" Air Pods with maximum 50 PSI specific pressure. -- Spring loaded rollers in bottom platen for easy loading & unloading of stack.Overall Dimensions - 122" Long x 60" Wide x 97" High

TYLER "POWER POD" Cold Press with Motorized OpeningThis TYLER "Power Pod" Press has a 36″ X 148″ capacity, side loading on 148" -- It consists of (3) individual top mounted platens with their own controls that measure 36"; wide x 49"; long each. There are a total of (27) total air pods or (9) for each platen. -- 3-1/2″- 48″ adjustable motorized daylight opening. -- The bottom platen has spring loaded rollers for easy loading and unloading. -- Max. operating pressure is 100PSI.NEW plumbing, NEW regulator, a few NEW air bags, NEW top plates, and fully cleaned and tested.

Tyler Kerfsaver XL Resaw 1-1/4" Blades 36" Diameter Bandwheels Includes: Feed system that can tilt to mill tapered siding

Tyrone Berry carriage drive, cooling radiator, working condition

Tyron-Berry SMA 213 S/N A-1024 Carriage Drive

Tyrone Berry 50’ (2) Shotgun Drive Cylinders

Tyrone Berry SMA 260 1,500 PSI Hydraulic Carriage Drive w/US 200 HP / 1,800rpm Drive, Air cooled, Dual Heat Exchangers, Soft Hydraulic Lines s/n: A0579

Tyron Berry SMA 213

Tyrone-Berry SMA 215

Tyrone-Berry Carriage Drive Model-SMA-220, S/N A2684, No motor

SMA 213 Tyrone Berry Carriage Drive (no pump) with electric motor. Call 800-459-2148 for more info.