Equipment For Sale

This grinder was removed from service in good working condition. It is ready to load/currently in storage 200 HP Main Motor Cutters 117 F-Cutters Screen (4 ) 22" Diameter Wide with 1-1/2" Holes The width is 51” and the height is 17” (infeed opening)

Challenger Grinder with 10' Infeed Steel Belt, On Board Hydraulics.

Challenger Model Series 200 to 1000 Slow Speed Wood Grinder w/30hp 480V Motor. Infeed measures 5' Long x 2' Wide x 4' Deep. Footprint measures 7' Tall x 4' Wide x 6' Wide.

Unit was (reconditioned) in 2013. Bottom Flail Assembly replaced in 2014. Unit has a remote. CALL FOR DETAILS

Recently replaced the engine

1993 Champion 710A Series 2 -3330 hours -Tires 60% -Motor Cummins -Tight and dry -Ready to work

Champion 5 HP 575 Volt 2 Stage 24 CFM unit.

CHAMPION - HRA25-25, ...Dual Stage Air Compressor. 25 HP Commercial Duty motor; 90.1 CFM at 175 PSI and 250-gal. horizontal tank. -- Features: CHAMPION's "R" Series 2-stage cast iron pump, dome pistons, and disc valves allow for higher performance at lower RPM's; largest roller bearings in the industry. -- The 250-gal. horizontal tank is equipped with: Large pressure gauge, standard tank drain, and a hard painted finish for years of durability. -- Complete with: Large dia. air filters, OSHA approved belt guard. -- Air-cooled aftercooler.

Champion C70A Grader -3478 hrs -Cummins 4BT power -Hydrostatic drive -Articulated with front blade and fold down scarifier -Enclosed cab with heat -2 of the cylinders rebuilt, and a new cylinder made for the front blade. -Ex street department machine Clean machine!!!!!

Champion D-565T Motor Grader Rebuilt Engine With Less Than 100 Hours Has A Few Leaks Currently Used As Is For Driveways Manuals Included Runs and Operates Great

Believe Champion Swing Hammer Hog 30"

COMPLETE CHANTLAND 4234 Loose Bagging System4234 BELT-WEIGH BAGGER Including the following: -- Load Cell Weighing with "5511" Weighmeter Controller -- Color Touch Screen 5.4" size -- Single or Dual Set Point -- Calibration Routine -- Zero Tracking - Weigh Track -- Multiple Product Set-Up w/Quick Change over- (100) products -- RS-232, RS 422 Ethernet TCP/IP Connection -- NEMA 4X Poly Enclosure 16" x 14" -- Three Level Password Protection -- Requires Dedicated 120V /60 Cycles service -- Two Stage Variable Speed Control for Bulk Feed & Dribble Cut off by Weight Using VFD -- Flapper Style product Stop Gate for Positive Product Cut-Off -- Discharge Dust Collection Chute -- Spiked Agitator Above Inlet, with Drive, -- An Agitator Stirs the Product and Helps Deliver Product to the Belt. -- Surge Bin, Mounts to Flange of Packer, with Removable Lid, Inlet Flange and Dust Flange in Lid -- Approximately 10 Cubic Foot Capacity with Threated Ports for Customer Supplied Bin Level IndicatorsAP100 Automatic Bag Placer -- Bag Face 13-19 Inches -- Bag Length 24 Inches and up to 40 Inches Long -- Material of Bag Construction; Kraft Paper, Poly Plastic, Woven -- Gusseted Bags 5-1/2" Wide Gussets -- Upgrade to VEE Spout Clamp for AP10000FISCHBEIN "400NS" PLAIN SEWN CLOSURE SYSTEM -- This heavy-duty, state-of-the-art plain sewing system is designed for semi or fully automated bagging operations. -- The 400NS is specifically made for medium to high volume bagging applications that will require operating speeds up to 55 linear feet per minute @ 2.5 stitches per inch. -- This versatile unit will securely sew close woven polypropylene, multi-wall paper, and jute bags. -- Includes an infeed and standard unit is Right to Left travel.Standard features include: -- Empress model "100" two thread sewing head @ 2.5 stitches/inch -- Adjustable height high speed pedestal with casters. (31-56 inches) D4380 15" infeed -- Air thread pusher -- PLC controlled pneumatic actuators -- 24 VAC control circuit / 24 VDC solenoid valve controls,1HP, 1750 rpm motor 230 VAC single phase, or 230/380/460/575 VAC 3 PH -- NEMA 12 Electrical Components -- 180 Days System WarrantyNOTE: Minimum 6" of bag free top required

COMPLETE CHANTLAND 4234 LOOSE BAGGING SYSTEM4234 BELT-WEIGH BAGGER Including the following: -- Load Cell Weighing with "5511" Weighmeter Controller -- Color Touch Screen 5.4" size -- Single or Dual Set Point -- Calibration Routine -- Zero Tracking - Weigh Track -- Multiple Product Set-Up w/Quick Change over- (100) products -- RS-232, RS 422 Ethernet TCP/IP Connection -- NEMA 4X Poly Enclosure 16" x 14" -- Three Level Password Protection -- Requires Dedicated 120V / 60 Cycles service -- Two-Stage Variable Speed Control for Bulk Feed & Dribble Cut off by Weight Using VFD -- Flapper Style product Stop Gate for Positive Product Cut-Off -- Discharge Dust Collection Chute -- Spiked Agitator Above Inlet, with Drive, -- An Agitator Stirs the Product and Helps Deliver Product to the Belt. -- Surge Bin, Mounts to Flange of Packer, with Removable Lid, Inlet Flange and Dust Flange in Lid -- Approximately 10 Cubic Foot Capacity with Threaded Ports for Customer Supplied Bin Level IndicatorsAP100 Automatic Bag Placer -- Bag Face 13-19 Inches -- Bag Length 24 Inches and up to 40 Inches Long -- Material of Bag Construction; Kraft Paper, Poly Plastic, Woven -- Gusseted Bags 5-1/2" Wide Gussets -- Upgrade to VEE Spout Clamp for "AP10000" -- PLASTIC BAG IMPULSE SEALER

2013 Fuji Ace Robot with tooling, slip sheet tray, electric panels, safety fencing and loading included. Very nice unit with more pictures coming.

Automatic template Maker for grinding your own Molder knives

Automatic template Maker for grinding your own Molder knives

Chase Turbine Mfg. Co. Sawyer's Favorite hand set sawmill, immaculate condition (3 HB), wood & steel frame, 40' track, in track mount carriage drive drum & cable, 100 HP 220V head saw motor w/ WEG soft start MCC, include off bear belt on husk frame & outfeed belt conveyor, (1) w/ shaft mount reduction drive, 35' x 9 1/2' wide (4) strand infeed log deck w/ H-78 chain & HD reduction drive, (See Chase Edger under Edgers)ref #204, Contact Jackie 931-698-3342

Chase (2) saw board edger, 30" wide w/ (1) movable saw w/ 40 HP motor 230/460 V 1765 RPM w/ HD spiked feed rolls, (2) inserted tooth saws, outfeed steel deck table w/ bar sweep to transfer board to discharge belt, (See Chase Sawmill under Circular Sawmill), ref #204, Contact Jackie Kittrell 931-698-3342

1991 Chevrolet Kodiak Truck 366 big block Fuel injection gasoline 5 speed 105k miles Runs great 25000 g.v.w.

56 Chevy 468 Big Block with EFI, Automatic Transmission, Professionally Built, too much to list. $85,000 will trade for Equipment