Equipment For Sale

40 HP TRAVAINI Liquid Ring, Single-stage Vacuum pump. Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. Pump materials include cast iron housing, ductile iron impeller and stain less steel shaft. Shaft seals are carbon face with Viton elastomers. BALDOR 40 HP, 230/460 Volt, 3-Phase, 60 Hz, TEFC direct drive motor assembly. Sealing fluid re-circulating system includes reservoir of carbon steel with fluid level gauge and drain, high efficiency discharge separator and over sized heat exchanger. High temp switch to protect against over-temp operation. Suction line accessories include inlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve and vacuum relief valve. Heat exchanger is air cooler type made from aluminum and extended surface fins. Electrical controls include: Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet. The amps @ 230 Volt = 104; the amps @ 460 Volt = 52 amps.

Tree 2UVR Vertical Milling Machine Incudes Elephant Vise Good Condition

2005 Trelan 23RC Whole Tree Chipper, 3 knife, Cat V12 with 5,000 hours, New clutch and disk bearings. Works as it should. Approximately 5k hours makes a beautiful chip. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1989 Trelan 23 Chipper -9000 frame hours -Rebuilt C-27 CAT with 200 hours on engine -New tires -New outrigger piston -Rewired corded remote -New wireless remote -New hoses -New intakes -New bearings in the PTO -Engine Preheater -New Auto-feed system NEEDS PAINT BUT WILL GO STRAIGHT TO WORK!!!

2006 Trelan 23 -No blow by and doesn't use oil -New hood jack -New cylinder -10 sets of new blades -Extra set of belts -Disk pockets are in good shape

1988 Trelan Model 18 Whole Tree Chipper Equipped with Detroit 518 Diesel Engine, Engine Hours Unknown, New Drive Chain and New Belt, New Tire, No Separator Ready for the Woods... Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

TREMZAC 248-TR-CO Portable Shaving MillPower supply; 65 HP from P.T.O. of tractor at 540 RPM (not included ). -- Emergency shutdown included. -- Log; 5" to 22" in diameter x 96" long. -- Capacity ( shaving ) 5 to 19 cubic yards/hour. -- Hopper Magazine; 24" wide x 96" long. -- Double Axle Trailer with hydraulic brake included. -- Cutter head 24" with (8) knives -- Dimensions; 7' 3"' wide x 31' 3" long.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Custom Ceiling / Flooring Table Table Size: 32' x 6'9" to 14'3" Table Operated by Both Push Button and Key Fob Controls Floor can be built manually on the table Clamping Stud Locators at 16" & 24"

TRK Shear Head, 80 mm pins, 500 hours, $16,000

MLS Number 10109396 Trojan 2500 Wheel Loader Detroit 6V92 Engine Forks With Log Clamp 23.5-25 Tires Brakes need repair. Seller has needed parts. Includes manuals and spare parts.

Troyer Machine Dust Blower Size 26, Inlet Size 12", Outlet Size 11" w/Electric Drive and 12"x10' Incoming Pipe and 11"x4' Outgoing Pipe w/Square Adapter

Trygg Ring Logging Chains 30.5x32 Pair Brand new Never opened drums

Trygg Ring Logging Chains 23.1x26 1 set for fronts or rears Brand new Never opened drums

TSM 18' LH Drop Saw Trimmer w/Pneumatic Operated Saw Ladders, 22" Dia Saw Blades, 14' L Infeed w/Even Ender Rolls, Dual Hyd Operated Even Ender Stops, 6 Strand 20' L Lugged Incline Slanted Deck w/Even Ender Rolls, On Board AB 300 Amp MCC, Hyd Power Pack & Dust Extraction Manifold. TSM 24" x 24' x 9.5" Deep Vibratory Conveyor w/Drive. TSM Drop Down Lumber Inspection Station w/7 Strand 36' Staging Deck w/Board Dealers, Board Turners, Operator Platform, Drives, Control & Tally Console. TSM Dual Transfer Decks 10' x 45' 5 Strand w/78 Rooftop Chain & Drive, 12' x 12' 5 Strand w/3' Pop Up Bypass Transfer Gate, Has Common Drive Shaft with 1st Deck. TSM Lower Drop Down Lumber Inspection Station w/7 Strand x 25' Staging Deck w/Board Dealers, Board Turner, Operator Platform, Drives, Control, Tally Console, 17' 4 Bar Unscrambler & Even Ender Rolls. 11' 2" x 16' 5 Strand Transfer Deck w/130 Rooftop Chain, Stops & Drive. TSM 10' 4" x 25' Transfer Deck w/78 Rooftop Chain & Drive. Scan Meg Scanner w/Office Hard Drive, Software, Tally Recording System & Printers. TSM LH 16' Drop Saw Trimmer Outfeed Transfer Deck w/Even End Rolls, Decline Deck, Pop Up Bypass Transfer Sweeps on 2' Segments. Markem 5000 Series Case Coding Ink Jet Printer w/2 Applicator Heads. Mattews Jet-A-Mark Mdl D0D-8400E Board Grade Marking System.

Turner Machinery Company Resaw Good Condition

3000 CFM 5 HP 5-1/2” static pressure

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.