Equipment For Sale

Filtering

Reset All 

thru
 Used     New
Viewing Page 494 of 506
10109 Results Found
Sort By 
$ 250,000

MLS Number 12321010 WEST SALEM WSM5472 Horizontal Grinder -60” Millpower Shaker conveyor/finger screen – deck removed, used to meter flow of material fed by operator and reduce bed depth to make cross belt and head pulley magnets most efficient. -60” Eriez cross belt electro magnet. -Eriez 10K42 kW Silicon Rectifier incorporating: To convert 480 volt, 60 Hz, 3 phase AC to230 volt DC 10,000 watts output Normal convection cooled, full wave bridge circuit Fused AC switch Nema 3r Enclosure -Eries beefy magnet stand to support magnet and chain fall. -60” x 28’6” Slider Bed (Heavy Duty Feeder Type Conveyor) with 8’ section of stainless steel non-magnetic for Eriez cross belt magnet to perform at peak -20”x60” Dodge magnetic head pulley – installed to double up on magnets on conveyor, prior to material entering WSM grinder drag chain feed. Downstream from this is the WSM 5472bh Titan horizontal grinder. Schematics and wiring diagram can be supplied as well. WSM also supplied the chip discharge conveyor and magnetic head pulley and electrical panel with touch screen (by Emerson). Price includes dismantling and loading on buyer's truck. Manuals available for components.

Mike Stuck
828-773-2204
Call

$ 49,000

WSM (WEST SALEM) nice large horizontal grinder/hog. 300HP direct drive motor. Power assisted, spiked top feed roll and knurled & chromed bottom feed roll. Includes 30' infeed slider-belt conveyor. In very good condition. REDUCED $49,000.

 Burlington, NC
MACHINERY INSTALLATION CO., INC. (M.I.C.I.)
336-269-2284
Call

Call for Price

 Portland, OR
Ellison Sales, Inc.
503-244-0161
Call

Call for Price

Ellison Sales, Inc.
503-244-0161
Call

Call for Price

50' West Salem 18" Btm Drops into 19" Btm With Screen S/N 116676 15HP Motor & Drive

 Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
Call

Call for Price

Wood Pellet Manufacturing Plant Equipment;Complete with the following features: -- Design capacity 15 tons per hour. -- (1) Pellet Mill (Pellet Press) – custom built in USA and was producing at a rate of 4½ tons per hour. Comes complete with spare parts. -- WEST SALEM Model 4-4-60S Hammer Mill. -- Bulk storage. -- Conveyors to bagging system. -- Blowers Cyclones & Piping.NOTES: &#9679 Plant was planned for several pellet mills but was shut down due to lack of sales. &#9679 Operated only 3-4 years but has been down for a few years now. &#9679 All equipment remains installed. &#9679 Wood supply was from several sources: processing plants by-product, shavings from planer mills, finger jointing plant, and ground trim blocks. &#9679 No Dryer - Owner using it. &#9679 More details on request. &#9679 Professional rigging is available.

Mark Joel
800-374-5009 ext:355
Call

Call for Price

TECO 100hp 1170rpm direct-coupled motor with guard cover, powered infeed roll

Ellison Sales, Inc.
503-244-0161
Call

Call for Price

Estimated screen area per deck 134” width x 240” length. This screener will need a new bearing for the main shaft, and some welding of the internal framework. There are spare hangers, universal joints, support arms.

 Madisonville, KY
Hanner Fire Machinery
270-646-6533
Call

$ 4,500

3 phase, excellent condition.

Showcase Equipment
260-250-4645
Call

Call for Price

Western Machinery Group Profile Grinder Good Condition 3 Phase

Carolina Machinery Sales, Inc
704-288-1904
Call

Call for Price

WESTERN PNEUMATICS HEAVY DUTY FINGER JOINTER WITH THE FOLLOWING EQUIPMENT & FEATURES: -- Right & Left Shaper Section: Thickness Capacity: 3/4" - 2" maximum; Width Capacity: 1-1/2" - 8" maximum; Length Capacity: 5" min. - 36" maximum; -- (2) Scoring Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Trim Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Shaper Spindles are hydraulically powered; direct driven @ 3,600 RPM by -- (1) 60 HP Hydraulic Power Unit with (1) cartridge unit per spindle. Hydraulic conversion was performed during the first year of operation. -- Western's 2-1/2" wide feed chain with lugs on 9" centers; 15 HP variable speed drive with up to 120-lug per min feed speeds; with angle transfer conveyor, air bag pressure head with quick-change feature & brush hold-downs -- APQUIP Extrusion Type Glue Applicator complete with mixing system. Currently arranged for 3/8 finger joints including (4) 3/8" glue combs -- Manual Corner Transfer to the assembly section. (allows for inspection and rejection of blocks for poor joint quality, missing proper glue spread, etc. prior to going into assembled boards) -- 12' Pre-Assembly Infeed Conveyor with feed speed ramp up/down; with side alignment rolls and dual top and bottom pre-assembly rolls -- Flying Cutoff Saw operating from below -- Assembly Press: 20' board capacity with hydraulically powered press -- Automatic Cycling Assembly Section: Feed speed varies automatically from 50 to 200 FPM, depending on incoming block lengths. Boards advance through the Cutoff Saw to a moveable limit switch where they are cut to length with a bottom-mounted 7-1/2 HP Flying Cutoff Saw arranged for continuous non-stop assembly. The cut to length board drops down into the squeeze chamber while the next board feeds out and above the preceding board where it is cut to length. Pressed lengths are pushed out onto material outfeed arms by the following board

Louis Sicotte
800-374-5009 ext:329
Call

Call for Price

WESTERN PNEUMATICS WP12 Rotary Air LockSpecifications: -- Discharge opening: "10 x 16" -- Gear motor drive: DODGE 5 HPFeatures: -- Flange mount for installation.

Tony Cornacchione
800-374-5009 ext:432
Call

Call for Price

Baghouse (Green) W/ 200HP Blower, 75HP Blower, Catwalk and Steps, down and ready to Load

 Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
Call

Call for Price

Factory refurbished 328 Blower available immediately

 Talladega, AL
Woodland Parts & Service Inc
256-362-5097
Call

Call for Price

60" with 200HP Electric Motor

 Clarksburg, TN
LPS Equipment & Acquisition Co.
731-986-4351
Call

$ 75,000

1998 WESTERN STAR DUMP TRUCK 739,133 MILES ON CHASSIS 2,500 MILES ON NEW ENGINE NEW 3406 CAT ENGINE 18 SPEED GOOD TIRES AND BRAKES 46K REARS 18K FRONT OVERWEIGHT PERMITTED VERY GOOD CONDITION FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CRDIT GRANITEHE.COM

 Dover, NH
Granite Heavy Equipment and Finance
603-953-5983
Call

$ 77,900

2016 WESTERN STAR 4900SF SEMI 405,250 MILES DETROIT 600HP 18 SPEED 46K REARS 13.5 FRONT AXEL 2 LINE WET SYSTEM HEADACHE RACK RECENT REAR END GOOD BRAKES AND TIRES 1 OWNER FLEET MAINTAINED FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

 Dover, NH
Granite Heavy Equipment and Finance
603-953-5983
Call

$ 182,900

2024 WESTERN STAR SEMI TRACTOR 44,000 MILES DD16 600 HP ENGINE 18 SPPED 46K REARS 13,300 FRONT AXEL 3:91 GEARS 224 WHEEL BASE 5 YEAR 500K WARRANTY LIKE NEW CONDITION TRAILERS ARE NOT INCLUDED FINANCING AVAILABLE WITH NO MONEY DOWN 3 MONTHS NO PAYMENTS WITH GOOD CREDIT GRANITEHE.COM

 Dover, NH
Granite Heavy Equipment and Finance
603-953-5983
Call

$ 55,000

This 2018 Western Star 4700 is powered by a DD13 Detroit engine with an Allison automatic transmission, and 40,000 lbs rear ends. It has 11r24.5 tires on it. The truck has 521,866 miles. The truck is work ready, extremely well taken care of, and not one problem at all. If interested in this truck call Gavin 601/394/7796 Tim 251/366/3237 Kameron 251/242/5493 The truck is located in State Line, Mississippi, 467 St Peter St, 39362

 State Line, MS
AlaMiss, Inc.
601-848-7811
Call

Call for Price

2025 Western Star 49X, 13,000 miles, 18 speed manual Trans., Cummins dual cyl air compressor, Detroit DA-F-18.0-5 18,000#FL1 71.0 KPI 3.74, drop single front axle, Holland FW35 ILS 36.0" air slide fifth wheel-2" slide increments, Black vinyl interior. Warranty on Truck started on 12/31/24 and is 3 yr 300k miles on front axle, 12 month basic warranty. Trans mission, transfer case, and rear axle are 2 yr warranty. It also has the Standard Cummins Engine warranty of 2 yrs., $189,500

 Greenland, MI
Pats Heavy Equipment
906-883-3800
Call

Contact Us
  • Toll Free & Canada: (800) 477-7606
  • Direct & International: (931)381-1638
  • Location: 2508 Pillow Dr. Columbia, TN 38401
Copyright © 2020 LumbermenOnline.com - All Rights Reserved