woodworking Equipment For Sale

Biesse Akron 245 Machine was in good working condition when removed from service. Computer works, but the screen does not.

BIESSE AKRON 245 Edgebander with Corner Rounding: Left-hand material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.Specifications: -- 0.4 - 8 mm (5/16") Cap. Edgebanding thickness, min. panel width 85 mm & min. length 140 mm, panel thickness 10 - 50 mm.Equipped with: -- Adjustable top pressure beam positioning. -- Automatic strip & coil feed magazine with robust shear type 3 mm PVC guillotine. -- Hot-Melt glue system (12 min. heat up time) with Teflon coated gluepot, digital thermostats with automatic kick-down when machine is in idle mode; 1" dia. glue applicator roller. -- Pressure section with (1) large dia. "non-stick" coated drive roller & (2) chrome plated idle rollers with pneumatic positioning.Workstations: -- Front & Rear End Trims (0.33 HP - 12,000 RPM motors), motors travel on (2) straight slides and pneumatic tilt 0° - 25° on horizontal plane. -- Top & Bottom Flush Trims with "Quick Change" motors (1.0 HP - 12,000 RPM motors), digital readouts for easy setup. -- 2-Motor (0.3 HP - 12,000 RPM motors) Corner rounding unit for trimming leading & trailing upper & lower edge/corners with "Fast Position" and can be used as a second Top & Bottom fine trimmer as well. -- Top & bottom Scrapers for 3 mm thick PVC banding, digitals for horizontal adjustments. -- Top & bottom Buffing (0.5 HP - 2,800 RPM motors), units tilt 0° - 30°. -- Top & bottom (2,000 Watt) Hot Air Blowers with temperature adjustment. -- Feed Speed 39 FPM, 3 HP feed drive.Complete with: -- Microprocessor for workstations & feed speed. -- Insulated sound enclosure over all trim stations with triple split dust hood, industrial lights and viewing windows. -- Extendable side panel support rail, 12 KVA - 240 Hz digital frequency inverters. - Includes: Used tooling on all workstations.

BIESSE - AKRON 246: EDGEBANDER WITH PRE-MILL AND CORNER ROUNDING0.4 - 8 mm (5/16") Cap. Edgebanding thickness; min. panel width: 85 mm; min. length: 140 mm; panel thickness: 10 - 50 mm; automatic strip & coil feed magazine with: Robust shear type 3 mm PVC guillotine.Equipped with: -- Adjustable top pressure beam positioning. -- Hot Melt glue system (12 min. heat up time) with: Teflon coated glue pot; digital thermostats with automatic kickdown when machine is in idle mode. -- 1" Dia. glue applicator roller; pressure section with: (1) Large dia. "non-stick" coated drive roller & (2) chrome plated idle rollers with pneumatic positioning.Workstations -- Pre-Milling Station with: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors. -- Front & Rear end trims (0.33 HP - 12,000 RPM motors); motors travel on (2) straight slides; pneumatic tilt 0° - 25° on horiz. plane. -- Top & Bottom flush trims with "Quick Change" motors (1.0 HP - 12,000 RPM motors), digital readouts for easy setup. -- Corner rounding unit for trimming leading & trailing upper & lower edge/corners with "Fast Position"; can be used as a 2nd Top & Bottom fine trimmer, as well. -- Top & Bottom scrapers for 3 mm thick PVC banding; digitals for horiz. adjustments. -- Top & Bottom (2,000 Watt) hot air blowers with temperature adjustment. -- Top & Bottom buffing (0.5 HP - 2,800 RPM motors); units tilt 0° - 30°. -- Feed Speed: 39 FPM, 3 HP feed drive.Complete with: -- Microprocessor for workstations & feed speed; insulated sound enclosure over all trim stations with: Triple split dust hood; industrial lights; viewing windows. -- Extendible side panel support rail; 12 KVA - 240 Hz digital frequency inverters. -- Includes: Used tooling on all workstations.NOTE: Seller states that all workstations are functioning properly as can be seen in the video, but the End Trim needs adjustment. The Return Conveyor is not included.

BIESSE AKRON 440 AX EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications Material infeed for strips & coiled edge material like: PVC, ABS, veneer, and solid wood. -- Edge & Workpiece Capacity: 0.4 - 3 mm (0.016 - 0.12") Edge; 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5-1/2") min. panel length, and 85 mm (3.3") min. width. -- Working Units:Premilling Station: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with: Panel blow off device; SIKO digital counters for adjustments. -- EVA Gluing Unit: Edge Feeding & Pressing Unit; automatic loading of tape in rolls and strips; quick-change glue pot system. -- Pressure Section: (1) Large 150 mm dia. driven; (5) idle pressure rollers. -- Feed Speeds: Operating feed speeds: 12 & 18 MPM (39 & 60 FPM). -- Workstations: Double motor End Trim; tiltable from 0° - 15°; each motor: 0.8 kW (1 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Trimming: (2) Motors, 0.65 kW (0.87 HP) each; "Pro-Nesting" copiers; cutters: R=2 mm. -- Fine Trim/Corner Rounding Unit: (2) Motors; each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with: PVC, ABS, etc. material; wood edge banding up to 3 mm max. edge thickness. -- Top & Bottom Flat Glue Scrapper: To remove potential glue squeeze out. -- Buffing Station: Top & Bottom; (2) motors; each 0.37 kW (0.5 HP) - 2,800 RPM. -- Operator Interface:Operator Control Panel; "HDI" high definition touchscreen control; Windows XP-based. -- User-friendly graphic user interface with: Diagnostic and assisted maintenance. -- USB and Ethernet port; 1.44 MB floppy drive, automatic or manual startup. -- Complete with:High frequency motors (200 Hz): Padded sound enclosure. -- Top pressure beam with staggered double row holddown wheels mounted on ball bearings. -- Actual Model: BIESSE AKRON 440 AX

BIESSE - AKRON 855, ...Edgebander with Premill & Corner Rounding (Loaded!)Specifications: -- Edge & Workpiece Capacity: 0.4 - 15 mm (0.016" - 0.59") Edge thickness; 14 - 65 mm (0.55" - 2.56") edge height; 10 - 60 mm (0.39" - 2.36") panel thickness; 140 mm (5-1/2") min. panel length; 85 mm (3.3") min. panel width. Infeed Section: -- Premilling Unit - "FI-701"Rectifies face to be edged before applying glue; horizontal & vertical movement of (2) motors on linear guides; independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) - 12,000 RPM motors; independent copying pads on each unit, Autoset device to ensure optimum positioning of cutters according to thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit - "VC-710"With automatic edge magazine for strip & coil stock; 3 mm (0.04") PVC guillotine; "TEKNO-GLUE" System includes: Pre-Melt "QM-701"; for quick heating & tank changing with floating & bidirectional glue roller applicator & NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).WORKSTATIONS: -- End (Edge) Trimming Unit - "IN-701-V"(2) 0.35 kW (0.5 HP) - 12,000 RPM Motors; automatic 4-position programmable chamfer from Control Panel (0°, 3.6°, 11°, 15°); sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit - "RS-701"Top & bottom; (2) 0.8 kW (1 HP) - 12,000 RPM motors with superimposed motor position; 1° tilt capability; includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit - "RI-701"(2) 0.65 kW (0.87 HP) - 12,000 RPM Motors; for radius top & bottom fine trimming; unit can be tilted 0° - 45°; includes: NC axis multiple machining device. -- Corner Rounding Unit - "CR-200V"For corner rounding; top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") max. edge thickness. -- Edge Scraping Unit - "RB-701"For finishing rounded off edges in PVC or ABS up to 5 mm (0.20") thickness includes: Pneumatic Unit Lifter. -- Flat (Glue) Scraper - "RCC-700"Top & Bottom, Removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700":Top & Bottom. -- Hot Air Blower Unit - "PH-700" - (2) STEINEL "2346" 2,000 W; reactivates color of thick plastic.Complete with: -- PC-Based Control Panel with: 15" Color LCD monitor, HF (High Frequency motors on all cutting & trimming workstations. Top pressure beam programmable via positioning motor; top pressure provided by belt holddown. 36" Dia. Coil table: Padded sound enclosure. -- Manuals (as pictured).Dimensions: 280" x 42" x 72" H. - Weight: 3,500 kG (7,750 Lbs.).

BIESSE - TECHNO-LOGIC: Feed Through Boring Machine Specifications -- 125.9" (3,200 mm) Max. opening cap.; 7" (180 mm) min. opening. -- Right & left horizontal boring unit with: (20) Spindles ea. (right unit motorized). -- (8) Bottom vertical supports; each support accommodates (2) Boring blocks driven by: (2) 1.8 HP Motors (2,800 RPM); all boring blocks: 96 mm wide; 0 - 90° swivel; pneumatic locking of the drill block. -- (2) Top vertical supports; each support accommodates:(2) Boring blocks driven by: (2) 1.8 HP Motors (2,800 RPM); all boring blocks: 96 mm wide; 0 - 90° swivel; pneumatic locking of the drill block. -- All supports equipped with MICRO-DIAL Indicator for: Positioning, pneumatic locking; individual adjustment for boring block: Distance; boring depth; hydraulic brakes.Equipped with: -- Double belt through feed Conveyor with: Pneumatic squaring. -- (2) Side pressure clamps; (6) top pressure clamps. NOTE: (2) Machines available!

BIESSE - LATO 28: Edgebander, PLC Controlled. -- Specifications:Top pressure beam with: Large, staggered rubber rollers on precision bearings. -- Panel thickness: 10 - 45 mm; panel width: 50 mm Min.; panel length: Min. 150 mm; edgeband thickness (coils): 0.4 to 3 mm; edgeband thickness (strips): 8 mm Max.; track speed: 36 FPM. -- Machine Control: The PLC Electronic Control with Display and Keyboard. -- Work Units:Dual End Trimmers; Top & Bottom Tilt Trim Unit; Profile Scraper; Buffing. -- Complete with: -- Industrial granulate glue system; Heavy-Duty guillotine; pneumatic pressure rollers. -- Dual end trim motors on STAR guide system with: Pneumatic inclination. -- Heavy-Duty standalone top & bottom trim units with: Quick position digitals. -- Profile PVC scraper with: Pneumatic positioning; dual motor buffing.

BIESSE LATO 38 Edgebander. --6-Station Edgebander with 8mm (5/16") edgebanding thickness. --Capacity: Min. panel width 85 mm or 50 mm w/250 mm panel length, min. panel length 140 mm, max. panel thickness 45 mm. --Equipped with: -- Auto strip and coil feed magazine with 3 mm PVC guillotine. -- Teflon coated hot melt glue pot, dual digital thermostats, 1 in. diameter glue applicator roller. -- Pressure section w/ (1) large dia. non-stick coated drive roller and (2) pneumatic pressure controlled idle rollers, horizontal adjustment w/ digital indicator. --Workstations: -- Front and rear end trims (0.5 HP motors), motors travel on 45° slides and tilt 0 - 12° on a horizontal plane. -- Top and bottom rough trim (0.73 HP motors), motors tilt 0 - 30°. --Top and bottom fine/bevel/profile trims (0.73 HP motors), motors tilt 0 - 30°, cutters for 10° bevel and 3 mm PVC radius round, digital readouts for setup (w/ quick change motors for tool change). -- Top and bottom scrapers for 3 mm thick PVC banding, pneumatic pressure control for scraping knives, digital readout for horizontal adjustments. -- Top and bottom hot air blowers. -- Top and bottom buffing (0.5 HP motors), units tilt 0 - 30°. -- Feed chain "anti-slip" 80 mm wide rubber pads, feed speed 33 FPMand with a 2 HP feed drive.

Biesse Levia 310-1350 Sander

BIESSE - JADE 240: Edgebander (with Premill & Corner Rounding) -- Specifications• 7" Smart Touch control panel for machine operation, gluing unit controls• Two (2) motor pre-milling unit with symmetrical diamond tools• Anti-adhesive spray unit to keep panel surfaces clean• Gluing unit SP03• Two (2) motor end trim unit with pneumatic bevel• Fine trim unit RF02 with tilt and digital trim adjustments• Multi-profile insert cutters for radius/straight cutter• Two (2) motor corner rounding unit AR02 (set up for 2mm radius)• Radius Edge scraper with 2mm inserts• Glue scraper• Buffing unit• Under-hood LED cabinet lights• 12m/min feed speed• 8 mm wood strip capacity• 150mm (6") min panel length• 85mm (3.35") min panel width• Includes auto transformer• Actual Model: BIESSE JADE 240

Min. Panel Thickness: 0.39? Max Panel Thickness: 2.36? Height of Edge-Band Material: 0.55-2.51? Min. Banding Thickness: 0.01? Max Banding Thickness: 0.39? Min. Panel Length: 5.51? Min. Panel Width: 1.96? 2 Feed Speeds: 39ft/min & 59ft/min Electrical: 230V, 60Hz, 3Phase Equipped With Siemens TD200

BIESSE AKRON 1430A EDGEBANDER. -- Specifications: 0.4 - 3 mm Thickness coil edgebanding, .0.4 - 12 mm thickness of strips (HPL, veneer, solid wood strips). -- Panel thickness minimum 10 mm and 60 mm maximum. Minimum panel length 140 mm. (5.5"), minimum panel width 85 mm (3.3). -- Automatic strip & coil feed magazine with 3 mm PVC guillotine. -- Hot Melt glue system, 10 Minute heat-up time. -- 1" Dia. Glue applicator roller; pressure section with (1) large dia. "non-stick" coated drive roller.Workstations: -- Front & Rear End Trims: (0.33 HP - 12,000 RPM motors), motors travel on (2) straight slides and pneumatic tilt 0° - 25° on horizontal plane. -- Top & Bottom Rough Trims with motors (0.75 HP - 12,000 RPM motors), digital readouts for easy setup. -- Top & Bottom Fine Trims with motors (0.5 HP - 12,000 RPM). -- Top & Bottom Profile Scrapers with digital readouts for horizontal adjustments. -- Top & Bottom Glue Scrapers, digital readout for horizontal adjustments. -- Feed Speed of 12 MPM (39 FPM), 3 HP feed drive. -- Complete with: -- Insulated sound enclosure over all trim stations with dust hood. -- Extendable side panel support rail; -- SELLER STATES: Does not have pre-mill and cannot be retrofitted.

BIESSE KLEVER 1530 G FT FLAT TABLE MACHINE: -- Specifications:5' x 10' "Bridge Gantry" machine with T-Slot "Aluminum" grid table with multiple vac ports that allows vacuum locking (vacuum pump required), or T-Slot Pressure Clamps. -- Working Capacity:"X" Axis 120" (3,050 mm), "Y" axis 60" (1,550 mm), "Z" axis stroke is 10.2" (260 mm), max. material thickness 5.9" (150 mm). -- Positioning Speed:"X" & "Y" axis 74 FPM (23 MPM), "Z" axis 41 FPM (13 MPM); "X" & "Y" Axes use a precision rack & pinion system, "Z" axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work Area:Flat table design with T-Slot "Aluminum" grid table with multiple vac ports that allows vacuum locking (requires a vacuum pump).(3+3) Manual flip reference stops in "Y" axis & (2) reference stops in "X" axis. -- Machining:(1) 12 HP (8.9 kW) Air cooled "HSD" Electro-spindle with HSK F63 adaptor, variable speed from 1,000 - 24,000 RPM.(1) 7-Position ATC rack (automatic tool changer). NC controlled "Touch-off Probe", a digital presetting device for the measurement of the tool length. -- Operator Interface:PC Front End with: Biesse "BH 660" +"BiesseWorks" + Windows "WRT" operating system.19" TFT flat screen monitor, full keyboard & mouse all mounted on a mobile cart. Ethernet connection capabilities. -- BiesseWorks graphic interface with assisted graphic editor used to program machining operations, parametric programming and guided creation of parametric macros.Import of CAD and other external software files in DXF and CID3 format; 3D simulation of the tool path, calculation of machining time & the ability to create rotate virtual faces. -- Complete with: Tool Touch-off Probe for automatic program update according to the tool length Automatic Lubrication system for linear guides, pads and re-circulating ball screw Universal Autotransformer for voltages between 200-600 V, 50/60 Hz. -- Actual Model is BIESSE KLEVER 1530 G FTNote: There are NO vacuum pump(s) included. The original monitor does not work; we use a replacement monitor. Control AC unit does not work.

BIESSE - ELIX B: CNC Bore, Glue, and Dowel InserterBIESSE Drill & Dowel Inserter features: Single spindle for drilling; dowel insertion unit; glue injecting unit installed on a carriage moving in the X-axis.Position for drilling dowel insertion provided through simple programs through the NC control or third-party software. Operator Control interface is: Intuitive, user-friendly, and very easy to use. -- Specifications Max. parts length: 1,300 mm (51";); Min. parts length: 120 mm (4.7";); Parts thickness: 10 - 40 mm (0.4"; to 1-1/2";). -- Positioning Speed "X" & "Y" Axis positioning speed: 40 MPM (131 FPM); "Z" Axis has manual adjustment with: Max. stroke of 40 mm (1.57").The working unit's travel on Precision machine ground ball screws; powered by brushless AC Servo motors. -- Worktable(4) Working zones with: Center fence position in up mode; (2) large work zones in down position; (4) holddown cylinders. -- Boring UnitDrilling Unit. High-speed unit with: 6,000 RPM Spindle; max. drilling depth: 30 mm (1-1/4"); max. drill bit dia.: 12 mm (0.47"); manual adjustment of depth with: Digital indicator. -- Dowel Insertion UnitDowel prepositioning ensures high repeatability of inserting dowels for each hole; distance between the dowel insertion unit and the drilling spindle: 32 mm (1.3") For simultaneous drilling; dowel insertion when holes are spaced at 32 mm; standard dowel dimensions: 8 x 30 mm; Max. dowel projection: 14 mm (0.551"). Glue Tank: Holds up to 8 liters (3.1 gallons) of glue; max. glue density: 900 CPS.Glue inserting Unit: Flow sensor & electronic adjustment of the amount of glue. -- Operator InterfaceIndustrial numerical control with: Extremely simple Program Editor; macro & parametric programming. - Icon driven. -- Includes: Original Factory Machine Documentation. -- Actual Model: BIESSE ELIX B

Biesse Elix B Boring Machine

Biesse Elix K3

Max. Width: 51.2? Thickness: 0.4? – 1.6? Min. Depth: 4.7? X Axis:51.2? Head Movement Speed: 131.2 ft/min Z Axis: 1.6? Boring Unit: Rotation Speed: 6000 rpm Depth: 1.2? Max. Bits Diameter: 0.47? Modified Dowel Insertion Size: .19? to .24? Standard Dowel Insertion Unit: Standard Dowel Dim: 0.31? x 1.18? Max. Dowel Projection: 0.55? Glue System: Glue Tank Capacity: 2.1 gallons Max. Glue Density: 900 cps Equipped With: – The Smart-Shot Dowel Insertion Unit – 2 Sensors to Prevent Dowel or Glue Misfire. – Dowel Unloading System – Glue Electronic Proportioning – Glue Injector Sensor

BIESSE POLYMAC FSE 21-Spindle Semi-Automatic Bore, Glue & Dowel InserterSpecifications: -- Spindle head fixed horizontally for end boring. -- Dowel dia. 8 - 10 mm. -- Dowel length 25 - 50 mm. -- Max. boring depth 70 mm. -- Spindle centers 32 mm (1.26").Equipped with: -- (8) Glue injectors & dowel inserters. -- Glue tank, with Pressure control & Rinsing tank for glue nozzles. -- 8-Way Vibratory bowl feeder. -- (4) Pneumatic hold-down clamps. -- (2) Side fences. -- Front support table, with Stop. -- Foot pedal control.

Biesse Rover 15 Pod and Rail. In Great condition for its age!

BIESSE ROVER 20 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working field: "X" Axis 113.9" (2,893 mm); "Y" axis 37.4" (950 mm); "Z" axis stroke is 3.9" (100 mm), max. panel thickness 2-1/2" (65 mm). -- Positioning Speed:"X" Axis at 246 FPM (75 MPM); "Y" axis 147 FPM (45 MPM); "Z" axis 49 FPM (15 MPM)."X" Axis moves on high precision prismatic guides and ground helical rack; "Y" & "Z" axis via hardened ground ball screw. -- Worktable:(6) Pneumatically locked & manually positioned panel supports with (2) vacuum cups each.(2) Working zones with: (6) Pneumatic backstops; (2) pneumatic side & (2) center stops; stops raised & lowered automatically by start/stop of machining cycle. -- Boring Unit:(1) 2.3 HP - 5,135 RPM Motor; (10) vertical spindles independently operated with (6) in "X" axis & (4) in "Y" axis.(6) Horizontal spindles: (2 +2) in "X" Axis & (1 + 1) in "Y" axis; 2-1/2" (65 mm) max. boring depth.(1) "X" Axis grooving saw with: 120 mm Dia. blade - 5,200 RPM. -- Machining: Equipped with: (1) 9 HP (6.6 kW) Air-cooled "Quick Change" electro spindle with ISO 30 adaptor.Router is driven by: 10.2 HP (7.5 kW) Inverter for variable speed from 1,000 - 24,000 RPM; RH & LH rotation.(1) 3-Position automatic tool changer mounted at the back of the machine for "on the fly" ATC. -- Operator & Machine Control: Separate Control Console with: CNi "NC 410" Operating System housed in air-conditioned cabinet.8" LCD Monitor: Displays programming graphics, numerical & function keyboard; 512 KB RAM memory; (1) "UPGRADED" USB drive.RS-422 Serial port for PC and RS-425 port for inverter connection; EPROM for machine data & subroutines; machine runs production programs while programming and editing. -- Complete with:Stabilized autotransformer for voltages between 200 - 600 Volt 50/60 Hz; (1) 100 cbm/Hr Vacuum Pump; triple photocell barrier; assortment of misc. parts and tooling; Users operator/maintenance manuals & backup disks. -- Actual Model is: BIESSE - ROVER 20.