woodworking Equipment For Sale

Pneumatic Single Spindle Tabletop continuous operation drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 8" tabletop working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation; the bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Capacity: Materials from 1/2"- to 1-1/2" thick.Features: -- Pneumatic drill motor, pneumatic clamping. -- 15° Boring angle for greater stability, reduced screw breakout & splitting; this produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- External regulator, filter & lubricator, 3/8" cobalt drill bit, and foot pedal actuation.Requires a compressor able to produce 8 CFM at 120 PSI (50% duty cycle).

KREG DK 3100 Pocket Hole Boring MachineElectric 3-spindle Pocket Drill; 1.5 HP direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation.... Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Features: 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. -- Includes: Pressure gauge & cycle counter, fence, holddown & clamping assembly, (2) 3/8" cobalt drill bits, and foot pedal control.

KREG DK 3100 Electric 3-spindle Pocket DrillSpecifications: -- 1.5 HP Direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation. -- Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material.Features: -- 15ø Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- Pressure gauge, fence, hold down, and foot pedal control.

KREG DK 5100 5-Spindle Pneumatic Pocket Hole Machine. -- Individually actuated motors, (5) 0.75 HP motors, mounted on 6" centers. -- Hardened steel drill guides to support drill bit through the operation; 1-touch, foot pedal cycle. -- Swings stops for optimized material positioning; dust collection chutes for efficient chip removal. -- Complete with pre-filter and automatic lubricator.

KREG KFT 4X8 Face Frame Assembly. -- American-Made 4' x 8' Frame Assembly Clamp with floor stand. -- Working surface at approximately 30° angle for convenience. -- Unit includes; (4) Overhead air cylinders mounted on an overhead beam adjustable up-and-down. -- Clamping beam that moves from left-to-right by means of rollers. -- Squaring bars (fences) on the bottom and both ends of the table. -- Clamping beam with an air filter/oiler/regulator and air outlet at lower end of the beam. -- Optional pneumatic screw gun & pneumatic flex hose.

KUFO SK-12RS Straight Line Rip Saw w/Return Conveyor;Entry level Straight-Line Rip Saw with a guaranteed 6' glue line. -- Powered by a 15 HP direct drive motor. -- 12" Dia. Blade capacity for up to 3-1/4" max. cutting height, 4,200 RPM blade speed. -- Equipped with (6) holddowns and a Wye-Delta soft start for lower amp requirements during start-up. -- 1 HP Feed motor, 36 - 145 FPM feed speed, 6" chain width and automatic chain lubrication. -- Treated chain links, pins and raceways withstand heavy use because of an automatic oiler. -- Large 15-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size tablesaw. -- Complete with side mounted return conveyor.

Single belt oscillating "Tiltable Bed" 0° - 90° sander, 3 HP main motor, 3,400 RPM, belt size 6" x 89", 30.5" long platen. -- Max sanding length 30.5", 4" vertical adjustment of front table, 36" table height, oscillating rate of 121 times/min. -- Includes: (4) interchangable spindles, sizes are 1.25" - 1.5" - 2" & 2.5" dia.

Oscillating Edge Sander with end sanding kit. -- 6" Wide x 89" long abrasive belt. -- Tilting 6" x 24" platen. -- 3 HP, single or 3-Phase motor w/emergency switch. -- 6" Diameter drive pulley. -- 8" x 24" Front table with a 4" vertical adjustment and miter gauge. -- End table for radius work. -- Heavy tables, fabricated steel base and dust hood. -- 3-Phase unit model # is SK-3000SDN3.

Kuka KR60-3 Robot System KR C4 Control System Kuka Programming Smart Pad Robot Enclosure (3) Heave duty conveyor racks

KUNDIG DUPLEX 53-RC-E Wide Belt Sander (2) Heads; 52" Width cap. Drum, Combination Head.Head Configuration1st Head: 7-1/4" Dia. rubber covered contact roll, 25 HP motor.2nd Head: Combination head with rubber covered contact roll and segmented finishing platen, infeed sensors sense the panel and electronically control the platen height with timers, variable edge control can also be set, 20 HP motor.Specifications: Abrasive belt size 54" x 75" with air tensioning and electronic abrasive belt tracking, both heads with abrasive grit thickness adjustment, 2 HP Variable feed drive. -- Conveyor belt speeds 9 - 45 FPM, controlled by electronic inverter & adjustable on the control panel; infeed & outfeed rubber covered holddown rollers.Equipped with & Features: -- Workpiece thickness cap. 1/8" - 6-1/4", motorized thickness adjustment with LED readout. -- A joystick controls the conveyor opening and start/stop of the feed, automatic "over-thickness" protection and automatic conveyor belt tracking. -- Constant passline of conveyor height at 35". -- Air blow off of second head abrasive belt. -- Emergency stop button, motor load meters, magnetic controls.NOTE from the seller: There is a small leak in the air bladder . The sander has 6,541 working hours

LA NUOVA SCOLPITRICE 201-16 Multi-Spindle Carving Machine.(16) Cutter Stations, 55" max. workpiece length,Specifications: -- (16) Dual carving spindle heads, 8" between spindles, 20" max. working diameter. -- Each head has a roughing & finishing spindle, all heads swivel 360° with pneumatic locking. -- Upper carriage controlled by (2) High Frequency changers allowing (2) motor speeds of 12,000 & 18,000 RPM. -- Pneumatic chucking of material, stock turns 360°. Copy stylus of hardened and ground steel, adjustable for depth on either side. -- Traverse feed of carving heads was patented and requires no maintenance. -- Includes: Lot of tooling. Table for flat/horizontal copying.Note: Machine completely gone over and all heads rebuilt in 2011 and used sparingly since.Actual model is 201-16.

V2000 60 x96TS-1VL-ONS-OCE-06PS Transportation Simulator Performs both rotary and vertical motions Designed for testing larger crates up to 60-in. by 96-in

LACEY-HARMER E-LINE Self-contained Visible Diode Laser End ShooterEconomical self-contained Visible Diode Laser; optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° - +40° C operating temperature, 90 V for 250 nano-Sec mechanical stock. Beam angle with 5 mW - 15 mW output, 636 nm wave length. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed -- Projects a line from approx. 12' to 15' depending on area lighting -- Consisting of two parts; (1) crossbar style mounting bracket, please add...$ 143; (2) axis slide brackets for easy positioning, add...$ 125 each or alteratively a simple universal stationary mounting bracket add...$ 30.

LACEY-HARMER LD-2002 Diode LaserEconomical self-contained Visable Diode Laser, optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° to +40° C operating temperature, 90 V for 250 nano-sec surge protection. Beam angle 5 to 90 degrees, 5mW to 35mW output, 636 nm wave length for lines up to 20' projection. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed. -- Optional items consist of: Crossbar style mounting bracket, please add...$ 90; axis slide brackets for easy positioning, add...$ 125 or alteratively a simple universal stationary mounting bracket, please add...$ 30.

Laguna Bandt 4 Edgebander Machine is 6 months old Extremely low hours - Buyer upgraded to a larger machine!

LAGUNA BM23E-2 ... Double Row Line Borer(2) 23-Spindle heads on 32 mm centers, (2) 3 HP motors, drills vertically from bottom.Specifications: -- Distance between first and last spindle 851 mm (33.50"). -- Spacing between zero and max. on the first head 0 - 4". Min. distance between two heads 7.25". Max. boring line spacing to the second head 24". -- 2,800 RPM spindle speed; collets accept 10 mm shank bits. -- Heavy overhead material holddown system with (4) pneumatic material clamps. -- (2) independent air throttles to control the drill-heads upstroke speed.Complete with: -- "Set screw" drill adapters, "quick set" system for depth of drilling. -- Extension fence with (3) flip-stops and foot pedal control.

1- 5mm Boring and Inserting Unit with Vibratory Hopper 1-8mm Boring and Inserting Unit with Vibratory Hopper Power: 208v-220v, 3 Phase, 30 Amps 96? Maximum Work Zone 4 zone stops 3-Axis Control For Positioning Weight 6,000lbs Solid One-Piece Welded Tubular Steel Frame Footprint (L x W x H): 135? x 45? x 82? Shipping Dimensions (L x W x H): 42.3? x 49? x 43? Shipping Weight: 7500 lbs

LAGUNA PRO 37 WIDE BELT SANDER1-Head, 36" width cap. - Combination sanding head with 4" dia. rubberized contact roll & 3" wide "dual action" polishing platen.Equipped with: -- Abrasive belt size 37" x 75" -- Pneumatic abrasive belt tensioning. -- Electronic abrasive belt tracking. -- 20 HP main drive motor. -- 1HP Variable feed speed motor for 12 - 60 FPM. -- 1/4 HP Conveyor bed elevation motor, with digital programmable thickness set up and AUTO-SIZE thickness system as well. -- Infeed & outfeed rubber covered holddown rolls. -- 0" - 5-1/2" thickness capacity.Complete with: -- Air-operated disc brakes on sanding head, emergency stop button

Hot Air Edgebander for Preglued banding 0.4 - 1.5 mm thickness Automatic cutoff for up to 1/32" Coil feed with manual feed for strips Panel thickness 10-50mm Front and rear end trim Top/bottom trim

LANGE MASCHINEN BAU B85K Edgebanding MachineSpecifications: -- Workpiece thickness: 8 – 50 mmWorkpiece width min.: approx. 75 mmWorkpiece length min.: approx. 120 mmEdging thickness: 0,4 – 3,0 mmMax edge thickness = Workpiece thickness + 4mm (2+2)One sided automatic edge banding machine with direct glue application to straight workpieces, high frequency cut off station, high frequency top and bottom milling unit, chain feed, double roller top pressure and work piece support. For ABS,PVC, melamine and strong wood veneer roll materials as well as fixed lengths.