Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

Manufacturer Specs premill hot glue end trim top/bottom trim corner rounding scraping buffing Computer interface

Biesse Akron 245 Edgebander System is still under power until approx mid-October 2024. Touch PLC will need to be replaced. Everything else is working good on the machine. Owner has had it serviced by Biesse.

Min. Panel Thickness: 0.39? Max Panel Thickness: 2.36? Height of Edge-Band Material: 0.55-2.51? Min. Banding Thickness: 0.01? Max Banding Thickness: 0.39? Min. Panel Length: 5.51? Min. Panel Width: 1.96? 2 Feed Speeds: 39ft/min & 59ft/min Electrical: 230V, 60Hz, 3Phase Equipped With Siemens TD200

Biesse Akron 245 Machine was in good working condition when removed from service. Computer works, but the screen does not.

Pressure Beam Type: Rollers Pre-Milling Station: 2 Motors Glue Station Pressure Rollers: 4 End Trimming Station: Straight & Bevel (2 motors) Rough Milling Station: 2 Motor Fine Milling Station: 2 Motor Corner Rounding Station: 2 Motor Flat Scraping Station: Top & Bottom Profile Scraping Station: Top & Bottom Buffing Station: Top & Bottom Heat: Top & Bottom Panel Height: 10-50 mm Edge-banding Material Height: 13-55 mm Min. Thickness of Edge-Banding Strip in Rolls: 0.4-3 mm Max. Edge Thickness w/Trimming Unit: 8 mm Max. Edge Thickness w/o Trimming: 3 mm Max. Section of Solid Wood: 8 x 55 mm Panel Protrusion from Track: 25 mm Min. Panel Length: 150 mm Min. Panel Width (150mm Length): 85 mm Min. Panel Width (250mm Length): 55 mm Chain Feed Speed: 12 m/min Dimensions: 18' L x 4' W x 5' H Weight: 4,000 lbs Electrical: 230 V 3 Phase

Pressure Beam Type: Rollers Pre-Milling Station: 2 Motors Glue Station Pressure Rollers: 4 End Trimming Station: Straight & Bevel (2 motors) Rough Milling Station: 2 Motor Fine Milling Station: 2 Motor Corner Rounding Station: 2 Motor Flat Scraping Station: Top & Bottom Profile Scraping Station: Top & Bottom Buffing Station: Top & Bottom Heat: Top & Bottom Panel Height: 10-50 mm Edge-banding Material Height: 13-55 mm Min. Thickness of Edge-Banding Strip in Rolls: 0.4-3 mm Max. Edge Thickness w/Trimming Unit: 8 mm Max. Edge Thickness w/o Trimming: 3 mm Max. Section of Solid Wood: 8 x 55 mm Panel Protrusion from Track: 25 mm Min. Panel Length: 150 mm Min. Panel Width (150mm Length): 85 mm Min. Panel Width (250mm Length): 55 mm Chain Feed Speed: 12 m/min Dimensions: 18' L x 4' W x 5' H Weight: 4,000 lbs Electrical: 230 V 3 Phase

Biesse Stream B1 9.0 Edgebander With Doucet Return Conveyer 0.4 mm - 15 mm edge thickness capacity100 mm minimum panel width10 mm - 60 mm panel thickness150 mm minimum panel lengthExternal edgebanding storage and feeding magazinePremill Two (2) motorsGlue station Pre-melt hopper Glue application roller Pressure rollers, one (1) driven, six (6) idleTwo (2) motor end trimTwo (2) motor rough top/bottom trimTwo (2) motor fine top/bottom trimFour (4) motor corner roundingTop mounted milling station for solid wood edge profilingTop/bottom profile scrapeTop/bottom glue scrapeTop/bottom buffTop/bottom hot air blowersPC controlTop feed beltMotorized raise/lower of top beamVariable track speedOutboard roller supportLighted sound enclosuresDoucet return conveyor

Capacity; Edge thickness; strips (0.4 - 22mm) Edge Thickness; coiled stock; (0.4 - 3mm) Panel thickness; 10 - 60 mm (0.39 - 2.36") Work piece width min.;85 mm (3.34") Work piece length min.; 140 mm (5.51") Feed speeds 10 - 14 - 18 - 20 MPM (33 - 46 - 59 - 65 FPM) Machine Layout Motorized top beam positioning Adjustable infeed fence Pre-Milling Station "FL-502": (2) LH & RH Rotating NC controlled spindles with automatic center positioning. Infrared Heating Lamp: Preheating workpiece edge to ensure best possible surface adhesion EVA (Hot Melt) gluepot, equipped with quick pre-melting 2 Coil Magazine Pressure Section: Servo controlled programmable pressure section with (1) large driven roller and (4) idle rollers. End Trimming; Front & rear trimming motors, swivel to 0° - 15° bevel, programmable pneumatic change Rough Trimming (first set); Top/Bottom pre- or flush trimming motors Fine Trim/Bevel/Radius Trimming; Servo controlled, pneumatic pre-positioning of motors Corner Rounding; (2) Motor corner rounding Profile Scraping; Top/Bottom 2-axis NC programmable knife positioning Glue Scraping; Flat, top/bottom, digital positioning indicators, pneumatic controlled positioning Buffing; Top & Bottom buffing motors with 150 mm (6") cloth buffing wheel. fully adjustable Hot air blowers Overhead belt hold down Centralize lubrication system External multitap transformer

Brandt KTD 65 Edgebander

Edge band thickness 0.4 – 8mm (0.016" - 1/4” ) Coil cutoff maximum 0.8 x 60 mm; 3.0 x 45 mm (PVC) Edgeband height 12 - 65 mm (1/2" – 2 9/16 ") Panel length min. 160 mm (6 3/8") Panel width min. 65 mm (2 3/8") Panel thickness - min. 8 mm (5/16") - max. 60 mm (2 3/8") Feed speed – 11 m/min. Internal modem for remote diagnostic link. Smooth upper pressure rollers. Automatic feed track lubrication system. First pressure roller driven and three idle pressure rollers. Double motor end trimming unit. Program controlled indexing from straight to bevel end trimming. Fine Trimming Station: Top/bottom (2) motors, 0.35 kW (0.50 HP) 12,000 RPM, bevels 0° - 25°, with combination flush/radius/chamfer cutterheads; horizontal and vertical tracing wheels. Radius Scraping (PVC): Top/bottom with pneumatic control, pvc scrape collection box. Buffing Station: Top/bottom (2) motors, 0.09 KW (0.125 HP) 1,400 RPM.

Brandt 520 Single Sided Edgebander Edge band thickness 0.4 – 8mm (0.016" - 1/4” ) Coil cutoff maximum 0.8 x 60 mm; 3.0 x 45 mm (PVC) Edgeband height 12 - 65 mm (1/2" – 2 9/16 ") Panel length min. 160 mm (6 3/8") Panel width min. 65 mm (2 3/8") Panel thickness - min. 8 mm (5/16") - max. 60 mm (2 3/8") Feed speed – 11 m/min. Internal modem for remote diagnostic link. Smooth upper pressure rollers. Automatic feed track lubrication system. First pressure roller driven and three idle pressure rollers. Double motor end trimming unit. Program controlled indexing from straight to bevel end trimming. Fine Trimming Station: Top/bottom (2) motors, 0.35 kW (0.50 HP) 12,000 RPM, bevels 0° - 25°, with combination flush/radius/chamfer cutterheads; horizontal and vertical tracing wheels. Radius Scraping (PVC): Top/bottom with pneumatic control, pvc scrape collection box. Buffing Station: Top/bottom (2) motors, 0.09 KW (0.125 HP) 1,400 RPM.

Brandt KDN 210 Edgebander

2008 Brandt Edgebander 230Y/133V 3 Phase Currently in Production

Brandt KDF 440C Edgebander

Brandt KF 76F Edgebander: Pre-milling, top/bottom trim, buffing, extra glue pot

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.

Brandt KDF 650 Edgebander

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

Doucet MSP-CR-19-48-15-TRF-C-8-7 Conveyor