Bertheson Press Platform size 51 Wide X 102 Long with 2 16 ft shuttle driven aluminum runner platforms. Pressure 2500 psi and we ran a temperature of 350 degrees for Tego and 165 degrees for plywood. The Press can laminate Tego Film glue or pva c glue. This press is a double shuttle and can laminate up to 14 ft by double pressing on shuttle. We can get the press operational if you are interested. We only have to hook up the power. Very good condition!

Specification from owner 2007 Black Brothers 775-56” Top and Bottom Glue Spreader with an extra-large 12.5” opening designed for SIP (structural insulated panels) manufacturing. This machine is brand new and ready for immediate delivery. 575V, 3PH

BLACK-BROTHERS TOP & BOTTOM PANEL CLEANING BRUSH MACHINE

Black Brothers 22D glue spreader Max working width 50"Max working thickness 3" 1/2 Hp, 230/460 volt three phase drive motor Table passline height 40" 7-1/4" diameter x 50-1/2" long top and bottom chrome doctor rollers 9" diameter x 50-1/2" long top and bottom rubber covered applicator rollers (Please note that the top doctor roller and top applicator roller is segmented) 11-3/4" long and 38" long top roller segments

156" long x 60" wide x 80" high (3) vertical pneumatic Clamping bars (7) clamps that can be placed horizontal or vertical on perforated surface

DOUCET CLAMP CARRIER 30 SECT X 8 FT 6 IN WIDE (200+) 36" CLAMPS MODEL SRH-1 SX30- 8.5-240-36 SN 87-10-28 Includes: HYD PWR PACK, PANEL FLATTENER Dismantled and ready to load!

Doucet Clamp Carrier Model SRH-40-8.5-240-36 40 Section Clamp 8.5' Wide (240) 2-1/2" x 36" Clamps - Rapid Change Voltage: 480/3/60

- 16.5' long - 16 rotating arms and a total of 288 - 32" clamps

Good Condition 3 phase .5 HP motor

Dynma Airkomp Case Clamp Low use - ready to ship!

Maximum Assembled Product Size: 37.5” x 98” Minimum Assembled Product Size: 11.375” (vertical) x 9.75” (horizontal) with spacer blocks 7.5” (vertical) x 5.5” (horizontal) Maximum Framing Width: 4” Minimum Framing Width: 1.5” Tubular Steel Frame THK Linear Bearings and Rails (1) Allen Bradley Compact Logix PAC (4) Allen Bradley Kinetix Servos and Drives a. (1) Vertical Beam b. (1) Horizontal Beam (2) On the Upper Right Hand Clamp to ensure that uniform pressure can be applied regardless of the cut accuracy of the frame parts (1) Hoffman Upright Enclosure Allen Bradley Control Components (Push Buttons, Relays, Power Supplies, Buzzer, etc.) (1) Hoffman Air Conditioner for Electrical Enclosure EMS Press Control/Server Communication Software Package (4) Tregarne Woodwelder with Production Gun

Laminating Rolls: 61" (155 cm) roll face with thermally conductive high release silicone surface; upper and lower main rolls internally heated; temperature controlled by state-of-the-art infrared sensors and digital PID controllers Laminating Opening: 1.5" (3.8 cm) maximum opening controlled with dual air cylinders. Laminating Material Uses heat activated and pressure-sensitive materials 0 - 55" (0 - 140 cm) wide on a 3" (7.6 cm) ID core Laminating Speeds 0 to 14.5 fmp (0 to 4.5 mpm) Post Lamination: Fanless cooling system provides uniform, filtered air for thermal shock without exposure to dangerous fan blades. Vinyl Transfer Complete roll to roll transfer, lamination, and edge trimming in one pass Safety Features • Two emitter-receiver photoelectric systems protect rolls from damage. • Emergency kick cables front and rear. • All electrical and moving mechanical parts are located in bolted cabinets • Four emergency stop buttons Installation Requirement 220 to 240 VAC, 50/60 Hz, 55A. 32 A per phase. Air: 2 cfm at 100 psi, minimum(0.5 m3 at 700 vPa)

JLT Panel Pro Clamp Model 78D-5-S 5-Levels with (6) clamps each with panel flatner 110 v Single phase Will do 80”x 40”

42” Capacity Pneumatic operation

- Gold-Anodized Heating Platens (Extremely Resistant to Scratches & Abrasions) - Dynamic Piston Bearing - Multiple Heating Options: Electric / Hot Water / Thermal Oil - Electronic Temperature Control Systems Basic 70 - Pressing surface 2500 x 1250 mm - Total pressing force 700 kN - Daylight opening max 350 mm - Number of daylights 1 piece - Number of cylinders 4 piece - Diameter of cylinders 80 mm - Spec. pressure at full capacity 2,2 daN/cm2 - Spec. pressure at 2 m2 capacity 3,5daN/cm2 - Operating pressure 350 bar - Required power 1,1kW - Closing time 13 approx. sec. with electric heating platens: - Connected load approx. 18 kW - Heating time to 90°C 16 min. - Hourly consumption with 4 min 4,0 approx. kW/h - pressing time per m2 pressing - material Basic dimensions: - Overall length 2900 mm - Overall width 1450 mm - Overall height 2030 mm - Weight 2950 kg https://img1.wsimg.com/blobby/go/f551bfb5-f644-4017-9e4a-bd2a85fa653d/downloads/Basic-Press.pdf

Two Bay 52" capacity Pneumatic clamping

Specification from owner 5 Foot Wide - Midwest Automation top and bottom high pressure laminating line capable of laminating up to 5’ x 12’ panels consisting of the following equipment: Powered infeed roller conveyor PC-160 panel cleaner with top and bottom nylon brushes and dust collection shrouds. GS-417 top and bottom glue spreader with 65” panel width capacity, glue rolls are in excellent condition, separate top and bottom direct drive motors, powered opening, glue pump system. PP-500 panel positioning station for panels up to 62”W x 148”L x 1.63”T. RP-3170 heated roller press with 67”W high temperature silicone covered top and bottom rolls. SL-510 scissor lift table, 5’ x 10’ roller platform and 6000 lb. capacity. Includes 2 new recoated glue rollers and manuals. All equipment is 575V, 3PH. May consider selling pieces separately.

Ogden SL3660 RFS

Quick Clamp Carrier Model: SA-CCFP-10.5-14 10.5' Wide 14 Section Clamp: 2.5" high jaw, 38" opening Pneumatic clamp tightener Pneumatic Panel Flattener Electric Drive

Quick Clamp Rack 12' Wide Clamp: 3.5" wide, 40" opening